Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
13 results
Search Results
Item Severity of quenching and kinetics of wetting of nanofluids and vegetable oils(2009) Jagannath, V.; Prabhu, K.N.In the present work, the suitability of vegetable oil blends with mineral oil and alumina based nanofluids as quench media for industrial heat treatment was investigated. Sunflower oil, palm oil, and mineral oil were used for preparing the blends. Alumina based nanofluids of varying concentrations ranging from 0.01-4 % were used. The size of alumina particles was about 50 nm. The severity of quenching and heat transfer coefficients were estimated during quenching of copper probes. Heat transfer coefficients were estimated using a lumped heat capacitance model. The static contact angle was measured on copper substrates having a surface texture similar to the probes used for estimation of heat transfer coefficients. A dynamic contact angle analyzer was used for this purpose. The measured contact angles of nanofluids on copper were high compared to oils, indicating poor wetting by quench media that are polar in nature. Wetting characteristics had a significant effect on heat transfer coefficients estimated during quenching. Copyright © 2009 by ASTM International.Item Thermal contact at solder/substrate interfaces during solidification(2009) Nyamannavar, S.; Prabhu, K.N.Heat flux transients at the solder/substrate interface during the solidification of Sn-37Pb and Sn-3.5Ag solder alloys against metallic substrates were estimated by the lumped heat capacitance model and the contact condition was assessed by scanning electronic microscopy (SEM). Copper substrates yielded maximum contact heat flux followed by brass and aluminium substrates. The SEM study in the solder/substrate interfacial region revealed the existence of a clear gap with the aluminium substrate. A conforming contact was obtained with copper and brass substrates. © 2009 Institute of Materials, Minerals and Mining.Item Wetting behaviour and evolution of microstructure of Sn-Ag-Zn solders on copper substrates with different surface textures(2010) Satyanarayan, S.; Prabhu, K.N.The effect of surface roughness on wetting behaviour and evolution of microstructure of two lead-free solders (Sn-2.625Ag-2.25Zn and Sn-1.75Ag-4.5Zn) on copper substrate was investigated. Both solders exhibited good wettability on copper substrates having rough surface and lower wettabilty on smooth surfaces. The contact angles of solders decreased linearly with increase in surface roughness of the substrate. The exponential power law, ?=exp(-K ?n), was used to model the relaxation behaviour of solders. A high intermetallic growth was observed at the interface particularly on copper substrates with rough surface texture. A thin continuous interface showing scallop intermetallic compounds (IMC) was obtained on smooth surfaces. With an increase in surface roughness, the IMC morphology changed from scallop shaped to needle type at the Sn-2.625Ag-2.25Zn solder/substrate interface and nodular to plate like IMCs for Sn-1.75Ag-4.5Zn solder matrix. Copyright © 2010 by ASTM International.Item Wetting behaviour and evolution of microstructure of Sn-Ag-Zn solders on copper substrates with different surface textures(ASTM International, 2011) Satyanarayan, S.; Prabhu, K.N.The effect of surface roughness on wetting behaviour and evolution of microstructure of two lead-free solders (Sn-2.625Ag-2.25Zn and Sn-1.75Ag-4.5Zn) on copper substrate was investigated. Both solders exhibited good wettability on copper substrates having rough surface and lower wettabilty on smooth surfaces. The contact angles of solders decreased linearly with increase in surface roughness of the substrate. The exponential power law, ?