Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating(Institute of Physics Publishing helen.craven@iop.org, 2018) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi superalloy powder (Tribaloy-T400) consists of intermetallic laves phase and primary eutectic phase of Co-rich solid solution. Processing of Tribaloy-T400 powder is carried out through high-energy ball milling (HEBM) technique to obtain a higher volume fraction of intermetallic laves phases. The feedstock is sprayed using high-velocity-oxy-fuel (HVOF) process on titanium grade-15 substrate. The coating microstructure is homogenized by microwave hybrid heating technique. Characterization of feedstock, as-sprayed and microwave fused coatings is done by using Scanning Electron Microscopy (SEM), Energy dispersive spectroscopy (EDS) and x-ray Diffraction (XRD). Porosity, surface roughness, microhardness, and bond strength are measured. Adhesive wear behavior of the coatings under the dry sliding condition is evaluated at an applied load of l0 and 20 N and temperature of 200, 400 and 600 °C Fused coating exhibit higher wear resistance than the as-sprayed coatings and substrate. The hard intermetallic laves phases which are amorphous (bulk metallic glass) in nature strengthen the coating at high temperatures. © 2018 IOP Publishing Ltd.Item Microstructure and tribological behavior of flame sprayed and microwave fused CoMoCrSi/CoMoCrSi-Cr3C2 coatings(Institute of Physics Publishing helen.craven@iop.org, 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This present work deals with the investigation of dry sliding wear behavior of CoMoCrSi and CoMoCrSi-Cr3C2 depositing on titanium substrate through Flame spray process, subsequently fused by the microwave hybrid heating process. Prior to the deposition of the coating, CoMoCrSi powder is milled by using high energy ball milling (HEBM) process and later 30% of Cr3C2 powder is added. Microstructural features and phase analysis of milled powders, as-coated and microwave fused coatings are inspected by using SEM with EDS and XRD process respectively. The coatings before and after fusing are tested for microhardness and bond strength by using a Vickers microhardness and universal tensile machines respectively. Dry sliding wear behavior of coatings before and after fusing is conducted against alumina counter face at ambient and elevated temperatures, also normal load is varied. The wear mechanism of both coatings is examined by employing XRD, SEM-EDS techniques. The fused coatings exhibit lower friction and better wear resistance compared with as-deposited coatings. The detailed results of each test of their coatings are discussed in this paper. © 2018 IOP Publishing Ltd.Item Effect of microwave heating on microstructure and elevated temperature adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2 coating(Elsevier B.V., 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This research reports the improvement of high-temperature sliding wear resistance of a grade 15 titanium alloy protected by an HVOF sprayed CoMoCrSi-Cr3C2 coating. The coatings have been tested in as-sprayed condition and after a post-deposition microwave heating step. The powder feedstock has been manufactured by high energy ball milling. X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) equipped with the Energy Dispersive Spectroscopy (EDS) methods were used for coatings characterization. Surface roughness, microhardness, adhesion strength, and porosity of coatings were also measured. The wear test was conducted at an applied load of l0 N and 20 N with varying temperatures of 200 °C, 400 °C, and 600 °C under dry sliding conditions. Co3Mo2Si, Co7Mo6, Mo3Si, Co3Mo, and Co2Mo3 were the intermetallic laves phases generated in the CoMoCrSi feedstock during HEBM process. The microwave-fused coating exhibited metallurgical bonding, homogeneous structure, less porosity, and greater hardness as compared to as-sprayed coating. Microwave-treated coating revealed better wear property than an as-sprayed coating. This was mainly due to the intermetallic formation and metallurgical bonding in coatings. The fused coatings exhibit tribo-oxide layers during sliding action which was the main phenomenon of improving the wear resistance of the fused composite coatings. © 2019 Elsevier B.V.Item Development and Sliding Wear Behavior of Co-Mo-Cr-Si Cladding through Microwave Heating(Springer editorial@springerplus.com, 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.The aim of the present study is to improve the sliding wear resistance of pure titanium grade-2 substrate by developing CoMoCrSi (Tribaloy T400) cladding on it by using microwave hybrid heating technique. The developed cladding is characterized by microstructural features, phase analysis, measurement of microhardness by employing a scanning electron microscope (SEM), X-ray diffraction (XRD) and Vickers microhardness. The cladding and substrate are subjected to sliding wear test against alumina counterpart at elevated temperatures under dry conditions using a pin on disc tribometer. The test is performed by varying normal load and temperatures, whereas sliding speed is maintained constant. The developed clad shown partial melting of CoMoCrSi powders and obtained sound metallurgical bonding with the substrate. The high specific energy of microwave diluted the substrate atoms into cladding region which forms Cr3C2, Co3Ti, and TiC, phases confirmed by phase analysis. The cladding obtained better porosity and microhardness are 1.5 ± 0.2% ?m and 760 ± 35 Hv respectively. The substrate exhibits low microhardness of 182 ± 25 Hv. The cladding exhibits 6 times of lower volume loss and 70.14% of less wear rate with respect to the substrate. The cladding experienced least coefficient of friction is 0.55 compared with the substrate. The worn surfaces of cladding and substrate are examined. The detailed mechanism of wear is discussed in this paper. © 2019, Springer Nature B.V.Item Comparison of Microstructural and Sliding Wear Resistance of HVOF Coated and Microwave Treated CoMoCrSi-WC + CrC + Ni and CoMoCrSi-WC + 12Co Composite Coatings Deposited on Titanium Substrate(Springer Science and Business Media B.V. editorial@springerplus.com, 2020) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi-WC + CrC + Ni and CoMoCrSi-WC + 12Co composite coatings are coated on titanium substrate by high velocity oxygen fuel method (HVOF). Prior to spraying, CoMoCrSi feedstock are processed through high energy ball milling (HEBM) in order improve the intermetallic laves phases and to reduce its particle size. The processed feedstock exhibits amorphous nature by improving laves phases and particle size of 60.12 ?m. Microwave heating energy is utilized as post heat treatment technique to improve the mechanical and metallurgical properties of as-sprayed coatings. Fused coatings reveals better properties in terms of surface roughness, porosity, microhardness and adhesion strength compared to as-sprayed coatings. Metallurgical bonding is observed in case of fused coatings due to diffusion of substrate elements. Frictional and wear behaviors have been investigated by a pin on disc apparatus at temperatures of 200 °C, 400 °C, and 600 °C under normal loads of 10 N and 20 N. Both wear trace and friction coefficients of the fused coatings are smaller than as-sprayed coatings and substrate at all test temperatures. The wear traces of fused coatings decreased with increasing the surface temperature due to the lubricant effect of cobalt oxides formed on the sliding surface. As a result, cobalt based cermet coatings are highly recommended as a durability improvement coating for the protection of sliding surface, such as high speed spindle. © 2020, Springer Nature B.V.Item Development of Self-lubricating Nickel Based Composite Clad using Microwave Heating in Improving Resistance to Wear at Elevated Temperatures(Korean Institute of Metals and Materials, 2022) Gudala, S.; Ramesh, M.R.; Srinath, M.S.This paper reports on a study of the high-temperature tribological performance of self-lubricating nickel-based composite clad. A porous and crack free clad containing matrix, reinforcement, and lubricant phase is developed on titanium 31 alloy using microwave irradiation. The microstructure of both NiCrSiB/WC and NiCrSiB/WC/Ag/BaF2 clad revealed very good metallurgical bonding with the substrate. The average microhardness of NiCrSiB/WC and NiCrSiB/WC/Ag/BaF2 clad is 710.58 HV and 650.25 HV respectively, is comparatively higher than the titanium 31 substrate (320 HV). The addition of Ag and BaF2 solid lubricants in the clad endowing clad to operate at a broad temperature range. Compared with the NiCrSiB/WC clad, solid lubricant encapsulate clad has shown very low friction coefficient and wear rates. The sliding wear characteristics of the clad were investigated by varying load and temperatures. The results revealed that oxide phases (NiO and Cr3O) and lubricant phases (Ag and BaWO4) formed at low and high temperatures are adequate to reduce delamination and material loss. Graphical abstract: [Figure not available: see fulltext.] © 2021, The Korean Institute of Metals and Materials.Item MICROSTRUCTURE AND TRIBOLOGICAL PERFORMANCE OF SELF-LUBRICATE CLADDING PRODUCED BY TUNGSTEN INERT GAS AND MICROWAVE HYBRID HEATING TECHNIQUES(World Scientific, 2022) Gudala, S.; Ramesh, M.R.; Siva Shanmugam, N.S.; Srinath, M.S.The wear reduction of moving components is highly desirable because wear limits their reliability and service life, mainly at elevated temperatures. This study produced thick clads of NiCrSiB/WC/MoS2/BaF2 by tungsten inert gas (TIG) and microwave hybrid heating (MHH) cladding techniques, which were compared for microstructural and high-temperature tribological properties. The clad samples were subjected to sliding contact using a pin on disc tribometer at 200°C, 400°C, 600°C under 20 and 40N load. The worn surface was analyzed using FESEM, XRD and three-dimensional (3D) profilometer. The experimental results revealed a significant effect of the TIG current and MHH exposure time on the microhardness value, which predominantly depends on the morphological characteristics. The average hardness of TIG clads was found to be 1.2 times higher than the MHH clad. Because of the MoS2 and BaF2 encapsulation, the continuous lubricant layer formation compensated for improved wear resistance with good reliability and longer service life. This work provides significant insights into the wear behavior of TIG and MHH clads at elevated temperatures and the prospective applications in turbines, where inadequate wear resistance of titanium alloy is the major concern for its use. © 2022 World Scientific Publishing Company.Item Microstructure and Wear Behavior of Self-Lubricating Microwave Clads Deposited on Titanium Alloy(Springer, 2022) Gudala, S.; Ramesh, M.R.; Srinath, M.S.In this work, composite clads (NiCrSiB/WC/Ag/hBN and NiCrSiB/WC/MoS2/hBN) have been successfully developed using microwave cladding technique on titanium 31 substrate. The clads were characterized by field emission scanning electron microscope (FESEM), electron backscatter diffraction (EBSD), x-Ray diffraction (XRD) analysis. The developed clads were free from porosity, defects, and other thermal distortion effects. Furthermore, due to the uniform distribution of hard phases, clads achieved uniform hardness across the clad depth. The convective currents of the molten pool improved metallurgical bonding with the substrate. Because of the volumetric heating, the deviation of microhardness values in the clad was found to be low. The tribological properties of the clads were tested against an Al2O3 counterbody using a pin on disc tribometer. The results showed that incorporating solid lubricants (Ag/hBN and MoS2/hBN) into the nickel-based alloy significantly improved tribological properties. The wear rate and coefficient of friction decreased as the temperature increased from 200 to 600 °C. It was demonstrated that anti-wear and lubricating capability of both clad could be improved at elevated temperatures by doping Ag, MoS2, and hBN solid lubricants. © 2022, ASM International.