Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Evaluation of properties of nonfoaming Warm mix asphalt mixtures at lower working temperatures(American Society of Civil Engineers (ASCE) onlinejls@asce.org, 2017) Shiva Kumar, G.; Suresha, S.N.Warm mix asphalt (WMA) is a green technology which has the potential to replace hot mix asphalt (HMA) because it reduces greenhouse gas emissions and energy consumption by lowering the temperature at which asphalt mixtures are produced and placed. During the design process, evaluation of the mix design and mechanical properties of WMA mixtures is necessary. Therefore, the ability to quantify compactability would be very useful. This paper presents details on the evaluation of asphalt mix design, workability, and mechanical properties of asphalt mixtures modified with nonfoaming WMA additives at lower working (mixing and compaction) temperatures. Further, it seeks to provide a wider gap between mixing and compaction temperatures to ensure that WMA mixtures are suitable for longer haul distances. Asphalt mix design properties were evaluated by the Superpave method for various design gyrations (Ndes), and workability properties were evaluated in terms of Superpave gyratory compactor (SGC) densification indices using the Bahia and locking point methods. Mechanical properties such as resistance to moisture-induced damage were evaluated by the tensile strength ratio (TSR) approach, rutting resistance was evaluated by a laboratory wheel tracking test using a wheel rut tester (WRT), and flexural fatigue characteristics were evaluated by four point bending using a repeated load testing (RLT) machine. The effects of nominal maximumaggregate size (NMAS), working temperature, and type of mixture on the properties ofWMAmixtures were investigated. The experimental results were statistically analyzed to identify the major influencing factors and their significance. © 2017 American Society of Civil Engineers.Item Evaluation of workability and mechanical properties of nonfoaming warm mix asphalt mixtures(ASTM International, 2018) Shiva Kumar, G.; Suresha, S.N.Laboratory evaluation of mix design and mechanical properties of Warm Mix Asphalt (WMA) mixtures is necessary during the design process; consequently, the ability to quantify the compactability of WMA mixtures would be very helpful. This article presents the findings of an experimental study aimed at evaluation of the influence of mixing and compaction temperature on mix design and mechanical and workability properties of nonfoaming WMA mixtures. Asphalt mix design properties were evaluated by the Marshall method and the Superpave method. Mechanical properties such as rutting resistance were evaluated by a laboratory wheel tracking test using a Wheel Rut Tester (WRT), and the resistance to moisture-induced damage was evaluated by the Tensile Strength Ratio (TSR) approach. Workability properties were evaluated in terms of Superpave Gyratory Compactor (SGC) densification indexes using the Bahia and locking point methods. Test results indicate that WMA mixtures compacted using SGC at a lower compaction temperature of 110°C, which satisfied the Voids in Total Mixture (VTM) requirement. In order to ensure the Voids in Mineral aggregate (VMA) and Voids Filled with Asphalt (VFA) requirements of WMA mixtures, compaction temperature should be restricted to 120°C. Furthermore, WMA mixtures prepared at lower compaction temperatures exhibited higher resistance to rut deformation because of higher Traffic Densification Index (TDI) values. The energy needed to compact the WMA mixtures at lower compaction temperatures was lower due to lower Compaction Densification Index (CDI) values. WMA mixtures made with surface-saturated dry aggregates and compacted at 110°C marginally fulfilled the minimum TSR requirement because of significant reduction in the Indirect Tensile Strength (ITS) values of conditioned specimen. © © 2018 by ASTM InternationalItem State of the art review on mix design and mechanical properties of warm mix asphalt(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Shiva Kumar, G.; Suresha, S.N.Warm mix asphalt (WMA) is a high-speed emerging technology of producing asphalt mixture at lower temperature with equivalent performance of hot mix asphalt (HMA). It offers benefits such as energy savings, compaction aid for stiffer mixes, reduces emission, and reduces asphalt binder aging during production. This paper is an overview of mix design concept, mix design properties and mechanical properties (moisture-induced damage, rutting resistance and fatigue life) of WMA and same was compared with the properties of control HMA mixtures. Review indicates that mix design concept of WMA is similar to that of control HMA and possesses better mix design properties. Regarding mechanical properties, WMA mixtures were found more prone to moisture-induced damage, rutting