Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Development and characteristics of accumulative roll bonded Mg-Zn/Ce/Al hybrid composite(Elsevier Ltd, 2017) Anne, G.; Ramesh, M.R.; Shivananda Nayaka, H.; Arya, S.B.; Sahu, S.Accumulative roll bonding (ARB) process have been used develop Mg-2%Zn/Ce/Al hybrid composite and microstructure, mechanical and corrosion properties were investigated. The electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) revealed that the grains are significantly reduced and reaches up to 1 ?m in Mg-2%Zn layer and 1.8 ?m in Al layer having high angle misorientation of grain boundaries after subjected to 5-passes of the ARB process. The Al17Mg12, AlMg4Zn11 and Al11Ce3 intermetallic phases were observed through the XRD analysis. Mechanical properties of the hybrid composite improved with increase in the number of ARB passes which is attributed to work hardening, grain refinement and uniform distribution of Ce particles. Presence of Ce in the hybrid composite restricts the phenomenon of dynamic recrystallization and prevents the grain growth during ARB process. The corrosion rate of Mg-Zn/Ce/Al hybrid composite (0.72 mm/y) improved about 3.3 times as compared to that of Mg-2%Zn alloy (2.37 mm/y). © 2017 Elsevier B.V.Item Tribological and corrosion properties of AM70 magnesium alloy processed by equal channel angular pressing(Cambridge University Press, 2017) Gopi, K.R.; Shivananda Nayaka, H.Wear and corrosion properties of AM70 magnesium alloy subjected to equal channel angular pressing (ECAP) were investigated using pin-on-disc dry sliding wear test and electrochemical impedance spectroscopy (EIS), respectively. Wear test was conducted with 30 and 40 N loads with sliding distance of 5000 m and at a constant speed of 3 m/s. Reduced coefficient of friction (COF) and wear mass loss of ECAP processed samples showed increased wear resistance. Worn surface analysis by scanning electron microscope (SEM) showed the presence of delamination, wear debris, and plowing. Energy dispersive X-ray spectrometer (EDS) revealed the occurrence of oxidation, and the wear mechanism was identified as abrasion and oxidation wear. EIS plots showed the improvement in corrosion resistance of ECAP processed magnesium alloy compared to initial condition due to grain refinement and homogeneous distribution of secondary particles. © Materials Research Society 2017.Item Wear Properties of ECAP-Processed AM80 Magnesium Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Gopi, K.R.; Shivananda Nayaka, H.; Sahu, S.AM80 magnesium alloy was subjected to equal-channel angular pressing (ECAP), and microstructural evolution was studied using scanning electron microscope (SEM). Grain size was found to decrease up to 3 µm after four passes. An increase in number of ECAP passes led to a corresponding increase in hardness of the processed samples. Unprocessed and ECAP-processed samples were subjected to wear test using pin-on-disk wear test machine to study the wear behavior. Effects of varying loads (30 and 40 N) with sliding distances (2500 and 5000 m) were studied. The results showed reduction in wear mass loss for the ECAP-processed samples in comparison with unprocessed condition. Coefficient of friction (COF) was studied for different loads, and improvement in COF values was observed for ECAP-processed samples compared to unprocessed condition. Worn surfaces were studied using SEM and energy-dispersive x-ray spectrometer, and they exhibited plastic deformation, delamination, plowing, wear debris and oxidation in the sliding direction. X-ray diffraction analysis was conducted on the worn surfaces to identify the phases. It revealed the presence of magnesium oxide and magnesium aluminum oxide which led to oxidation wear in the sliding direction. Wear mechanism was found to be abrasive and oxidation wear. © 2017, ASM International.Item Numerical Simulation of Shot Peening Process on Equal Channel Angular Pressed Magnesium Alloy(Springer Netherlands rbk@louisiana.edu, 2018) Praveen, T.R.; Gopi, K.R.; Shivananda Nayaka, H.This paper presents the numerical simulation of inducing residual stresses on equal channel angular pressed (ECAP) magnesium alloy by shot peening process. Mg-Al-Mn (AM) series magnesium alloy was ECAP processed up to 4 passes using route BC. Microstructures were analysed and grain size reduced from 100 µm for