Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Microwave-assisted In-situ catalytic co-pyrolysis of polypropylene and polystyrene mixtures: Response surface methodology analysis using machine learning(Elsevier B.V., 2023) Kamireddi, D.; Terapalli, A.; Sridevi, V.; Tukaram Bai, M.T.; Surya, D.V.; Sankar Rao, C.S.; Jeeru, L.R.Polypropylene (PP) and Polystyrene (PS) are the major plastic fractions found in mixed plastic waste. Hence, the current study was focused to convert PP and PS into useful products via microwave-assisted pyrolysis (MAP). In addition, the understanding of feedstock conversion, product yields, and energy requirements in pyrolysis, co-pyrolysis, and catalytic co-pyrolysis was investigated. Experiments were conducted at a constant microwave power of 450 W till the reaction temperature reached up to 600 °C. When PS pyrolyzed, a heating rate of 56 °C/min resulted in 80 wt% of oil yield. Whereas PP pyrolysis produced 42 wt% of oil at a heating rate of 76 °C/min. In the PP: PS co-pyrolysis, the heating rate was decreased to 52 °C/min by yielding 51 wt% of oil. In catalytic co-pyrolysis of PP: PS with KOH resulted in variation in product yields and heating rate. An increase in PS quantity at a constant mass of PP resulted in the enhancement of oil yields from 58 to 84 wt% and a decrease in gas yields. The specific microwave power in the catalytic co-pyrolysis (7–18 W/g) is lower compared to the non-catalytic case (22–30 W/g). Whereas, the pyrolysis time in non-catalytic pyrolysis (7–11 min) is lower compared to catalytic co-pyrolysis (14–37 min). The addition of a catalyst resulted in a decrease (23–50%) in microwave conversion efficiency than that of the non-catalytic case (60–85%). The difference in predicted and actual result analysis proved co-pyrolysis synergy in product formation and energy consumption. © 2023 Elsevier B.V.Item A review on analysis of biochar produced from microwave-assisted pyrolysis of agricultural waste biomass(Elsevier B.V., 2023) Ramesh, R.; Surya, D.V.; Sankar Rao, C.S.; Yadav, A.; Sridevi, V.; Remya, N.Every year the agricultural product processing industries produce large quantities of agricultural waste biomass (AWB). Whose disposal has become a serious issue concerning solid waste management due to environmental and health issues. Microwave-assisted pyrolysis (MAP) is an intriguing technology for producing valuable products from waste feedstocks. AWB is converted into a valuable product like biochar by using MAP. The conversion of AWB into biochar by MAP is influenced by several factors such as type of feedstock, pyrolysis temperature, residence time, pressure, heating rate, susceptor, particle size, and microwave power. However, no review article is available to understand the role of MAP on biochar production from AWB. The current review focused on understanding the fundamentals of biochar production. It also reviews the challenges in producing biochar process by compatible, acceptable, and sustainable and its future directions to gain economic benefits even at small-scale applications. The generation of biochar from MAP and its uses in agriculture are discussed. The current review would address the knowledge gap and highlight the critical implications in biochar production and applications. © 2023 Elsevier B.V.Item Utilizing support vector regression modeling to predict pyro product yields from microwave-assisted catalytic co-pyrolysis of biomass and waste plastics(Elsevier Ltd, 2023) Ramesh, P.; Sankar Rao, C.S.; Surya, D.V.; Kumar, A.; Basak, T.The rise in plastic waste production has led to the development of co-pyrolysis of waste plastics and biomass as a potential solution. This process converts waste into valuable resources, including chemicals and pollutant-absorbing materials. Accurately predicting product yields is crucial and involves considering feedstock characteristics and pyrolysis conditions. No previous work on machine learning (ML) predicts pyro-products considering catalyst and blend as input features. This study used a support vector machine (SVM) to predict pyro-product yields from microwave-assisted co-pyrolysis of biomass and plastics. SVM models were trained, validated, and then applied to new data. The results showed high predictive accuracy, with R2 values of 0.96, 0.93, and 0.91 for bio-oil, biochar, and biogas, respectively. The SVM model demonstrated strong predictive capabilities, indicating effective generalization ability based on statistical parameters. Additionally, SVM models incorporating all features performed better than those based on 'elementary analysis (EA)' and 'proximate analysis (PA)' alone. The pearson correlation coefficient (PCC) approach assessed the correlation between input features to remove highly correlated variables. The partial dependence analysis reveals the individual effects of influential factors and their interactions in the co-pyrolysis process, highlighting significant features like carbon, hydrogen, ash, volatile matter, and nitrogen content that influence oil, char, and gas yields, thereby providing valuable insights for optimization strategies in co-pyrolysis. © 2023 Elsevier LtdItem Two-step synthesis of biochar using torrefaction and microwave-assisted pyrolysis: Understanding the effects of torrefaction temperature and catalyst loading(Elsevier B.V., 2023) Ramesh, P.; Sankar Rao, C.S.; Surya, D.V.; Sridevi, V.; Kulkarni, A.The study focused on synthesizing the biochar from sawdust using torrefaction followed by pyrolysis. Sawdust was torrefied at different temperatures (125 °C, 150 °C, and 175 °C) using a conventional hot air oven. The obtained torrefied biochar was subjected to Microwave-assisted pyrolysis at a power of 300 W for 10 min. Graphite was used as a susceptor, and