Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Strength retention characteristics of concrete cubes subjected to elevated temperatures(2010) Yaragal, S.C.; Clarke, K.S.; Mahesh Babu, K.; Ashokumar, S.; Venkataramana, K.; Babu Narayan, K.S.; Chinnagiri Gowda, H.C.; Reddy, G.R.; Sharma, A.Concrete in structures is likely to be exposed to high temperatures during fire. The relative properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. The probability of its exposure to elevated temperatures is high due to natural hazards, accidents and sabotages. Therefore, the performance of concrete during and after exposure to elevated temperature is a subject of great interest to the designer. Physical changes like cracking, colour change, spalling and chemical changes like decomposition of Ca(OH)2 and the C-S-H gel take place when subjected to elevated temperatures. This work reports the characteristics of concrete at elevated temperatures. Popular normal strength grades (M20, M25, M30, M35, M40 and M45) produced by Ready Mix Concrete (RMC) India, Mangalore have been used in production of test specimens (150 mm cubes) to obtain more meaningful and realistic data. In the preliminary phase 150 mm cubes were cast, cured and tested by destructive method for gathering data on strength characteristics. Later these test samples were subjected to elevated temperatures ranging from 100°C to 800°C, in steps of 100°C with a retention period of 2 hours. After exposure, weight losses were determined and then again destructive tests were conducted to estimate the residual compressive strength. Test results indicated that weight and strength significantly reduces with an increase in temperature. © 2010 CAFET-INNOVA TECHNICAL SOCIETY.Item Effect of recuring on compressive strength of thermally deteriorated concrete cubes(2011) Prasanth, S.; Yaragal, S.C.; Babu Narayan, K.S.Concrete is found to undergo degradation when subjected to elevated temperatures during an event such as fire and lose substantial amount of its strength. The loss of strength in concrete is mainly attributed to decomposition of C-S-H and release of chemically bound water, which begins when the exposure temperature exceeds 500°C. When thermally deteriorated concrete is supplied with water there is a substantive gain in strength as a consequence of rehydration of cement that is initiated. This paper presents results of an experimental program carried out to investigate the effect of recuring on strength gain of normal strength concrete specimens subjected to elevated temperatures from 500°C to 800°C, which were subjected to retention time of two hours at the designated temperatures. © 2011 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Recuring studies on concretes subjected to elevated temperatures and suddenly cooled by water quenching(Multi-Science Publishing Co. Ltd, 2015) Yaragal, S.C.; Kittur, M.M.; Babu Narayan, K.S.Concrete is found to undergo degradation when subjected to elevated temperatures during an accidental event, such as fire and lose substantial amount of its original strength. The loss of strength in concrete is mainly attributed to the decomposition of Calcium Silicate Hydrate (C-S-H) and release of chemically bound water, which begins when the exposure temperature exceeds 500°C. When such a concrete is supplied with water and allowed to recure, it is found to recover substantial amount of its lost strength. This work is carried out to investigate the effect of recuring on strength recovery of un-blended and blended concrete specimen (100 mm cubes) subjected to elevated temperatures from 400°C to 700°C, in steps of 100°C, for a retention period of two hours at the designated temperatures. The concrete cubes immediately after exposure were subjected to thermal shock by quenching them in water, and then temperature of thermally shocked concrete is allowed to cool to room temperature. The cooled specimen were then recured in water for 1, 3, 7, 14, 21, 28, 56 days and tested for compressive strength recovery. These studies were carried out for Portland Cement (PC) based concrete and Portland & Granulated Blast Furnace Slag (70% PC + 30% GGBS) based concrete (blended concrete), and some interesting results are presented and discussed in this paper. © 2015, Multi-Science Publishing Co. Ltd. All rights reserved.Item One-part eco-friendly alkali-activated concrete – An innovative sustainable alternative(Elsevier Ltd, 2023) Rakesh Kumar Reddy, R.; Yaragal, S.C.; Srinivasa, A.S.The primary objective of this study is to develop an eco-friendly one-part alkali-activated concrete (OPAAC) by incorporating a combination of fly ash (FA), ground granulated blast furnace slag (GGBS), and micro silica (MS). In this investigation, the proportion of MS is maintained at 20% of FA, while the maximum replacement of FA with GGBS is set to 60%, varying in 20% intervals (i.e., 0%, 20%, 40%, and 60%). Further, the natural aggregates (NA) are substituted with recycled coarse aggregates (RCAs), ferrochrome slag aggregates (FCSAs), or a combination of both. The influence of GGBS and alternative aggregates (RCAs, FCSAs) on the mechanical properties of OPAAC is thoroughly examined. To provide a comprehensive assessment, the properties of OPAAC are compared against Ordinary Portland Cement (OPC) concrete (CC) of equivalent grades. Additionally, microstructural and mineralogical investigations are conducted to determine the formation of distinct hydration products, utilizing scanning electron microscopy (SEM) and X-ray diffractometry (XRD) techniques. In OPAAC containing FA, the primary hydration products identified are alkaline alumino silicate hydrates (CASH and NASH). As the GGBS content increases, calcium silicate hydrate (CSH) becomes the predominant hydration product. Furthermore, in order to assess the sustainability of OPAAC, an analysis of embodied CO2 emissions is performed, and the results are compared with CC and alkali-activated concrete. Notably, OPAAC comprising 40% FA replaced with GGBS, 50% RCAs, and 50% FCSAs demonstrates the most favourable mechanical properties and exhibits lower CO2 emissions. © 2023 Elsevier LtdItem Assessment of fly ash and ceramic powder incorporated concrete with steam-treated recycled concrete aggregates prioritising nano-silica(Springer Nature, 2024) Rao, A.U.; Shetty, P.P.; Bhandary, R.; Tantri, A.; S., S.; Yaragal, S.C.Present research involves determining the effects of a proposed novel nano-silica prioritized-steam-treated recycled concrete aggregate (RCA) on microstructural, mechanical, and durability aspects of concrete incorporated with waste ceramic powder (WCP). The study on novel nano-silica prioritized-steam-treated recycled concrete aggregate revealed that 3% nano-silica induction with 3-h steam treatment for 50% adhered mortar bonded RCA performed optimally. The physical characterization of treated RCA showed improvement compared to untreated RCA, which was confirmed by microstructure study indicating the formation of additional calcium silicate hydrates in the bonded adhered mortar of treated RCA. Furthermore, as WCP has significant contents of alumina and silica, an optimum ternary binder mix was developed with cement, fly ash, and WCP. Later, a study was performed to analyse the performance of treated RCA incorporated in WCP prioritized concrete mix. The mechanical performance of WCP prioritized concrete with treated RCA was investigated through compressive strength, flexural strength, split tensile strength, and modulus of elasticity. The quality was ensured through ultrasonic pulse velocity, water absorption, and density characterization. The durability of concrete was studied with 5% concentrated hydrochloric acid attack and sea water (pH = 8.3 to 8.7) exposure conditions for a duration of 148 days (including 28 days of portable water curing period). Overall, 30% of the ternary mixture based on WCP prioritization, 50% adhere mortar-based RCA, and 3% of nano-silica prioritization steam treatment (3 h) demonstrated the best performance in terms of both mechanical and durability aspects. The study concluded that due to its improved performance, the innovative nano-silica priority steam treatment approach could replace 100% of RCA in concrete. Furthermore, treated RCA being advantageous because of easy adoptable technique for real-time practices as well as maintaining consistency regards RCA characteristics throughout concrete mixture be the challenge. © The Author(s) 2024.