Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Electrochemical Behaviour of ECAP-Processed AM Series Magnesium Alloy(Springer International Publishing, 2019) Gopi, K.R.; Shivananda Nayaka, H.Equal channel angular pressing (ECAP) is a technique for inducing high strain into the material to achieve ultrafine grain refinement. AM80 magnesium was processed by ECAP with processing route BC. ECAP-processed samples were tested for microstructural studies and electrochemical measurements. Potentiodynamic polarization test revealed decrease in corrosion current density due to uniform refined microstructure of the processed samples. Increment in charge transfer resistance (Rt) was observed for ECAPed samples with increase in capacitive arc diameters in Nyquist plots showing increased corrosion resistance in comparison with as-cast condition. The increment in corrosion resistance is because of grain refinement and uniform dispersal of intermetallic particles, which improved development of protective layer and bonding due to increased grain boundary density by ECAP process. © 2019, The Minerals, Metals & Materials Society.Item Effect of equal channel angular pressing on AZ31 wrought magnesium alloys(National Engg. Reaserch Center for Magnesium Alloys zhangdingfei@cqu.edu.cn, 2013) Muralidhar, A.; Narendranath, S.; Shivananda Nayaka, H.AZ31 wrought magnesium alloys are light weight materials which play an important role in order to reduces the environmental burdens in modern society because of its high strength to weight ratio, corrosion resistance, and stiffness and machinability. Applications of this material are mainly in structural component i.e., in constructions, automobile, aerospace, electronics and marine industries. In the present work, the microstructure characterization of the AZ31 alloys up to four ECAP passes at temperature of 573 K was observed for route Bc. Average grain size of the material was reduced from 31.8 ?m to 8 ?m after four ECAP passes. Mechanical properties of the alloy improved with increase in number of ECAP passes. Moreover, X-ray diffraction analysis was carried out for as received and ECAP processed material. © 2013 National Engineering Research Center for Magnesium Alloys of China, Chongqing University.Item Microstructure Evolution and Mechanical and Corrosion Behavior of Accumulative Roll Bonded Mg-2%Zn/Al-7075 Multilayered Composite(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Anne, G.; Ramesh, M.R.; Shivananda Nayaka, H.; Arya, S.B.; Sahu, S.Multilayered composite of Mg-2%Zn/Al-7075 was developed by accumulative roll bonding (ARB) of wrought Mg-2%Zn and aluminum 7075 alloy. The Mg-2%Zn/Al-7075 multilayered composite exhibited density of 2295 kg/m3 and an average grain size of 1 and 1.3 ?m in Mg-2%Zn and Al-7075 layers, respectively. A thorough microstructural characterization was performed on the composites by scanning electron microscope, electron backscatter diffraction (EBSD), transmission electron microscope and phase analysis by x-ray diffraction. In addition, mechanical properties were evaluated by microhardness and tensile tests. Corrosion behavior of the multilayered composite was examined using electrochemical polarization test. EBSD analysis showed the presence of ultrafine grains with high-angle grain boundaries. The composite exhibited a significant improvement in ultimate tensile strength (~1.82 times) and elongation (~1.5 times) as compared with Mg-2%Zn alloy, after four-pass ARB process. © 2017, ASM International.Item Wear Properties of ECAP-Processed AM80 Magnesium Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Gopi, K.R.; Shivananda Nayaka, H.; Sahu, S.AM80 magnesium alloy was subjected to equal-channel angular pressing (ECAP), and microstructural evolution was studied using scanning electron microscope (SEM). Grain size was found to decrease up to 3 µm after four passes. An increase in number of ECAP passes led to a corresponding increase in hardness of the processed samples. Unprocessed and ECAP-processed samples were subjected to wear test using pin-on-disk wear test machine to study the wear behavior. Effects of varying loads (30 and 40 N) with sliding distances (2500 and 5000 m) were studied. The results showed reduction in wear mass loss for the ECAP-processed samples in comparison with unprocessed condition. Coefficient of friction (COF) was studied for different loads, and improvement in COF values was observed for ECAP-processed samples compared to unprocessed condition. Worn surfaces were studied using SEM and energy-dispersive x-ray spectrometer, and they exhibited plastic deformation, delamination, plowing, wear debris and oxidation in the sliding direction. X-ray diffraction analysis was conducted on the worn surfaces to identify the phases. It revealed the presence of magnesium oxide and magnesium aluminum oxide which led to oxidation wear in the sliding direction. Wear mechanism was found to be abrasive and oxidation wear. © 2017, ASM International.Item Corrosion Behavior of ECAP-Processed AM90 Magnesium Alloy(Springer Verlag, 2018) Gopi, K.R.; Shivananda Nayaka, H.; Sahu, S.Magnesium AM90 alloy was subjected to equal-channel angular pressing (ECAP) using route B C. Microstructural characterization revealed refined grains having average grain size ?3?m after ECAP 4 passes. Samples were subjected to electrochemical measurements to study the corrosion behavior. Potentiodynamic polarization test showed reduced corrosion current density (Icorr) for processed samples up to ECAP 3 pass due to grain refinement. Electrochemical impedance spectroscopy showed an increase in the diameter of the capacitive arcs and charge-transfer resistance (Rt) for ECAP-processed 3 pass sample indicating the reduction in corrosion rate. Increase in corrosion resistance is due to refined microstructure and uniform distribution of secondary particles forming a protective