the as-received sample to 3 µm for ECAP 4 pass sample. Tensile test was carried out and maximum tensile strength was found in ECAP 2 pass sample and decreased with higher ECAP passes. Grain refinement was characterized by optical microscopy, electron backscatter diffraction analysis (EBSD) and X-ray diffraction (XRD). Material (tensile) behaviour of 2 pass sample was implemented for finite element modelling. A finite element method was used to estimate the intensity of residual stresses developed due to shot peening in ECAP processed AM80 alloy. Simulation was done with different boundary condition such as impact velocity, geometry of shot-peen media, angle of impact and multiple impacts. The results are presented and the relationship between process parameters and the intensity of residual stresses are discussed. Increase in velocity of shot peening media showed an increase in the magnitude of residual stresses. Change in geometry of shot media altered the contact area between target and shot media during impact which influenced the magnitude of residual stresses and coverage area. The magnitude of residual stresses varied with the angle of impact and the multiple repeated impacts showed that the effective depth of residual stresses increased with the number of impacts. © 2018, Springer Science+Business Media B.V., part of Springer Nature.Item Strength enhancement of magnesium alloy through equal channel angular pressing and laser shock peening(Elsevier B.V., 2020) Praveen, T.R.; Shivananda Nayaka, H.; Swaroop, S.; Gopi, K.R.AM80 magnesium alloy was processed by Equal Channel Angular Pressing up to 2 passes under route BC and C, to study the effect of change in microstructure. Microstructures were examined under optical microscope. Samples processed by route BC showed heterogeneous grain structure with good tensile strength compared to that processed by route C. Tensile tests of 2-pass equal channel angular pressed samples showed high tensile strength under route BC. Laser shock peening without coating was carried out on route BC sample for further grain refinement on the surface. Laser pulses with power density of 8 GW cm?2, under different percentages of cover, were used to peen the surface at high strain rate. Microstructures were analysed through scanning and transmission electron microscope, and fine grains of less than 100 nm were observed. Tensile tests indicated that the laser shock peened samples had increased strength and ductility. Fracture details from tensile tested specimens, were examined under SEM. Mixed mode of brittle and ductile fractures was observed in ECAP processed samples. Fracture surface of Laser shock peening without coating treated on equal channel angular pressed samples showed small dimples near the peened surface and intensity of dimples increased with increase in percentage of cover. Wear test was carried out on before and after Laser shock peening without coating processed samples, on pin-on-disc wear test machine. Increase in friction coefficients and wear rate was observed due to roughness induced by peening effect and it decreased after increase in sliding distance due to increase in hardness. Nano indentation experiments were carried out to examine the mechanical characterization at nano level, and it expose the effect of LSPwC in terms of increase in hardness at peened region. © 2020Item Influence of Ball Burnishing Process on Equal Channel Angular Pressed Mg-Zn-Si Alloy on the Evolution of Microstructure and Corrosion Properties(Springer Science and Business Media B.V., 2021) Ramesh, S.; Anne, G.; Kumar, G.; Jagadeesh, C.; Shivananda Nayaka, H.In the present study, Mg-4Zn-1Si alloy was subjected to equal channel angular pressing (ECAP) up to 4 passes at 300 °C, followed by ball burnishing using 0.3 mm depth of press, 300 mm/min feed and 1 pass successfully. The effect of ECAP and ECAP + ball burnishing process on microstructure, mechanical properties (tensile and hardness) and corrosion behavior was systematically investigated. After 4 pass ECAP, initial coarse grains (210 ?m) were refined and average grain size is 6 ?m and after ball burnishing, the grain size is found to be 3.3 ?m. Microstructure evolution is discussed using optical images, scanning electron microscope images and transmission electron microscope images. For ECAP samples, maximum strength and hardness was recorded