Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Defence applications of polymer nanocomposites(Defense Scientific Information and Documentation Centre, 2010) Kurahatti, R.V.; Surendranathan, A.O.; Kori, S.A.; Singh, N.; Kumar, A.V.R.; Srivastava, S.The potential opportunities promised by nanotechnology for enabling advances in defence technologies are staggering. Although these opportunities are likely to be realised over a few decades, many advantages are currently being explored, particularly for defence applications. This review provides an insight into the capabilities offered by nanocomposites which include smart materials, harder/lighter platforms, new fuel sources and storage as well as novel medical applications. It discusses polymer-based nanocomposite materials, nanoscale fillers and provides examples of the actual and potential uses of nanocomposite materials in defence with practical examples. © 2010, DESIDOC.Item Role of zirconia filler on friction and dry sliding wear behaviour of bismaleimide nanocomposites(2011) Kurahatti, R.V.; Surendranathan, A.O.; Srivastava, S.; Singh, N.; Ramesh Kumar, A.V.; Suresha, B.This paper discusses the friction and dry sliding wear behaviour of nano-zirconia (nano-ZrO2) filled bismleimide (BMI) composites. Nano-ZrO2 filled BMI composites, containing 0.5, 1, 5 and 10wt.% were prepared using high shear mixer. The influence of these particles on the microhardness, friction and dry sliding wear behaviour were measured with microhardness tester and pin-on-disc wear apparatus. The experimental results indicated that the frictional coefficient and specific wear rate of BMI can be reduced at rather low concentration of nano-ZrO2. The lowest specific wear rate of 4×10-6mm3/Nm was observed for 5wt.% nano-ZrO2 filled composite which is decreased by 78% as compared to the neat BMI. The incorporation of nano-ZrO2 particles leads to an increased hardness of BMI and wear performance of the composites shows good correlation with the hardness up to 5wt.% of filler loading. The results have been supplemented with scanning electron micrographs to help understand the possible wear mechanisms. © 2011 Elsevier Ltd.Item Role of nickel filler on friction and dry sliding wear behavior of bismaleimide nanocomposite(2011) Kurahatti, R.V.; Surendranathan, A.O.; Srivastava, S.; Singh, N.; Ramesh Kumar, A.V.; Kori, S.A.Nano-sized metal particles filled polymer composites are finding numerous tribological applications in recent years. In the present work, the matrix properties were investigated by introducing nickel (Ni) nanoparticles (60-100 nm, weight fractions of 0.5-10 %) into a bismaleimide (BMI) resin. The influence of these particles on the microhardness, friction and dry sliding wear behavior were measured using microhardness tester, pin-ondisc wear set up. The experimental results indicated that the coefficient of friction and the specific wear rate (SWR) of BMI resin can be reduced at rather low weight fraction of Ni particles. The lowest SWR of 9 ×10 -6 mm 3/Nm (i.e. 50% lower than the value of neat BMI) was observed for the nanocomposite with Ni weight fraction of 1%. The incorporation of Ni particles leads to an increased hardness of BMI and the wear performance of the composites shows good correlation with the hardness. The results have been supplemented with scanning electron micrographs to help understand the possible wear mechanisms. © 2011 CAFET-INNOVA TECHNICAL SOCIETY.Item Friction and dry sliding wear of bismaleimide filled with carbon nanotubes(Taylor and Francis Ltd. maney@maney.co.uk, 2016) Kurahatti, R.V.; Surendranathan, A.O.; Mordina, B.; Naik, P.; Auradi, V.Three types of bismaleimide–carbon nanotubes (CNTs) nanocomposites were fabricated using two types of original multiwalled CNTs with different diameters and one amide functionalized CNTs. The influence of diameter, content and functionalization of CNTs on the flexural and dry sliding wear behaviour were measured with universal testing machine and pin-on-disc wear apparatus. The experimental results indicated that at 1.5 wt-%, the bismaleimide-functionalized MWCNTs exhibited highest flexural strength of 156 MPa which is increased by 164% as compared to the neat matrix, and lowest specific wear rate of 1.8 × 10?4 mm3 N?1 m?1 which is decreased by 90% as compared to the neat matrix. This was attributed to the dispersion of CNTs in the matrix and the filler-matrix adhesion and internal strength of the composite. © 2016 Informa UK Limited, trading as Taylor & Francis Group.