Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Effect of dry torrefaction pretreatment of the microwave-assisted catalytic pyrolysis of biomass using the machine learning approach(Elsevier Ltd, 2022) Ramesh, R.; Suriapparao, D.V.; Sankar Rao, C.S.; Sridevi, V.; Kumar, A.This study employs the Leave-One-Out cross-validation approach to build a machine-learning model using polynomial regression to predict pyro product yield through microwave-assisted pyrolysis of sawdust over KOH catalyst and graphite powder a susceptor. The determination of coefficient (R2) validates the developed models. All the developed models achieved a high prediction accuracy with R2 > 0.93, which signifies that the experimental values are in good agreement with the predicted one. The dependence of the catalyst loading and pretreatment temperature on dominating process parameters such as heating rate, pyrolysis temperature, susceptor thermal energy, and pyro products, namely bio-oil, biochar, and biogas, are explored. The yield of biochar is reduced; however, bio-oil and biogas are enhanced as the catalyst loading increased. On the other hand, increasing the temperature of pretreated sawdust decreased bio-oil and biogas yields while increasing biochar yields. Further, microwave conversion efficiency, and susceptor thermal energy increased with increased catalyst quantity and pretreatment temperatures of sawdust. It was observed that the average heating rate was increased by increasing the catalyst quantity while maintaining the same pyrolysis time until pretreatment temperatures of 150 °C were reached, after which the heating rate dropped due to the continuous microwave energy input to the system. © 2022 Elsevier LtdItem Microwave-assisted in-situ catalytic pyrolysis of polystyrene: Analysis of product formation and energy consumption using machine learning approach(Institution of Chemical Engineers, 2022) Terapalli, A.; Kamireddi, D.; Sridevi, V.; Tukarambai, M.; Suriapparao, D.V.; Sankar Rao, C.S.; Gautam, R.; Modi, P.R.Microwave-assisted catalytic pyrolysis is a prominent technology for the production of high-quality fuel intermediates and value-added chemicals from polystyrene waste. The objectives of this study were to understand the role of catalyst (KOH) on polystyrene (PS) pyrolysis. Pyrolysis experiments were conducted using a microwave oven at a power of 450 W and a temperature of 600 °C. Graphite susceptor (10 g) was used to achieve the required pyrolysis conditions. In addition, the design of experiments (DoE) with machine learning (ML) was used to understand the loading of PS (5 g, 27.5 g, and 50 g), and KOH (5 g, 7.5 g, and 10 g). The products including oil, gas, and char were collected in every experiment. The average heating rates achieved were in the range of 30–50 °C/min. The specific microwave power (microwave power per unit mass of feedstock) decreased with an increase in PS amount from 90 to 9 W/g. However, the specific microwave energy (microwave energy per unit mass of feedstock) (27–73 kJ/g) was in line with the average heating rate. The maximum yield of pyrolysis oil was found to be 95 wt%, which was obtained with a PS:KOH ratio of 27.5 g: 7.5 g. The oil yield increased from 80 to 95 wt% when the mass of the catalyst increased from 5 to 7.5 g. On the other hand, the gas yield (3–18 wt%) varied significantly and char yield (1–2 wt%) was not influenced. The yields predicted by ML matched well with the experimental yields. This study demonstrated the potential of KOH as a catalyst for PS pyrolysis technology as the formation of aliphatic hydrocarbons in the oil fraction was significantly promoted. © 2022 The Institution of Chemical EngineersItem Prosopis juliflora valorization via microwave-assisted pyrolysis: Optimization of reaction parameters using machine learning analysis(Elsevier B.V., 2023) Suriapparao, D.V.; Rajasekhar Reddy, B.R.; Sankar Rao, C.S.; Jeeru, L.R.; Kumar, T.H.Microwave power and pyrolysis temperature are essential parameters in optimizing the bio-oil yield and quality in microwave pyrolysis. This study focused on understanding the interactions between the microwave power/heating rate and pyrolysis temperature in microwave-assisted pyrolysis of Prosopis juliflora. For optimum bio-oil yield, a discrete set of microwave powers (280 W, 420 W, and 560 W) and pyrolysis temperatures (200 °C, 350 °C, and 500 °C) were selected. A central composite design (CCD) was adopted to analyze the effect of microwave power and the pyrolysis temperature on product yields, heating rate, microwave conversion efficiency, and heat losses in pyrolysis. Moreover, the effect of heating rate, reaction time, specific microwave power, specific microwave energy, and conductive heat loss on gas, char, and liquid yields was evaluated using statistical machine learning techniques. Moreover, a new parameter, pyrolysis index, is calculated under different conditions to understand the extent of pyrolysis intensity using pyrolysis time, heating value, feedstock mass and conversion, and microwave energy conversion. The yields of bio-oil, biochar, and gas were 25–40 wt%, 25–35 wt%, and 35–40 wt% at different experimental conditions. Bio-oil consists of a mix of organic compounds with methoxy phenols at high selectivity, and the calorific value of bio-oil was in the range of 26–28 MJ/kg. Carbon number analysis revealed higher presence of C5–C9 compounds. This study shows the role of machine learning in understanding the effect of various parameters effectively and optimizing the experimental conditions accordingly. © 2022 Elsevier B.V.Item Microwave-assisted In-situ catalytic co-pyrolysis of polypropylene and polystyrene mixtures: Response surface methodology analysis using machine learning(Elsevier B.V., 2023) Kamireddi, D.; Terapalli, A.; Sridevi, V.; Tukaram Bai, M.T.; Surya, D.V.; Sankar Rao, C.S.; Jeeru, L.R.Polypropylene (PP) and Polystyrene (PS) are the major plastic fractions found in mixed plastic waste. Hence, the current study was focused to convert PP and PS into useful products via microwave-assisted pyrolysis (MAP). In addition, the understanding of feedstock conversion, product yields, and energy requirements