at 3 pass. Both strength and hardness decreased for 4 pass ECAP processed samples, even though grain size decreased, this is because of texture modification in the material. ECAP 4 pass + ball burnished samples exhibited 48.5% enhancement of microhardness as compared to 4 pass ECAP samples. Corrosion resistance of the samples decreased with increase in the number of ECAP passes, this is due to strain-induced grain refinement with more crystalline defects in samples. Combined process of ECAP and ball burnishing effectively reduces the Icorr and this consequently reduces corrosion rate of the Mg–4Zn-1Si alloy. © 2020, Springer Nature B.V.Item Effect of Equal Channel Angular Pressing on Properties Evaluation of Biodegradable Mg-Zn-Mn Alloy(Springer Science and Business Media Deutschland GmbH, 2021) Ramesh, S.; Kumar, G.; Jagadeesh, C.; Anne, G.; Shivananda Nayaka, H.Equal channel angular pressing (ECAP) was used to process Mg-4Zn-1Mn alloy at 300 °C using route Bc up to 4 pass with a cumulative strain of 3.2. Optical microscope (OM), microstructures results shows homogenized sample grain size was 260 µm, after 4 pass ECAP grain size was decreased to 6 µm. Electron back-scattered diffraction (EBSD) shows the misorientation angle converted from low-angle grain boundaries (LAGB) to high-angle grain boundaries (HAGB). Dislocation density and fine grains were observed from transmission electron microscope (TEM) images. Strength has been increased from 156 to 218 MPa and hardness increased to 68 Hv after 4 pass of ECAP. Fractography analysis revealed that dimple size decreases as ECAP passes increased. XRD analysis shows the peak broadening and intensity variation, because of grain refinement. The corrosion behavior of the homogenized and ECAP-processed samples were investigated by electrochemical tests using simulated body fluids (SBF) at 37 ± 1 °C. The lower corrosion resistance of ECAP-processed Mg-4Zn-1Mn alloy attributed to the strain-induced crystalline defects, subgrain boundaries and high-density dislocations. Enhanced strength and ductility combined with lower corrosion resistance of ECAP-processed Mg-4Zn-1Mn has greater potentials for biomedical implants. © 2021, The Author(s), under exclusive licence to Springer Nature Switzerland AG.Item Surface modification of multi-directional forged biodegradable Mg-Zn alloy by ball burnishing process: Modeling and analysis using deep neural network(Elsevier Ltd, 2021) Ramesh, S.; Anne, G.; Bhat, N.; Aithal, G.; Shivananda Nayaka, H.; Arya, S.This research investigates the feasibility of improving surface integrity of the Mg-2%Zn alloy via a novel combined process of multidirectional forging (MDF) with ball burnishing technique. Mg-2%Zn alloy was subjected to multidirectional forging up to 5 passes at 280 °C and same sample is ball burnished with depth of press of 0.3 mm, feed of 300 mm/min and force of 250 N for 1 pass. Microstructure (optical and transmission electron microscope), phases (X ray diffraction), roughness (atomic force microscope) and mechanical properties (microhardness and tensile) were analyzed for cast, MDF processed and MDF + ball burnished samples. The study also defines a new reliability simulation framework to predict the roughness and hardness of the MDF + ball burnished samples using Deep Neural Network (DNN) approach. For the analysis, depth of press, feed and number of passes served as inputs for the DNN model. After configuring and training procedure of the model, the predicted roughness and microhardness of the MDF + ball burnished were compared with the results of experimental data. A large increase of microhardness was observed for MDF-5 + BB-1 (5 pass MDF processed Mg-2%Zn alloy + Ball burnished sample), found to be 98 Hv and surface roughness of 306 nm was achieved. According to the results, the obtained R-squared value is very close to the 99.5 percentage from the model for predicting roughness and hardness which is a promising result. Corrosion behavior of the AS-1, MDF-5 and MDF-5 + BB-1 was evaluated in Hank's balanced salt solution. Corrosion rate of the MDF-5 + BB-1 samples were found to be 0.87 mm/y which is 7 times better than that of AS-1 samples (6.10 mm/y). Grain refinement and residual stresses were higher in the MDF-5 + BB-1 sample, which helped significantly to enhance corrosion resistance. © 2021 The Society of Manufacturing Engineers