Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Usage potential of melt processed plastic pellets as a substitute to fine aggregate in porous concretes(2012) Maneeth, P.D.; Lokesh, G.; Yaragal, S.C.; Babu Narayan, K.S.Porous concrete (PC) has been used for over 30 years. Because of its high porosity, the most common usages have been in the area of storm water management, but have been limited to use in pavements with low volume traffic, because of its low compressive strength compared to conventional concrete. Domestic and industrial plastic waste management has posed a serious challenge to engineers and scientists today. In this study an attempt is made to utilize plastic waste (melt processed) from small industries as a substitute for fine aggregate (up to 10%) in producing porous concretes. The recycled plastic (melt processed) was produced by drawing industrial and domestic waste plastic into long strands which were cut to small pieces forming granules. The plastic granules (pellets) are used as substitute to sand in this investigation. This experimental investigation reports the scope for plastic waste utilization as a substitute for fine aggregate and its influence on properties like porosity, permeability, compressive strength and tensile strength of porous concretes. © 2012 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Optimization of ferrochrome slag as coarse aggregate in concretes(Techno Press technop2@chollian.net, 2019) Yaragal, S.C.; Kumar, B.C.; Mate, K.The alarming rate of depletion of natural stone based coarse aggregates is a cause of great concern. The coarse aggregates occupy nearly 60-70% by volume of concrete being produced. Research efforts are on to look for alternatives to stone based coarse aggregates from sustainability point of view. Response surface methodology (RSM) is adopted to study and address the effect of ferrochrome slag (FCS) replacement to coarse aggregate replacement in the ordinary Portland cement (OPC) based concretes. RSM involves three different factors (groUnd granulated blast furnace slag (GGBS) as binder, flyash (FA) as binder, and FCS as coarse aggregate), with three different levels (GGBS (0, 15, and 30%), FA (0, 15, and 30%) and FCS (0, 50, and 100%)). Experiments were carried out to measure the responses like, workability, density, and compressive strength of FCS based concretes. In order to optimize FCS replacement in the OPC based concretes, three different traditional optimization techniques were used (grey relational analysis (GRA), technique for order of preference by similarity (TOPSIS), and desirability function approach (DFA)). Traditional optimization techniques were accompanied with principal component analysis (PCA) to calculate the weightage of responses measured to arrive at the final ranking of replacement levels of GGBS, FA, and FCS in OPC based concretes. Hybrid combination of PCA-TOPSIS technique is foUnd to be significant when compared to other techniques used. 30% GGBS and 50% FCS replacement in OPC based concrete was arrived at, to be optimal. © 2019 Techno-Press, Ltd.Item Characterization and performance of processed lateritic fine aggregates in cement mortars and concretes(Elsevier Ltd, 2019) Yaragal, S.C.; Basavana Gowda, S.N.; C, C.Availability of river sand is becoming scarce, due to rapid increase in infrastructure projects in India. Acute shortage of river sand, has led to indiscriminate sand mining. Adverse effect of sand mining includes river bank erosion, river bed degradation, loss of biodiversity and deterioration of river water quality and ground water availability. To address the above issues, research efforts are on, to find substitutes for river sand to be used as fine aggregate in mortars and concretes. One among the locally available resources is laterite. Laterite is a product of tropical or sub-tropical weathering, which is an abundant soil material in many parts of India. An attempt has been made to characterize the processing technique to obtain good quality lateritic fine aggregates (lateritic FA). Experiments were designed and conducted to study the performance of lateritic FA as replacement to river sand, in cement mortars and concretes. Processed lateritic FA in replacement levels of 0, 25, 50, 75 and 100 wt% to river sand at all fineness levels (Zone I to Zone IV as per Indian standards) is considered. Microstructure studies were conducted to understand the arrangement of river sand and lateritic FA with cement matrix and their Interfacial Transition Zones (ITZ) using Scanning Electron Microscope (SEM). The workability and compressive strength characteristics of cement mortars and concretes are evaluated. Laterized mortars with Zone III and Zone IV fine aggregates, at all replacement levels, result in the same compressive strengths as those of control mortars. Suitable strength enhancement technique has been attempted to achieve strengths of Zone I and Zone II lateritic fine aggregates based mortars at 100 wt% replacement, to achieve strength at least equal to or more than those of control mortars. Laterized concretes have achieved nearly the same strengths as those of control concretes, at all replacement levels and for all fineness levels (Zone I to Zone IV). © 2018 Elsevier LtdItem Performance evaluation of cement mortar compositions at elevated temperatures(Associated Cement Companies Ltd., 