KOH was used as a catalyst. The maximum biochar product yield varied from 24 to 48 wt% and increased with torrefaction temperature. The average heating rates ranged from 54.5 to 74.6 °C/min. At 10 g of KOH, higher heating rates were obtained. The pyrolysis index analyzed varied between 97.5 and 111.5 and decreased with the increase in torrefaction temperature. The obtained biochar was analyzed using SEM, BET, XRD, FTIR, ICP-OES, and Raman spectroscopy. Porous structure formation enhanced, and the concentrations of Ca, Al, and Fe decreased with the increase in torrefaction temperature. © 2023 Elsevier B.V.Item Synergistic effects and product yields in microwave-assisted in-situ co-pyrolysis of rice straw and paraffin wax(Institution of Chemical Engineers, 2024) Hamzah, H.T.; Sridevi, V.; Surya, D.V.; Ramesh, P.; Sankar Rao, C.; Palla, S.; Abdullah, T.A.Microwave-assisted pyrolysis is one of the most efficient methods for solid waste management. This study employed microwave-assisted catalytic co-pyrolysis to convert Paraffin wax (PW) and rice straw (RS) into valuable char, gas, and oil products. KOH and graphite were used as the catalyst and susceptor, respectively. The RS and PW blend served as the feedstock (with a blend ratio of 0–10 g). The yields of co-pyrolysis at different blending ratios of RS: PW exhibited variations in char content (ranging from 9.8% to 22.6% by wt.), oil production (ranging from 34.1% to 76.9% by wt.), and gas formation (ranging from 13.2% to 47.5% by wt.). The effects of the RS: PW ratio on the average heating rate, feedstock conversion, and product yields were also investigated. Analyses were performed to assess the synergistic impacts on product yields, average heating rates, and conversion factors. Notably, co-pyrolysis synergy led to increased oil and char production. Furthermore, we conducted FTIR analysis on the oil and char produced through the catalytic co-pyrolysis of RS: PW. In conjunction with co-pyrolysis synergy, the catalyst facilitated the formation of amides, alkenes, aliphatic compounds, and aromatic compounds. © 2023 The Institution of Chemical EngineersItem Effective electronic waste valorization via microwave-assisted pyrolysis: investigation of graphite susceptor and feedstock quantity on pyrolysis using experimental and polynomial regression techniques(Springer, 2024) Mistry, C.; Surya, D.V.; Ramesh, R.; Basak, T.; Kumar, P.S.; Sankar Rao, C.S.; Gautam, R.; Sridhar, P.; Choksi, H.; Remya, N.Waste printed circuit board (WPCB) was subjected to microwave-assisted pyrolysis (MAP) to investigate the energy and pyrolysis products. In MAP, pyrolysis experiments were conducted, and the effects of WPCB to graphite mass ratio on three-phase product yields and their compositions were analyzed. In addition, the role of the initial WPCB mass (10, 55, and 100 g) and susceptor loading (2, 22, and 38 g) on the quality of product yield was also evaluated. By using design of experiments, the effects of graphite susceptor addition and WPCB feedstock quantity was investigated. A significant liquid yield of 38.2 wt.% was achieved at 38 g of graphite and 100 g of WPCB. Several other operating parameters, including average heating rate, pyrolysis time, microwave energy consumption, specific microwave power used, and product yields, were optimized for the MAP of WPCB. Pyrolysis index (PI) was calculated at the blending of fixed quantity WPCB (100 g) and various graphite quantities in the following order: 2 g (21) > 20 g (20.4) > 38 g (19.5). The PI improved by increasing the WPCB quantity (10, 55, and 100 g) with a fixed quantity of graphite. This work proposes the product formation and new reaction pathways of the condensable compounds. GC–MS of the liquid fraction from the MAP of WPCBs without susceptor resulted in the generation of phenolic with 46.1% relative composition. The addition of graphite susceptor aided in the formation of phenolic and the relative composition of phenolics was found to be 83.6%. The area percent of phenol increased from 42.8% (without susceptor) to 78.6% (with susceptor). Without a susceptor, cyclopentadiene derivative was observed in a very high composition (~ 31 area %). © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2023.Item A review on the role of various machine learning algorithms in microwave-assisted pyrolysis of lignocellulosic biomass waste(Academic Press, 2024) Mafat, I.H.; Surya, D.V.; Sankar Rao, C.S.; Kandya, A.; Basak, T.The fourth industrial revolution will heavily rely on machine learning (ML). The rationale is that these strategies make various business operations in many sectors easier. ML modeling is the discovery of hidden patterns between multiple process parameters and accurately predicting the test values. ML has provided a wide range of applications in Chemical Engineering. One major application of ML can be found in the microwave-assisted pyrolysis (MAP) of lignocellulose bio-waste. MAP is an energy-efficient technology to obtain high-saturated hydrogen-rich liquid fuels. The main focus of this review study is understanding the utilization of various types of ML algorithms, including supervised and unsupervised techniques in microwave-assisted heating techniques for diverse biomass feedstocks, including waste materials like used tea powder, wood blocks, kraft lignin, and others. In addition to developing effective ML-based models, alternative traditional modeling approaches are also explored. In addition to various thermochemical conversion processes for biomass, MAP is also briefly reviewed with several case studies from the literature. The conventional modeling methodology for biomass pyrolysis with microwave heating is also discussed for comparison with ML-based modeling methodologies. © 2024 Elsevier Ltd