Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Understanding of synergy in non-isothermal microwave-assisted in-situ catalytic co-pyrolysis of rice husk and polystyrene waste mixtures(Elsevier Ltd, 2022) Sridevi, V.; Suriapparao, D.V.; Tukarambai, M.; Terapalli, A.; Ramesh, R.; Sankar Rao, C.S.; Gautam, R.; Moorthy, J.V.; Suresh Kumar, C.Rice husk (RH) and polystyrene (PS) wastes were converted into value-added products using microwave-assisted catalytic co-pyrolysis. The graphite susceptor (10 g) along with KOH catalyst (5 g) was mixed with the feedstock to understand the products and energy consumption. RH promoted the char yield (20–34 wt%) and gaseous yields (16–25 wt%) whereas PS enhanced the oil yield (23–70 wt%). Co-pyrolysis synergy induced an increase in gaseous yields (14–53 wt%) due to excessive cracking. The specific microwave energy consumption dramatically decreased in co-pyrolysis (5–22 kJ/g) compared to pyrolysis (56–102 kJ/g). The pyrolysis index increased (17–445) with the increase in feedstock quantity (5–50 g). The obtained oil was composed of monoaromatics (74%) and polyaromatics (18%). The char was rich in carbon content (79.5 wt%) and the gases were composed of CO (24%), H2 (12%), and CH4 (22%). © 2022 Elsevier LtdItem Effect of dry torrefaction pretreatment of the microwave-assisted catalytic pyrolysis of biomass using the machine learning approach(Elsevier Ltd, 2022) Ramesh, R.; Suriapparao, D.V.; Sankar Rao, C.S.; Sridevi, V.; Kumar, A.This study employs the Leave-One-Out cross-validation approach to build a machine-learning model using polynomial regression to predict pyro product yield through microwave-assisted pyrolysis of sawdust over KOH catalyst and graphite powder a susceptor. The determination of coefficient (R2) validates the developed models. All the developed models achieved a high prediction accuracy with R2 > 0.93, which signifies that the experimental values are in good agreement with the predicted one. The dependence of the catalyst loading and pretreatment temperature on dominating process parameters such as heating rate, pyrolysis temperature, susceptor thermal energy, and pyro products, namely bio-oil, biochar, and biogas, are explored. The yield of biochar is reduced; however, bio-oil and biogas are enhanced as the catalyst loading increased. On the other hand, increasing the temperature of pretreated sawdust decreased bio-oil and biogas yields while increasing biochar yields. Further, microwave conversion efficiency, and susceptor thermal energy increased with increased catalyst quantity and pretreatment temperatures of sawdust. It was observed that the average heating rate was increased by increasing the catalyst quantity while maintaining the same pyrolysis time until pretreatment temperatures of 150 °C were reached, after which the heating rate dropped due to the continuous microwave energy input to the system. © 2022 Elsevier LtdItem Microwave-assisted In-situ catalytic co-pyrolysis of polypropylene and polystyrene mixtures: Response surface methodology analysis using machine learning(Elsevier B.V., 2023) Kamireddi, D.; Terapalli, A.; Sridevi, V.; Tukaram Bai, M.T.; Surya, D.V.; Sankar Rao, C.S.; Jeeru, L.R.Polypropylene (PP) and Polystyrene (PS) are the major plastic fractions found in mixed plastic waste. Hence, the current study was focused to convert PP and PS into useful products via microwave-assisted pyrolysis (MAP). In addition, the understanding of feedstock conversion, product yields, and energy requirements in pyrolysis, co-pyrolysis, and catalytic co-pyrolysis was investigated. Experiments were conducted at a constant microwave power of 450 W till the reaction temperature reached up to 600 °C. When PS pyrolyzed, a heating rate of 56 °C/min resulted in 80 wt% of oil yield. Whereas PP pyrolysis produced 42 wt% of oil at a heating rate of 76 °C/min. In the PP: PS co-pyrolysis, the heating rate was decreased to 52 °C/min by yielding 51 wt% of oil. In catalytic co-pyrolysis of PP: PS with KOH resulted in variation in product yields and heating rate. An increase in PS quantity at a constant mass of PP resulted in the enhancement of oil yields from 58 to 84 wt% and a decrease in gas yields. The specific microwave power in the catalytic co-pyrolysis (7–18 W/g) is lower compared to the non-catalytic case (22–30 W/g). Whereas, the pyrolysis time in non-catalytic pyrolysis (7–11 min) is lower compared to catalytic co-pyrolysis (14–37 min). The addition of a catalyst resulted in a decrease (23–50%) in microwave conversion efficiency than that of the non-catalytic case (60–85%). The difference in predicted and actual result analysis proved co-pyrolysis synergy in product formation and energy consumption. © 2023 Elsevier B.V.Item Effective electronic waste valorization via microwave-assisted pyrolysis: investigation of graphite susceptor and feedstock quantity on pyrolysis using experimental and polynomial regression techniques(Springer, 2024) Mistry, C.; Surya, D.V.; Ramesh, R.; Basak, T.; Kumar, P.S.; Sankar Rao, C.S.; Gautam, R.; Sridhar, P.; Choksi, H.; Remya, N.Waste printed circuit board (WPCB) was subjected to microwave-assisted pyrolysis (MAP) to investigate the energy and pyrolysis products. In MAP, pyrolysis experiments were conducted, and the effects of WPCB to graphite mass ratio on three-phase product yields and their compositions were analyzed. In addition, the role of the initial WPCB mass (10, 55, and 100 g) and susceptor loading (2, 22, and 38 g) on the quality of product yield was also evaluated. By using design of experiments, the effects of graphite susceptor addition and WPCB feedstock quantity was investigated. A significant liquid yield of 38.2 wt.% was achieved at 38 g of graphite and 100 g of WPCB. Several other operating parameters, including average heating rate, pyrolysis time, microwave energy consumption, specific microwave power used, and product yields, were optimized for the MAP of WPCB. Pyrolysis index (PI) was calculated at the blending of fixed quantity WPCB (100 g) and various graphite quantities in the following order: 2 g (21) > 20 g (20.4) > 38 g (19.5). The PI improved by increasing the WPCB quantity (10, 55, and 100 g) with a fixed quantity of graphite. This work proposes the product formation and new reaction pathways of the condensable compounds. GC–MS of the liquid fraction from the MAP of WPCBs without susceptor resulted in the generation of phenolic with 46.1% relative composition. The addition of graphite susceptor aided in the formation of phenolic and the relative composition of phenolics was found to be 83.6%. The area percent of phenol increased from 42.8% (without susceptor) to 78.6% (with susceptor). Without a susceptor, cyclopentadiene derivative was observed in a very high composition (~ 31 area %). © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2023.