Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Plasma-sprayed graphene oxide reinforced alumina composite coatings on low carbon steel with improved fracture toughness, brittleness index, and microhardness(Elsevier Ltd, 2020) Amudha, A.; Nagaraja, H.S.; Shashikala, H.D.In this work, the mechanical properties of atmospheric plasma-sprayed Al2O3and Al2O3-xGO (x = 0.5, 1.0, 1.5, and 2.0 wt%) coatings on low carbon steel was evaluated using the Vickers indentation technique, and the effects of GO addition in microhardness brittleness index and fracture toughness were investigated. The Fourier-transform infrared (FTIR) spectroscopy and Field Emission Scanning Electron Microscopy (FE-SEM) techniques were employed to analyze the microstructural characterization of the plasma-sprayed coatings and to confirm the retention of GO in the Al2O3-xGO composite after the plasma spray. It was found that the Vicker's microhardness of as-sprayed Al2O3is 4.148 GPa and it decreased with the increase in the addition of GO and for Al2O3-2.0GO, it is 3.305 GPa. The fracture toughness of Al2O3is 4.86 (MPa m1/2) whereas for Al2O3-2.0GO is 16.85 (MPa m1/2). The fracture toughness has increased whereas the brittleness index has decreased as the weight percentage of GO addition is increased in the Al2O3-GO composite. Thus, the plasma-sprayed Al2O3and Al2O3-xGO coatings suggest that 2 wt% GO addition helps in the improvement of brittleness, fracture toughness, and the microhardness. © 2020 Elsevier Ltd. All rights reserved.Item Elevated temperature solid particle erosion behaviour of carbide reinforced CoCrAlY composite coatings(Institute of Physics Publishing helen.craven@iop.org, 2018) Nithin, H.S.; Desai, V.; Ramesh, M.R.CoCrAlY+WC-Co and CoCrAlY+Cr3C2-NiCr coatings are deposited on nickel based alloy using atmospheric plasma spray technique. Mechanical properties such as microhardness, adhesion strength and fracture toughness of coatings are evaluated. Elevated temperature solid particle erosion behaviour of these coatings are investigated at 600 °C using alumina erodent at 30 and 90° impact angle. Coatings are characterized utilizing Scanning electron microscope (SEM), x-ray diffraction (XRD) and Energy dispersive spectroscopy (EDS). CoCrAlY+WC-Co coating shows higher hardness, adhesion strength and fracture toughness than CoCrAlY+Cr3C2-NiCr coating. CoCrAlY+WC-Co coating exhibited approximately 3 times higher erosion resistance than CoCrAlY+Cr3C2-NiCr coating at 90° and 30° impact angles. SEM images of eroded surfaces of coatings reveals the combination of ductile and brittle fracture. CoCrAlY+Cr3C2-NiCr coating shows severe cracks, craters, carbide pull out and chipping than CoCrAlY+WC-Co coating. High temperature erosion is a combination of simultaneous building up of material by oxidation and removal of material by erosion process. Thus reforming the erosion process to oxidation modified erosion process. © 2018 IOP Publishing Ltd.Item Microstructure and tribological characteristics of APS sprayed NiCrBSi/flyash cenosphere/Cr2O3 and NiCrBSi/flyash cenosphere/Mo composite coatings at elevated temperatures(Institute of Physics Publishing helen.craven@iop.org, 2019) Nagabhushana, N.; Rajanna, S.; Mathapati, M.; Ramesh, M.R.; Koppad, P.G.; Reddy, N.C.In the present investigation NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo composite coatings are developed using atmospheric plasma spray technique on superni 76 alloy. Coatings are characterized in terms of microstructure, phase analysis, and microhardness. Tribological properties of the coatings are evaluated using a pin on disc tribometer. Test is conducted under dry sliding conditions at room temperature, 200 °C, 400 °C, and 600 °C respectively. Microstructure and worn surfaces of the coatings are analyzed by utilizing Scanning Electron Microscope (SEM) where in phase analysis is carried out using x-ray diffractometer (XRD). XRD results revealed the presence of ?