=exp(-KT -1), was used to model the relaxation behaviour of solders. A high intermetallic growth was observed at the interface particularly on copper substrates with rough surface texture. A thin continuous interface showing scallop intermetallic compounds (IMC) was obtained on smooth surfaces. With an increase in surface roughness, the IMC morphology changed from scallop shaped to needle type at the Sn-2.625Ag-2.25Zn solder/ substrate interface and nodular to plate like IMCs for Sn-1.75Ag-4.5Zn solder matrix. Copyright © 2010 by ASTM International.Item Effect of temperature and substrate surface texture on wettability and morphology of IMCs between Sn-0.7Cu solder alloy and copper substrate(2012) Satyanarayan, S.; Prabhu, K.N.In the present work, the effect of soldering temperature (270 and 298 °C) and substrate surface texture (0.02 and 1.12 ?m) on wetting characteristics and morphology of intermetallic compounds (IMCs) between Sn-0.7Cu lead-free solder on copper substrates was investigated. It was found that increase in temperature and substrate surface roughness improved the wettability of solder alloy. However, the effect of surface roughness on wettability was significant as compared to that of temperature. The spreading of solder alloy was uniform on smooth substrate, whereas spreading of the alloy on rough substrate resulted in an oval shape. The morphology of IMCs transformed from long needle shaped to short and thick protrusions of IMCs with increase in surface roughness of the substrate. Needle shaped and thick protruded intermetallics formed at the solder/Cu interface were identified as Cu 6Sn 5 compounds. The formation of Cu 3Sn IMC was observed only for the spreading of solder alloy at 298 °C which contributed to improvement in the wettability of solder alloy on both smooth and rough substrate surfaces. © Springer Science+Business Media, LLC 2012.Item Reactive wetting of Sn-2.5Ag-0.5Cu solder on copper and silver coated copper substrates(Springer Science and Business Media, LLC, 2013) Prabhu, K.In the present work, wetting characteristics and morphology of intermetallic compounds (IMCs) formed between Sn-2.5Ag-0.5Cu lead-free solder on copper (Cu) and silver (Ag) coated copper substrates were compared. It was found that, Ag coated Cu substrate improved the wettability of solder alloy. The average values of contact angles of solder alloy solidified on Ag coated Cu substrate were reduced to about 50 % as compared to contact angles obtained on Cu substrates. Flow restrictivity for spreading of solder on Ag coated Cu was found to be lower as compared to Cu substrate. The spreading of solder alloy on Ag coated Cu exhibited halo zone. Coarse needle shaped Cu6Sn 5 IMCs were observed at the solder/Cu substrate interface whereas at the solder/Ag coated Cu interface Cu6Sn5 IMCs showed scallop morphology. The formation of Cu3Sn IMC was observed for the spreading of solder alloy on both substrates. The solder/Ag coated Cu substrate interface exhibited more particulates of Ag3Sn precipitates as compared to solder/Cu substrate interface. The improved wettability of solder alloy on Ag coated Cu substrate is due to the formation of scallop IMCs at the interface. © Springer Science+Business Media New York 2012.Item Spreading behavior and evolution of IMCs during reactive wetting of SAC solders on smooth and rough copper substrates(2013) Satyanarayan, S.; Prabhu, K.The effect of surface roughness of copper substrate on the reactive wetting of Sn-Ag-Cu solder alloys and morphology of intermetallic compounds (IMCs) was investigated. The spreading behavior of solder alloys on smooth and rough Cu substrates was categorized into capillary, diffusion/reaction, and contact angle stabilization zones. The increase in substrate surface roughness improved the wetting of solder alloys, being attributed to the presence of thick Cu 3Sn IMC at the interface. The morphology of IMCs transformed from long needle shaped to short protruded type with an increase in the substrate surface roughness for the Sn-0.3Ag-0.7Cu and Sn-3Ag-0.5Cu solder alloys. However, for the Sn-2.5Ag-0.5Cu solder alloy the needle-shaped IMCs transformed to the completely scallop type with increase in the substrate surface roughness. The effect of Ag content on wetting behavior was not significant. © 2013 TMS.Item Effect of Reflow Time on Wetting Behavior, Microstructure Evolution, and Joint Strength of Sn-2.5Ag-0.5Cu Solder on Bare and Nickel-Coated Copper Substrates(Springer New York LLC barbara.b.bertram@gsk.com, 2016) Sona, M.; Prabhu, K.N.The