Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Understanding of synergy in non-isothermal microwave-assisted in-situ catalytic co-pyrolysis of rice husk and polystyrene waste mixtures(Elsevier Ltd, 2022) Sridevi, V.; Suriapparao, D.V.; Tukarambai, M.; Terapalli, A.; Ramesh, R.; Sankar Rao, C.S.; Gautam, R.; Moorthy, J.V.; Suresh Kumar, C.Rice husk (RH) and polystyrene (PS) wastes were converted into value-added products using microwave-assisted catalytic co-pyrolysis. The graphite susceptor (10 g) along with KOH catalyst (5 g) was mixed with the feedstock to understand the products and energy consumption. RH promoted the char yield (20–34 wt%) and gaseous yields (16–25 wt%) whereas PS enhanced the oil yield (23–70 wt%). Co-pyrolysis synergy induced an increase in gaseous yields (14–53 wt%) due to excessive cracking. The specific microwave energy consumption dramatically decreased in co-pyrolysis (5–22 kJ/g) compared to pyrolysis (56–102 kJ/g). The pyrolysis index increased (17–445) with the increase in feedstock quantity (5–50 g). The obtained oil was composed of monoaromatics (74%) and polyaromatics (18%). The char was rich in carbon content (79.5 wt%) and the gases were composed of CO (24%), H2 (12%), and CH4 (22%). © 2022 Elsevier LtdItem Effect of dry torrefaction pretreatment of the microwave-assisted catalytic pyrolysis of biomass using the machine learning approach(Elsevier Ltd, 2022) Ramesh, R.; Suriapparao, D.V.; Sankar Rao, C.S.; Sridevi, V.; Kumar, A.This study employs the Leave-One-Out cross-validation approach to build a machine-learning model using polynomial regression to predict pyro product yield through microwave-assisted pyrolysis of sawdust over KOH catalyst and graphite powder a susceptor. The determination of coefficient (R2) validates the developed models. All the developed models achieved a high prediction accuracy with R2 > 0.93, which signifies that the experimental values are in good agreement with the predicted one. The dependence of the catalyst loading and pretreatment temperature on dominating process parameters such as heating rate, pyrolysis temperature, susceptor thermal energy, and pyro products, namely bio-oil, biochar, and biogas, are explored. The yield of biochar is reduced; however, bio-oil and biogas are enhanced as the catalyst loading increased. On the other hand, increasing the temperature of pretreated sawdust decreased bio-oil and biogas yields while increasing biochar yields. Further, microwave conversion efficiency, and susceptor thermal energy increased with increased catalyst quantity and pretreatment temperatures of sawdust. It was observed that the average heating rate was increased by increasing the catalyst quantity while maintaining the same pyrolysis time until pretreatment temperatures of 150 °C were reached, after which the heating rate dropped due to the continuous microwave energy input to the system. © 2022 Elsevier LtdItem Microwave-assisted in-situ catalytic pyrolysis of polystyrene: Analysis of product formation and energy consumption using machine learning approach(Institution of Chemical Engineers, 2022) Terapalli, A.; Kamireddi, D.; Sridevi, V.; Tukarambai, M.; Suriapparao, D.V.; Sankar Rao, C.S.; Gautam, R.; Modi, P.R.Microwave-assisted catalytic pyrolysis is a prominent technology for the production of high-quality fuel intermediates and value-added chemicals from polystyrene waste. The objectives of this study were to understand the role of catalyst (KOH) on polystyrene (PS) pyrolysis. Pyrolysis experiments were conducted using a microwave oven at a power of 450 W and a temperature of 600 °C. Graphite susceptor (10 g) was used to achieve the required pyrolysis conditions. In addition, the design of experiments (DoE) with machine learning (ML) was used to understand the loading of PS (5 g, 27.5 g, and 50 g), and KOH (5 g, 7.5 g, and 10 g). The products including oil, gas, and char were collected in every experiment. The average heating rates achieved were in the range of 30–50 °C/min. The specific