-Ni as primary phase along with Ni3B, Cr7C3, SiO2 and Al2O3 as minor phases in both the NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo coatings. Among the two coatings, Mo composite coating exhibited lower porosity and higher microhardness. The friction coefficient of both the coatings decreased with increasing temperature. The wear rate is found to decrease at lower temperatures but increased at a higher temperature (>400 °C) for Cr2O3 composite coating wherein Friction coefficient is decreased with increase in the temperature for Mo composite coatings. The worn surface analysis conducted revealed abrasive wear at lower temperatures while the transition from abrasive to adhesive is observed at higher temperatures. © 2019 IOP Publishing Ltd.Item Effect of graphene oxide loading on plasma sprayed alumina-graphene oxide composites for improved anticorrosive and hydrophobic surface(IOP Publishing Ltd custserv@iop.org, 2019) Amudha, A.; Shashikala, H.D.; Asiq Rahman, O.S.; Keshri, A.K.; Nagaraja, H.S.Alumina is a widely used anticorrosive coating material for protection of metal surfaces. The graphene oxide (GO)-Alumina composite coatings can enhance the anticorrosion property of carbon steel surfaces used in an industrial scale. In the present work, the spray dried graphene oxide nanoplatelets of 0, 0.5, 1, 1.5 and 2 wt% reinforced alumina (?-Al2O3) were deposited on the low carbon steel substrate by Atmospheric Plasma Spray (APS) technique. The GO-Alumina nanocomposite coatings are characterised using XRD, FE-SEM, HR-TEM and Raman Spectroscopy. The electrochemical corrosion behaviour of the coatings on carbon steel has been examined using three electrode electrochemical method in 3.5 wt% NaCl electrolyte. A remarkable improvement in the corrosion resistance (with a corrosion current density of 0.01 nAcm-2) of about six orders with respect to pristine alumina was observed. The wettability tests revealed that, with 1.5 and 2 wt% graphene oxide nanoplatelets addition, the surface coating turned out to be hydrophobic with contact angle of 127°, from hydrophilic with contact angle 36°, which complements the anticorrosion results. The in situ reduction of GO to r-GO by APS deposition and bridging of alumina splats by the GO sheets accounts for observing the superior performance of the composite coatings. © 2019 IOP Publishing Ltd.Item Comparative hot corrosion performance of APS and Detonation sprayed CoCrAlY, NiCoCrAlY and NiCr coatings on T91 boiler steel(Elsevier Ltd, 2021) Sundaresan, C.; Rajasekaran, B.; Varalakshmi, S.; Santhy, K.; Rao, D.S.; Govindarajan, G.Hot corrosion performance of Atmospheric Plasma Spray (APS) and Detonation spray (DSC) CoCrAlY, NiCoCrAlY, and NiCr coatings on T91 steel were investigated at 650 °C for 100 cycles under Na2SO4-K2SO4-Fe2O3 mixed salt deposit in ambient air. The hot corrosion resistance of DSC coatings was found to be superior to their APS counterparts. Chromia and spinel oxides provided excellent corrosion resistance while no ?-Al2O3 was observed. DSC NiCr and APS NiCoCrAlY offered the most and the least corrosion resistance, respectively. DFT calculation was performed to validate the thermodynamic stability of each oxide and identify the precise oxide formation. © 2021 Elsevier LtdItem Thermal expansion and microstructure evolution of atmospheric plasma sprayed NiCrAlY bond coat using in-situ high temperature X-ray diffraction(Elsevier B.V., 2023) Abhijith Vijay, V.; Santhy, K.; Govindarajan, G.; Rajasekaran, B.The paper focuses on in-situ high-temperature X-ray diffraction (HT-XRD) study on atmospheric plasma sprayed NiCrAlY coating. The sample was in-situ heated from 25 °C to 1150 °C in a controlled atmosphere (3 × 10−4 bar), and the corresponding X-ray diffraction patterns for different temperatures were recorded. The effect of temperature on crystallite size, lattice strain, and coefficient of linear thermal expansion was studied. Major phases identified are γ-Ni, γ’-Ni3Al, β-NiAl, and α-Cr. The formation of stable α-Al2O3 and spinel was found