and fatigue than control HMA mixtures due to lower production temperature but similar or better resistance were noticed with the use of modified and higher grade binders, addition of anti-stripping agents (ASA) and hydrated lime (HL), use of open graded mix and inclusion of recycled asphalt pavement (RAP). Further, the effect of nominal maximum aggregate size (NMAS) and design gyration (Ndesign) on mix design, NMAS and aggregate type and its water absorption on moisture-induced damage, NMAS, wheel load, test temperature, air voids, and binder grade on rutting, and NMAS, air voids, and stress or strain levels on fatigue properties of asphalt mixtures were analysed. Results indicated that NMAS had the significant effect on moisture-induced damage, rutting resistance and fatigue life of WMA mixtures. WMA mixtures made with aggregates of higher water absorption values were more prone to moisture-induced damage and even fail to meet minimum (tensile strength ratio) TSR requirements. Results also indicated that WMA mixtures made with modified and higher grade binder grade were high rut resistant. WMA mixtures tested at high stress or strain levels shows higher fatigue damage compared to WMA mixtures tested at lower stress or strain levels. © 2018, © 2018 Informa UK Limited, trading as Taylor & Francis Group.Item Laboratory Evaluation of SMA Mixtures Made with Polymer-Modified Bitumen and Stabilizing Additives(American Society of Civil Engineers (ASCE) onlinejls@asce.org, 2019) Shiva Kumar, G.; Ravi Shankar, A.U.; Ravi Teja, B.V.S.Stone matrix asphalt (SMA) is a gap-graded mixture that consists of two parts, a high concentration coarse aggregate skeleton and a high binder content mortar. The coarse aggregate skeleton provides the mixture with stone-on-stone contact, giving it strength, while the high binder content mortar adds durability. The mortar is typically composed of fine aggregate, mineral filler, asphalt binder, and a stabilizing additive. A stabilizing additive such as natural fibers, mineral fibers, or polymers is added to SMA mixtures to prevent draindown. In addition, it has the potential of reinforcing and improving the tensile strength and cohesion of SMA mixtures. In this study, banana fiber (BF) and pelletized fiber (VP) are used as stabilizing additives to prepare SMA mixtures with conventional viscosity-graded (VG) 30 bitumen. Mixtures were prepared with different levels BF and VP content, and another mixture without any stabilizers was also prepared using polymer-modified bitumen (PMB). Superpave mix design, draindown, fatigue, rutting, workability, and moisture-induced damage properties were evaluated. Results indicated that addition of natural and pelletized fiber controls binder draindown and improves resistance to rutting, fatigue, and moisture-induced damage of SMA mixture. Further, polymer-modified SMA mixtures take less energy for densification compared to SMA mixtures with natural and pelletized fiber. Results also showed that even though polymer-modified SMA mixtures performed better, SMA mixtures with pelletized fiber provided comparable results. © 2019 American Society of Civil Engineers.Item Evaluation of Workability and Mechanical Properties of Stone Matrix Asphalt Mixtures Made With and Without Stabilizing Additives(Springer, 2020) Shiva Kumar, G.; Ravi Shankar, A.U.Stone matrix asphalt (SMA) is a gap-graded mixture which is the combination of higher concentration of coarse aggregate and binder mortar. The coarse aggregate skeleton provides the mixture with stone-on-stone contact, giving it strength, while the high binder content mortar adds durability. The mortar is typically composed of fine aggregate, mineral filler, binder, and a stabilizing additive. A stabilizing additive such as cellulose fibers, mineral fibers, or polymers is added to SMA mixtures to prevent draindown of the mastics. In addition, it has the potential of reinforcing and improving the tensile strength of SMA mixtures. This paper presents the findings of performance of SMA mixtures with and without stabilizing additive. Superpave mix design, draindown, fatigue, rutting, workability, and moisture-induced damage properties of the SMA mixtures was evaluated. Three types of stabilizing additives (B, S, and V), one nominal maximum aggregate size (NMAS) 13.0 mm, and an unmodified asphalt binder (VG-30) were used in the study. Results indicate that the addition of stabilizing additive controls binder draindown and mix design properties of SMA mixtures satisfies the IRC SP 79 requirements. Resistance to rutting, fatigue, and moisture-induced damage of SMA with stabilizing additives were higher than SMA mixture without stabilizing additive. Further, SMA mixture without stabilizing additive takes less energy for densification compared with SMA mixture with stabilizing additives. © 2019, Springer Science+Business Media, LLC, part of Springer Nature.