microwave power (microwave power per unit mass of feedstock) decreased with an increase in PS amount from 90 to 9 W/g. However, the specific microwave energy (microwave energy per unit mass of feedstock) (27–73 kJ/g) was in line with the average heating rate. The maximum yield of pyrolysis oil was found to be 95 wt%, which was obtained with a PS:KOH ratio of 27.5 g: 7.5 g. The oil yield increased from 80 to 95 wt% when the mass of the catalyst increased from 5 to 7.5 g. On the other hand, the gas yield (3–18 wt%) varied significantly and char yield (1–2 wt%) was not influenced. The yields predicted by ML matched well with the experimental yields. This study demonstrated the potential of KOH as a catalyst for PS pyrolysis technology as the formation of aliphatic hydrocarbons in the oil fraction was significantly promoted. © 2022 The Institution of Chemical EngineersItem Synthesis of sustainable chemicals from waste tea powder and Polystyrene via Microwave-Assisted in-situ catalytic Co-Pyrolysis: Analysis of pyrolysis using experimental and modeling approaches(Elsevier Ltd, 2022) Suriapparao, D.V.; Sridevi, V.; Ramesh, R.; Sankar Rao, C.S.; Tukarambai, M.; Kamireddi, D.; Gautam, R.; Dharaskar, S.A.; Pritam, K.In the current study, catalytic co-pyrolysis was performed on waste tea powder (WTP) and polystyrene (PS) wastes to convert them into value-added products using KOH catalyst. The feed mixture influenced the heating rates (17–75 °C/min) and product formation. PS promoted the formation of oil and WTP enhanced the char formation. The maximum oil yield (80 wt%) was obtained at 15 g:5 g, and the maximum char yield (44 wt%) was achieved at 5 g:25 g (PS:WTP). The pyrolysis index (PI) increased with the increase in feedstock quantity. High PI was noticed at 25 g:5 g, and low PI was at 5 g:5 g (PS:WTP). Low energy consumption and low pyrolysis time enhanced the PI value. Significant interactions were noticed during co-pyrolysis. The obtained bio-oil was analyzed using GC–MS and a plausible reaction mechanism is presented. Catalyst and co-pyrolysis synergy promoted the formation of aliphatic and aromatic hydrocarbons by reducing the oxygenated products. © 2022 Elsevier LtdItem The effect of torrefaction temperature and catalyst loading in Microwave-Assisted in-situ catalytic Co-Pyrolysis of torrefied biomass and plastic wastes(Elsevier Ltd, 2022) Ramesh, R.; Suriapparao, D.V.; Sankar Rao, C.S.; Sridevi, V.; Kumar, A.; Shah, M.In the current study, the effect of torrefaction temperatures (125–175 °C) and catalyst quantity (5–15 g) on co-pyrolysis of torrefied sawdust (TSD) and polystyrene (PS) are investigated to obtain value-added products. The role of torrefaction in co-pyrolysis of TSD: PS was analyzed to understand the product yields, synergy, and energy consumption. As the torrefaction temperature increases, oil yield (48.3–59.6 wt%) and char yield (24.3–29 wt%) increase while gas yield (27.4–11.4 wt%) decreases. Catalytic co-pyrolysis showed a significant level of synergy when compared to non-catalytic co-pyrolysis. For the conversion (%), a positive synergy maximum (-2.6) exists at a torrefaction temperature of 175 °C and 15 g of KOH catalyst. To develop the model, polynomial regression-based machine learning was used to predict pyrolysis product yields and energy usage variables. The developed models showed significant prediction accuracy (R2 > 0.98), suggesting the experimental values and the predicted values matched well. © 2022 Elsevier LtdItem Microwave-assisted In-situ catalytic co-pyrolysis of polypropylene and polystyrene mixtures: Response surface methodology analysis using machine learning(Elsevier B.V., 2023) Kamireddi, D.; Terapalli, A.; Sridevi, V.; Tukaram Bai, M.T.; Surya, D.V.; Sankar Rao, C.S.; Jeeru, L.R.Polypropylene (PP) and Polystyrene (PS) are the major plastic fractions found in mixed plastic waste. Hence, the current study was focused to convert PP and PS into useful products via microwave-assisted pyrolysis (MAP). In addition, the understanding