effect of reflow time on wetting behavior of Sn-2.5Ag-0.5Cu lead-free solder on bare and nickel-coated copper substrates has been investigated. The solder alloy was reflowed at 270°C for various reflow times of 10 s, 100 s, 300 s, and 500 s. On bare copper substrate, the intermetallic compound (IMC) thickness increased with increase in reflow time, whereas on Ni-coated Cu substrate, the IMC thickness increased up to 300 s followed by a drop for solder alloy reflowed for 500 s. The spreading behavior of the solder alloy was categorized into capillary, gravity (diffusion), and viscous zones. Gravity zone was obtained from 3.8 ± 0.43 s to 38.97 ± 3.38 s and from 5.99 ± 0.5 s to 77.82 ± 8.84 s for the Sn-2.5Ag-0.5Cu/Cu and Sn-2.5Ag-0.5Cu/Ni/Cu system, respectively. Sn-2.5Ag-0.5Cu solder alloy was also reflowed for the period corresponding to the end of the gravity zone (40 s and 80 s on bare and Ni-coated Cu, respectively). The joint strength was maximum at reflow time of 40 s and 80 s for the Sn-2.5Ag-0.5Cu/Cu and Sn-2.5Ag-0.5Cu/Ni/Cu system, respectively. The dynamic contact angle at the end of the gravity (diffusion) zone (?gz) was found to be a better parameter compared with the stabilized contact angle (?f) to assess the effect of the wettability of the liquid solder on the microstructure and joint strength. The present investigation reveals the significance of the gravity zone in assessment of optimum reflow time for lead-free solder alloys. © 2016, The Minerals, Metals & Materials Society.Item Effect of cooling rate on joint shear strength of Sn-9Zn lead-free solder alloy reflowed on copper substrate(ASTM International, 2017) Tikale, S.; Sona, M.; Prabhu, K.Reliability of the solder joint largely depends on mechanical strength, fatigue resistance, coefficient of thermal expansion, and intermetallic compound formation. Cooling rate significantly affects the physical properties of an alloy and influences the mechanical behavior of solder joints. In the present study, Sn-9Zn lead-free solder alloy was solidified on Cu substrate under furnace cooling (0.04°C/s), air cooling (0.16°C/s), and water cooling (94°C/s) conditions. The effect of varying cooling rates on the intermetallic compound (IMC) formation at the interface and the resulting joint shear strength was studied. A microstructure study revealed the presence of Cu5Zn8 and CuZn5 intermetallic compounds at the solder-substrate interface. The IMC layer thickness at the interface increased with a decrease in the cooling rate. The joint shear strength increased with an increase in the cooling rate. The air and furnace cooling resulted in the formation of a thick IMC layer. The IMC obtained from the furnace cooling was associated with micro-cracks leading to a decrease in the joint shear strength. © Copyright 2017 by ASTM International.Item The Effect of Wetting Gravity Regime on Shear Strength of SAC and Sn-Pb Solder Lap Joints(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Sona, M.; Prabhu, K.N.The failure of solder joints due to imposed stresses in an electronic assembly is governed by shear bond strength. In the present study, the effect of wetting gravity regime on single-lap shear strength of Sn-0.3Ag-0.7Cu and Sn-2.5Ag-0.5Cu solder alloys reflowed between bare copper substrates as well as Ni-coated Cu substrates was investigated. Samples were reflowed for 10 s, Tgz (time corresponding to the end of gravity regime) and 100 s individually and tested for single-lap shear strength. The single-lap shear test was also carried out on eutectic Sn-Pb/Cu- and Sn-Pb/Ni-coated Cu specimens to compare the shear strength values obtained with those of lead-free alloys. The eutectic Sn-Pb showed significantly higher ultimate shear strength on bare Cu substrates when compared to Sn-Ag-Cu alloys. However, SAC alloys reflowed on nickel-coated copper substrate exhibited higher shear strength when compared to eutectic Sn-Pb/Ni-coated Cu specimens. All the substrate/solder/substrate lap joint specimens that were reflowed for the time corresponding to the end of gravity regime exhibited maximum ultimate shear strength. © 2017, ASM International.