2019) Yaragal, S.C.; Vivek, S.; Kumar, B.Natural river sand is becoming scarce day by day due to rapid growth in construction sector. There is need for alternatives to be used in place of river sand. The performance of alternatives to river sand at elevated temperatures is also important in the likely event of fire accidents. In this study, the effect of elevated temperatures on the compressive strength of mortars containing Crushed Rock Fines (CRF) and Lateritic Sand (LS) is investigated. Cement mortar cubes were cast for varied proportion of lateritic soil and quarry dust as fine aggregate. Lateritic content was varied from 25%-100%, and 50% quarry dust was adopted. After 28 days of water curing, specimens were exposed to temperatures of 200, 400, 600, and 800°C. At room temperature, the compressive strength decreases with increase in level of lateritic fine aggregate. The lateritic mortar mixes (50, 75, and 100%) have exhibited superior elevated temperature endurance characteristics at 400, 600, and 800°C when compared to control mix. Even the 25% laterized mortar has performed equally well as that of control mix. At elevated temperatures, CRF blended mix has performed very poorly. Mortar containing lateritic sand has potential for utilization in buildings and other structures, for better fire endurance in the likely event of fire accidents. © 2019 Associated Cement Companies Ltd.. All rights reserved.Item Multi-criteria optimization of fly ash and iron ore tailing based concretes subjected to elevated temperatures(Associated Cement Companies Ltd., 2019) Yaragal, S.C.; Babu Narayan, K.S.; Kumar, B.; Francis, J.G.Due to the rapid increase in concrete utilization all over the world, there is increased consumption of Ordinary Portland Cement (OPC), natural fine aggregate (NFA), and natural coarse aggregates. Increased use of OPC, is posing a serious threat due to excess CO2 emissions, and its production is highly energy intensive. On the other hand, extraction and processing stone-based fine and coarse aggregates too, is energy intensive, and the virgin resources are fast depleting. Therefore, for sustainable development, efforts are on all over the world to look for alternative materials in place of conventional ones. In this study, it is attempted to partly replace OPC with fly ash (FA) and partly replace NFA by iron ore tailings (IOT) in concretes. The performance of such concretes at ambient and elevated temperatures is also presented. Full factorial design of experiments was adopted with two control factors under three levels of replacement, i.e., FA (0, 15, and 30% by weight of OPC) and IOT (0, 50, and 100% by volume of NFA). Total nine concrete mixes were prepared and tested for their compressive strengths at room temperature, and residual compressive strengths when subjected to various levels of elevated temperatures (200, 400, 600, and 800°C), and cost of these concretes has also been analyzed. Further, three traditional multi–criteria optimization methods, i.e., grey relational analysis (GRA), technique for order of preference by similarity to ideal solution (TOPSIS), and desirability function approach (DFA) were used to optimize concrete mixes. Results showed that TOPSIS based optimization method is more significant when compared to other two methods. Further, FA-based concrete mixes showed improved performance under multi-criteria optimization. © 2019, Associated Cement Companies Ltd. All rights reserved.Item A novel approach for optimizing the processing of recycled coarse aggregates(Elsevier Ltd, 2023) Rakesh Kumar Reddy, R.; Yaragal, S.C.This paper proposes an alternative method for processing the demolition waste into high-quality recycled coarse aggregate using the ball mill. Taguchi's design of experiments based on orthogonal array was used to minimize the number of trials for saving material and time. Experiments were carried out based on L25 orthogonal array with three processing parameters: charge, revolution duration, and aggregate weight with five levels. The revolution speed of the ball mill was set to 60 revolutions per minute. The Taguchi method was then combined with grey relational analysis to achieve the best combination of processing parameters for producing high-quality aggregate. Experimental studies on water absorption, specific gravity, impact value, and abrasion value were used to assess the quality of recycled coarse aggregates. The best combination for each performance characteristic was achieved by using the mean of Signal to Noise ratio graphs. The optimal combination of processing parameter levels to generate superior quality recycled aggregates and the most significant processing parameter were identified based on the response table of means of grey relation grade. © 2023 Elsevier LtdItem Performance and microstructural investigations of processed lateritic fine aggregates in blended cement mortars exposed to elevated temperatures(Emerald Publishing, 2023) Basavana Gowda, S.N.; Yaragal, S.C.; C, C.; Goudar, S.K.Purpose: In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures. Design/methodology/approach: This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars. Findings: This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products. Originality/value: A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software. © 2023, Emerald Publishing Limited.