of feedstock conversion, product yields, and energy requirements in pyrolysis, co-pyrolysis, and catalytic co-pyrolysis was investigated. Experiments were conducted at a constant microwave power of 450 W till the reaction temperature reached up to 600 °C. When PS pyrolyzed, a heating rate of 56 °C/min resulted in 80 wt% of oil yield. Whereas PP pyrolysis produced 42 wt% of oil at a heating rate of 76 °C/min. In the PP: PS co-pyrolysis, the heating rate was decreased to 52 °C/min by yielding 51 wt% of oil. In catalytic co-pyrolysis of PP: PS with KOH resulted in variation in product yields and heating rate. An increase in PS quantity at a constant mass of PP resulted in the enhancement of oil yields from 58 to 84 wt% and a decrease in gas yields. The specific microwave power in the catalytic co-pyrolysis (7–18 W/g) is lower compared to the non-catalytic case (22–30 W/g). Whereas, the pyrolysis time in non-catalytic pyrolysis (7–11 min) is lower compared to catalytic co-pyrolysis (14–37 min). The addition of a catalyst resulted in a decrease (23–50%) in microwave conversion efficiency than that of the non-catalytic case (60–85%). The difference in predicted and actual result analysis proved co-pyrolysis synergy in product formation and energy consumption. © 2023 Elsevier B.V.Item Two-step synthesis of biochar using torrefaction and microwave-assisted pyrolysis: Understanding the effects of torrefaction temperature and catalyst loading(Elsevier B.V., 2023) Ramesh, P.; Sankar Rao, C.S.; Surya, D.V.; Sridevi, V.; Kulkarni, A.The study focused on synthesizing the biochar from sawdust using torrefaction followed by pyrolysis. Sawdust was torrefied at different temperatures (125 °C, 150 °C, and 175 °C) using a conventional hot air oven. The obtained torrefied biochar was subjected to Microwave-assisted pyrolysis at a power of 300 W for 10 min. Graphite was used as a susceptor, and KOH was used as a catalyst. The maximum biochar product yield varied from 24 to 48 wt% and increased with torrefaction temperature. The average heating rates ranged from 54.5 to 74.6 °C/min. At 10 g of KOH, higher heating rates were obtained. The pyrolysis index analyzed varied between 97.5 and 111.5 and decreased with the increase in torrefaction temperature. The obtained biochar was analyzed using SEM, BET, XRD, FTIR, ICP-OES, and Raman spectroscopy. Porous structure formation enhanced, and the concentrations of Ca, Al, and Fe decreased with the increase in torrefaction temperature. © 2023 Elsevier B.V.Item Synergistic effects and product yields in microwave-assisted in-situ co-pyrolysis of rice straw and paraffin wax(Institution of Chemical Engineers, 2024) Hamzah, H.T.; Sridevi, V.; Surya, D.V.; Ramesh, P.; Sankar Rao, C.; Palla, S.; Abdullah, T.A.Microwave-assisted pyrolysis is one of the most efficient methods for solid waste management. This study employed microwave-assisted catalytic co-pyrolysis to convert Paraffin wax (PW) and rice straw (RS) into valuable char, gas, and oil products. KOH and graphite were used as the catalyst and susceptor, respectively. The RS and PW blend served as the feedstock (with a blend ratio of 0–10 g). The yields of co-pyrolysis at different blending ratios of RS: PW exhibited variations in char content (ranging from 9.8% to 22.6% by wt.), oil production (ranging from 34.1% to 76.9% by wt.), and gas formation (ranging from 13.2% to 47.5% by wt.). The effects of the RS: PW ratio on the average heating rate, feedstock conversion, and product yields were also investigated. Analyses were performed to assess the synergistic impacts on product yields, average heating rates, and conversion factors. Notably, co-pyrolysis synergy led to increased oil and char production. Furthermore, we conducted FTIR analysis on the oil and char produced through the catalytic co-pyrolysis of RS: PW. In conjunction with co-pyrolysis synergy, the catalyst facilitated the formation of amides, alkenes, aliphatic compounds, and aromatic compounds. © 2023 The Institution of Chemical Engineers