in pyrolysis, co-pyrolysis, and catalytic co-pyrolysis was investigated. Experiments were conducted at a constant microwave power of 450 W till the reaction temperature reached up to 600 °C. When PS pyrolyzed, a heating rate of 56 °C/min resulted in 80 wt% of oil yield. Whereas PP pyrolysis produced 42 wt% of oil at a heating rate of 76 °C/min. In the PP: PS co-pyrolysis, the heating rate was decreased to 52 °C/min by yielding 51 wt% of oil. In catalytic co-pyrolysis of PP: PS with KOH resulted in variation in product yields and heating rate. An increase in PS quantity at a constant mass of PP resulted in the enhancement of oil yields from 58 to 84 wt% and a decrease in gas yields. The specific microwave power in the catalytic co-pyrolysis (7–18 W/g) is lower compared to the non-catalytic case (22–30 W/g). Whereas, the pyrolysis time in non-catalytic pyrolysis (7–11 min) is lower compared to catalytic co-pyrolysis (14–37 min). The addition of a catalyst resulted in a decrease (23–50%) in microwave conversion efficiency than that of the non-catalytic case (60–85%). The difference in predicted and actual result analysis proved co-pyrolysis synergy in product formation and energy consumption. © 2023 Elsevier B.V.Item Utilizing support vector regression modeling to predict pyro product yields from microwave-assisted catalytic co-pyrolysis of biomass and waste plastics(Elsevier Ltd, 2023) Ramesh, P.; Sankar Rao, C.S.; Surya, D.V.; Kumar, A.; Basak, T.The rise in plastic waste production has led to the development of co-pyrolysis of waste plastics and biomass as a potential solution. This process converts waste into valuable resources, including chemicals and pollutant-absorbing materials. Accurately predicting product yields is crucial and involves considering feedstock characteristics and pyrolysis conditions. No previous work on machine learning (ML) predicts pyro-products considering catalyst and blend as input features. This study used a support vector machine (SVM) to predict pyro-product yields from microwave-assisted co-pyrolysis of biomass and plastics. SVM models were trained, validated, and then applied to new data. The results showed high predictive accuracy, with R2 values of 0.96, 0.93, and 0.91 for bio-oil, biochar, and biogas, respectively. The SVM model demonstrated strong predictive capabilities, indicating effective generalization ability based on statistical parameters. Additionally, SVM models incorporating all features performed better than those based on 'elementary analysis (EA)' and 'proximate analysis (PA)' alone. The pearson correlation coefficient (PCC) approach assessed the correlation between input features to remove highly correlated variables. The partial dependence analysis reveals the individual effects of influential factors and their interactions in the co-pyrolysis process, highlighting significant features like carbon, hydrogen, ash, volatile matter, and nitrogen content that influence oil, char, and gas yields, thereby providing valuable insights for optimization strategies in co-pyrolysis. © 2023 Elsevier LtdItem A review on the role of various machine learning algorithms in microwave-assisted pyrolysis of lignocellulosic biomass waste(Academic Press, 2024) Mafat, I.H.; Surya, D.V.; Sankar Rao, C.S.; Kandya, A.; Basak, T.The fourth industrial revolution will heavily rely on machine learning (ML). The rationale is that these strategies make various business operations in many sectors easier. ML modeling is the discovery of hidden patterns between multiple process parameters and accurately predicting the test values. ML has provided a wide range of applications in Chemical Engineering. One major application of ML can be found in the microwave-assisted pyrolysis (MAP) of lignocellulose bio-waste. MAP is an energy-efficient technology to obtain high-saturated hydrogen-rich liquid fuels. The main focus of this review study is understanding the utilization of various types of ML algorithms, including supervised and unsupervised techniques in microwave-assisted heating techniques for diverse biomass feedstocks, including waste materials like used tea powder, wood blocks, kraft lignin, and others. In addition to developing effective ML-based models, alternative traditional modeling approaches are also explored. In addition to various thermochemical conversion processes for biomass, MAP is also briefly reviewed with several case studies from the literature. The conventional modeling methodology for biomass pyrolysis with microwave heating is also discussed for comparison with ML-based modeling methodologies. © 2024 Elsevier LtdItem Development of machine learning model for the prediction of selectivity to light olefins from catalytic cracking of hydrocarbons(Elsevier Ltd, 2025) Mafat, I.H.; Sharma, S.K.; Surya, D.V.; Sankar Rao, C.S.; Maity, U.; Barupal, A.; Jasra, R.Light olefins are the primary building block for the production of petrochemicals and polymers. Light olefins are largely produced from steam/catalytic cracking of naphtha or ethane/propane. Selectivity to light olefins is significantly dependent on the reaction conditions. In this article, several machine learning models are developed and tested to predict the selectivity of ethylene and propylene using seven input features. For this study, a total of eight ML models consisting of adaptive boost, extreme gradient boost, categorical boost, light gradient boost, decision tree with bagging, random forest, k-nearest neighbour, and artificial neural models are developed. The extreme gradient boost model gave the highest prediction accuracy for the ethylene selectivity, while the light gradient boost gave the highest R2 for the propylene selectivity. The SHAP analysis showed the input parameter's importance ranking for ethylene predictions as temperature > number of carbon atoms > Si/Al ratio > acidity > weight hourly space velocity > effect of diluent > number of hydrogen atoms. The importance ranking of input parameters for propylene selectivity was observed as weight hourly space velocity > acidity > temperature > Si/Al ratio > effect of diluent > number of carbon atoms > number of hydrogen atoms. © 2024 Elsevier Ltd