Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Hot-dip Aluminizing of Low Carbon Steel in Al & Al-5wt % Cr Baths(Elsevier Ltd, 2018) Huilgol, P.; Bhat, K.U.; Udupa, K.R.Hot dip aluminizing of low carbon steel is carried out in pure aluminium bath and Al-5wt% Cr bath. The coating is characterized by scanning electron microscopy and chemical composition of the coating is analysed by EDS (energy dispersive spectroscopy) attached to SEM. The coating consists of three regions, viz., outer aluminium topcoat, intermediate Fe-Al intermetallics layer and the base alloy. The intermetallics layer consists of FeAl3 and Fe2Al5 phases. Fe2Al5 is the major phase in the intermetallics layer. The growth kinetics of intermetallics layer is parabolic in nature implying that it is diffusion controlled. Addition of chromium forms Al7Cr dispersed intermetallics phases in the aluminium topcoat. Addition of chromium has no influence on the morphology of the intermetallics layer. Scratch resistance of the coating is carried out to evaluate the scratch hardness of the coating. Chromium addition improves scratch resistance of the coating. © 2018 Elsevier Ltd.Item Electroslag remelting experiments have been carried out on En 24 steel using two slag compositions in indigeneously constructed 350 KVA DC and 50 KVA AC ESR units. Detailed quantitative characterisation of the inclusions of different types has been carried out using Quantimet Image Analyser. The inclusion content in terms of volume fraction and density (No/mm2) and their size distribution in the refined ingot and the unrefined steel have been assessed. The chemical composition of selected inclusions has been established by electron probe microanalyser (EPMA). These studies are supplemented by scanning electron microscopy on typical fractured specimens. The present study shows that the DC reverse polarity mode of melting using a slag with higher silica content (10 wt%) offers the best conditions with particular reference to removal of inclusions and modification of inclusion morphology as compared to the ingots produced by DC straight polarity and AC modes of melting.(Studies on inclusion characterization in electroslag refined En24 steel) Udupa, K.R.; Subramanian, S.; Sastry, D.H.; Iyengar, G.N.K.1994Item Corrosion stability of electrodeposited cyclic multilayer Zn-Ni alloy coatings(2011) Bhat, R.S.; Udupa, K.R.; Hegde, A.C.This paper reports on a study of electrodeposition and characterisation of cyclic multilayer coatings of Zn-Ni alloy from a sulphate bath. Cyclic multilayer alloy coatings were deposited on mild steel through the single bath technique by appropriate manipulation of cathode current densities. The thickness and composition of the individual layers of the CMA deposits were altered precisely and conveniently by cyclic modulation of the cathode current during electrodeposition. Multilayer deposits with sharp change in composition were developed using square current pulses, using thiamine hydrochloride and citric acid as additives. Laminar deposits with different configurations were produced and their corrosion behaviours were studied by AC and DC methods in 5%NaCl solution. It was observed that the corrosion resistance of the CMA coating increased progressively with the number of layers (up to certain optimal numbers) and then decreased. The decrease in corrosion resistance at high degree of layering was attributed to interlayer diffusion due to less relaxation time for redistribution of metal ions at cathode during deposition. The coating configurations have been optimised for peak performance of the coatings against corrosion. It was found that CMA coating developed at cyclic cathode current densities of 3.0/5.0 A dm-2 with 300 layers showed the lowest corrosion rate (0.112×10-2 mm/year) which is ?54 times better than that of monolithic Zn-Ni alloy, deposited from the same bath. The protection efficacy of CMA coatings is attributed to the difference in phase structure of the alloys in successive layers, deposited at different current densities, evidenced by X-ray diffraction analysis. The formation of multilayers and corrosion mechanism were examined by scanning electron microscopy. © 2011 Institute of Metal Finishing.Item Surface modification by multilayered Zn-Co alloy coatings(2012) Yogesha, S.; Udupa, K.R.; Hegde, A.Nanostructured multilayer alloy or composition modulated multilayer alloy coatings of Zn-Co have been developed, and their corrosion behaviours were studied by potentiodynamic polarization and electrochemical impedance spectroscopy methods. The coatings were developed galvanostatically using square, triangular and sawtooth current pulses through single bath technique. The cyclic cathode current density and the numbers of layers have been optimised for peak performance of the coatings against corrosion. Under optimal conditions, the coatings developed using square, triangular and sawtooth current pulses were found to be respectively y100, 80 and 90 times more corrosion resistant than monolithic alloy of same thickness. The better corrosion resistances of the composition modulated multilayer alloy coatings were attributed to the dielectric barrier at the interface, as evidenced by dielectric spectroscopy. Surface morphology, multilayer formation and surface after corrosion tests were examined by scanning electron microscopy. © 2012 Institute of Materials, Minerals and Mining.Item Metastable microstructures at the interface between AISI 321 steel and molten aluminum during hot-dip aluminizing(Elsevier B.V., 2018) Huilgol, P.; Udupa, K.R.; Bhat, K.U.The microstructure at the interface between AISI 321 stainless steel and molten aluminum was investigated which occurs during the process of hot-dip aluminizing. Microstructural characterization was carried out by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The study revealed the formation of metastable FeAlm and multiple twinned Al13Fe4 phases at the interface between steel and aluminum. Multiple twinned Al13Fe4 phase exhibits pseudo tenfold electron diffraction pattern. Another metastable phase Al3(NiFe) with an orthorhombic structure was formed as one of the eutectic phase mixture in the solidified aluminum topcoat. The Al3(NiFe) phase in the eutectic shares crystallographic orientation relationship with the Al matrix. Metastable intermetallic phases are being reported for the first time during hot-dip aluminizing. © 2018 Elsevier B.V.Item Microstructural investigations on the hot-dip aluminized AISI 321 stainless steel after diffusion treatment(Elsevier B.V., 2019) Huilgol, P.; Udupa, K.R.; Bhat, K.U.The microstructure of the hot-dip aluminized AISI 321 stainless steel was studied after diffusion treatment at 900 °C for 3 h. The microstructural characterization was carried out by scanning electron microscopy, transmission electron microscopy, and X-ray diffractometry. The microstructure of the as aluminized steel consisted of two regions, viz.; aluminum topcoat and aluminide layer. During the diffusion treatment, the coating transformed into a layered structure consisting of four layers. The Fe2Al5 phase was formed in the outermost layer and the presence of Al13Fe4 quasicrystalline approximant phase was observed. The innermost layer adjacent to the base metal transformed to ferrite phase with NiAl precipitates. Next, to this layer, a disordered FeAl phase was observed. The lattice parameter of the disordered FeAl phase was found to be larger than that of the ordered B2 FeAl phase. The layer between outer Fe2Al5 phase and disordered FeAl phase consists of a mixture of three phases, namely Fe2Al5, disordered FeAl and a new phase with the simple cubic structure. The phase with simple cubic structure shares cube on cube crystallographic orientation relationship with the disordered FeAl phase. © 2019 Elsevier B.V.