passivation layer (Mg (OH) 2) on the sample’s surface. Immersion test indicated lower hydrogen evolution from ECAP-processed samples compared to the unprocessed condition indicating decreased corrosion rate. © 2018, King Fahd University of Petroleum & Minerals.Item Investigation of microstructure and mechanical properties of the Cu-3% Ti alloy processed by multiaxial cryo-forging(Cambridge University Press, 2018) Ramesh, S.; Shivananda Nayaka, H.; Gopi, K.R.; Sahu, S.; Kuruveri, U.B.A Cu-3%Ti (wt%) alloy was processed by multiaxial forging (MAF) at cryogenic temperature up to 3 cycles, imposing a total strain of 1.6. Microstructure and mechanical properties of the unprocessed and cryo-forged samples were analyzed. X-ray diffraction results showed deviation in peak broadening and peak intensity of the cryo-forged samples in comparison to that of unprocessed, which are due to texture modification caused by grain refinement during the MAF process. Microstructural analysis showed reduction in grain size from 80 m in the as-received condition to 250 nm after 3 cycles. Electron backscatter diffraction results indicated the transformation of high angle grain boundaries to low angle grain boundaries in all 3 cycles when compared to the as-received condition. Reduction in ductility was observed after 1 cycle, but with an increase in the number of cycles, both strength and ductility increased. After 3 cycles, ultimate tensile strength and hardness reached 1126 MPa and 427 Hv as compared to 528 MPa and 224 Hv for the as-received condition. Fractography analysis showed decrement in dimple size after 1 cycle, in comparison to that of the as-received condition. However, it kept on increasing for higher number of cycles. © © Materials Research Society 2018.Item Strength enhancement of magnesium alloy through equal channel angular pressing and laser shock peening(Elsevier B.V., 2020) Praveen, T.R.; Shivananda Nayaka, H.; Swaroop, S.; Gopi, K.R.AM80 magnesium alloy was processed by Equal Channel Angular Pressing up to 2 passes under route BC and C, to study the effect of change in microstructure. Microstructures were examined under optical microscope. Samples processed by route BC showed heterogeneous grain structure with good tensile strength compared to that processed by route C. Tensile tests of 2-pass equal channel angular pressed samples showed high tensile strength under route BC. Laser shock peening without coating was carried out on route BC sample for further grain refinement on the surface. Laser pulses with power density of 8 GW cm?2, under different percentages of cover, were used to peen the surface at high strain rate. Microstructures were analysed through scanning and transmission electron microscope, and fine grains of less than 100 nm were observed. Tensile tests indicated that the laser shock peened samples had increased strength and ductility. Fracture details from tensile tested specimens, were examined under SEM. Mixed mode of brittle and ductile fractures was observed in ECAP processed samples. Fracture surface of Laser shock peening without coating treated on equal channel angular pressed samples showed small dimples near the peened surface and intensity of dimples increased with increase in percentage of cover. Wear test was carried out on before and after Laser shock peening without coating processed samples, on pin-on-disc wear test machine. Increase in friction coefficients and wear rate was observed due to roughness induced by peening effect and it decreased after increase in sliding distance due to increase in hardness. Nano indentation experiments were carried out to examine the mechanical characterization at nano level, and it expose the effect of LSPwC in terms of increase in hardness at peened region. © 2020Item Surface modification of multi-directional forged biodegradable Mg-Zn alloy by ball burnishing process: Modeling and analysis using deep neural network(Elsevier Ltd, 2021) Ramesh, S.; Anne, G.; Bhat, N.; Aithal, G.; Shivananda Nayaka, H.; Arya, S.This research investigates the feasibility of improving surface integrity of the Mg-2%Zn alloy via a novel combined process of multidirectional forging (MDF) with ball burnishing technique. Mg-2%Zn alloy was subjected to multidirectional forging up to 5 passes at 280 °C and same sample is ball burnished with depth of press of 0.3 mm, feed of 300 mm/min and force of 250 N for 1 pass. Microstructure (optical and transmission electron microscope), phases (X ray diffraction), roughness (atomic force microscope) and mechanical properties (microhardness and tensile) were analyzed for cast, MDF processed and MDF + ball burnished samples. The study also defines a new reliability simulation framework to predict the roughness and hardness of the MDF + ball burnished samples using Deep Neural Network (DNN) approach. For the analysis, depth of press, feed and number of passes served as inputs for the DNN model. After configuring and training procedure of the model, the predicted roughness and microhardness of the MDF + ball burnished were compared with the results of experimental data. A large increase of microhardness was observed for MDF-5 + BB-1 (5 pass MDF processed Mg-2%Zn alloy + Ball burnished sample), found to be 98 Hv and surface roughness of 306 nm was achieved. According to the results, the obtained R-squared value is very close to the 99.5 percentage from the model for predicting roughness and hardness which is a promising result. Corrosion behavior of the AS-1, MDF-5 and MDF-5 + BB-1 was evaluated in Hank's balanced salt solution. Corrosion rate of the MDF-5 + BB-1 samples were found to be 0.87 mm/y which is 7 times better than that of AS-1 samples (6.10 mm/y). Grain refinement and residual stresses were higher in the MDF-5 + BB-1 sample, which helped significantly to enhance corrosion resistance. © 2021 The Society of Manufacturing Engineers