above 1000 °C. The transformation of β to γ’ and γ phase was observed as a function of temperature. The equilibrium phases and the thermal expansion of disordered Face Centered Cubic (FCC) and Body Centered Cubic (BCC) phases were predicted and supported by Thermo-Calc prediction for the stable temperature range. Results showed that the non-equilibrium microstructure produced by thermal spray process did not alter the thermal expansion behaviour. In-situ treatment resulted in microstructure and elemental homogenization. The thermal expansion and mechanism of phase evolution were discussed. © 2022 Elsevier B.V.Item Thermal spray processes influencing surface chemistry and in-vitro hemocompatibility of hydroxyapatite-based orthopedic implants(Elsevier Ltd, 2024) Shankar, D.; Jayaganesh, K.; Gowda, N.; Lakshmi, K.S.; Jayanthi, K.J.; Jambagi, S.C.Orthopedic implants made from titanium are a popular choice in the medical field because of their remarkable strength-to-weight ratio. Nevertheless, they may not interact well with human blood, resulting in thrombosis and hemolysis. In fact, non-hemocompatibility is believed to be responsible for about 31 % of medical device failures in the US alone, requiring painful and expensive revision surgery. To address this issue, bioactive hydroxyapatite coatings are applied to Ti-6Al-4V implants using thermal spray techniques. However, the temperature used during thermal processing impacts the coating's surface properties, affecting the mechanical and biological properties. Furthermore, the effectiveness of HA coatings on titanium for orthopedic applications has not been validated by biocompatibility tests, particularly hemocompatibility. In this study, we aimed to investigate the relative efficacy of three thermal spray processes of different temperature ranges: Atmospheric plasma spray (APS) (high temperature), Flame spray (FS) (moderate temperature), and High-Velocity Oxy-Fuel spray (HVOF) (low temperature), and study their impact on coating's surface properties, affecting blood components and implant's strength. The crystallinity of the HA coating increased by 32 % with a decrease in the operating temperature (APS < FS < HVOF). HVOF coating exhibited a ~ 34 % and ~ 120 % improvement in adhesion strength and ~ 31 % and 59 % increment in hardness compared to APS and FS coating, respectively, attributed to its low porosity, low coating thickness (~55 μm), and high degree of crystallinity. The HVOF coating showcased a significant increase in non-hemolytic behavior, with hemolysis rates ~8 and ~ 11 times lower than APS and FS coatings, respectively, owing to its smooth texture and high degree of crystallinity (p < 0.05). Furthermore, the HVOF coating exhibited minimal blood clotting based on the whole blood clotting assay, again confirmed by PT and aPTT assays showing delayed clotting time, indicating its non-thrombogenic behavior. The number of platelets adhered to the three coatings showed no significant difference compared to Ti-6Al-4V. APS and FS coatings showed low platelet activation, unlike HVOF coating and titanium, which revealed round platelets, similar to the negative control. Neither titanium nor HA coatings exhibited antibacterial properties, which may be due to their high affinity for organic substances, which promotes bacterial adhesion and replication. Among the three thermal processes, HVOF coating displayed good apatite growth, non-hemolytic, and non-thrombogenicity with no platelet activation owing to its low processing temperature, high degree of crystallinity (89.7 %), hydrophilicity, smooth (~4 μm) and dense (~97 %) microstructural properties. The results demonstrated that the HVOF-HA coating presented in this work meets the hemocompatible requirements and shows promise for prospective application as an orthopedic implant. Furthermore, this study has the potential to significantly reduce the use of animals in in-vivo research and improve their welfare while also cutting costs. © 2024 Elsevier B.V.