Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Rokkala, U.Subject: search.filters.subject.Friction

Search Results

Now showing 1 - 6 of 6
  • No Thumbnail Available
    Item
    Tailoring surface characteristics of bioabsorbable Mg-Zn-Dy alloy using friction stir processing for improved wettability and degradation behavior
    (Elsevier Editora Ltda, 2021) Rokkala, U.; Bontha, S.; Ramesh, M.R.; Balla, V.K.; Srinivasan, A.; Kailas, S.V.
    Magnesium (Mg) and its alloys are currently under consideration for use as temporary implants. However, early degradation and maintaining mechanical integrity is a significant concern. Surface modification techniques are used to improve mechanical and corrosion properties of Mg based alloys. In the present study, friction stir processing (FSP) was used to tailor the surface characteristics of Mg-1Zn-2Dy (wt.%) alloy for temporary implant applications. The FSPed alloy was characterized using EBSD to understand the influence of FSP on crystallographic texture, grain size and grain boundaries and thereby their effect on corrosion, wettability and hardness. Results showed that the grain size of stir zone (SZ) was refined to less than 3 ?m, as a result of dynamic recrystallization (DRX) during FSP and the FSPed alloy exhibited better wettability than as-cast alloy. An increase in the hardness (11.7%) and elastic modulus (6.84%) of FSPed alloy were also observed. Electrochemical corrosion and weight loss methods were conducted in Dulbecco's Modified Eagle's Medium (DMEM) with, 10% Fetal Bovine Serum (FBS) physiological solution. The lower degradation rate (0.72 mm/yr) of FSPed alloy has been attributed to the fine grains and evenly distributed secondary phase particles. Further, the influence of grain boundary characteristics and crystallographic texture on the corrosion behavior have been investigated. © 2021 The Author(s).
  • No Thumbnail Available
    Item
    Comparative investigation of coating and friction stir processing on Mg-Zn-Dy alloy for improving antibacterial, bioactive and corrosion behaviour
    (Elsevier B.V., 2021) Rokkala, U.; Jana, A.; Bontha, S.; Ramesh, M.R.; Balla, V.K.
    Magnesium based alloys are well-known materials for temporary implant applications. However, failures due to early degradation and bacterial infection are limiting their applications. To overcome these problems, in the present work a Mg-Zn-Dy alloy based composite surface was prepared using coating and friction stir processing (FSP) techniques. Herein, hydroxyapatite (HA) and silver (Ag) particles were deposited on Mg-Zn-Dy alloy to obtain HA and Ag coated surface (C-HAg). Later, FSP was carried out on the C-HAg surface to develop a Mg-Zn-Dy alloy based composite surface (F-HAg). Field emission scanning electron microscope (FESEM) and energy dispersive X-ray analysis (EDS) confirm the mixing of HA and Ag particles with the Mg-Zn-Dy substrate. Antibacterial studies reveal that both C-HAg and F-HAg samples inhibit Escherichia coli and Staphylococcus aureus bacteria. In vitro cytotoxicity study indicates that the both samples are non-toxic in nature. Results of in vitro corrosion study reveal a significant reduction (72%) in corrosion rate of F-HAg sample when compared to C-HAg sample. The F-HAg samples showed simultaneous improvement in corrosion resistance and antibacterial properties with good biocompatibility. The results of this study indicate that the developed composite surface is a promising material for antibacterial and biodegradable implant applications. © 2021 Elsevier B.V.
  • No Thumbnail Available
    Item
    Influence of friction stir processing on microstructure, mechanical properties and corrosion behaviour of Mg-Zn-Dy alloy
    (Springer, 2023) Rokkala, U.; Bontha, S.; Ramesh, M.R.; Balla, V.K.
    In the present study, friction stir processing (FSP) was carried out on as-cast Mg-Zn-Dy alloy to tailor grain size and texture which alter the mechanical properties and corrosion behaviour. The grain size of the as-cast alloy was reduced from 60 ± 2 µm to 3 ± 0.1 µm after FSP due to dynamic recrystallization. The effect of grain size, crystallographic orientation and fine precipitates on mechanical properties were investigated using field emission scanning electron microscope (FESEM) and electron back scattered diffraction (EBSD). The ultimate tensile strength, yield strength, % elongation and hardness of FSPed alloy improved by 55%, 60%, 53% and 46% when compared to as-cast alloy. The FSPed Mg-Zn-Dy alloy exhibited a 79% decrease in corrosion rate when compared to as-cast alloy which can be attributed to grain refinement, uniform distribution of secondary precipitates and strong basal texture. The surface of FSPed sample after immersion corrosion exhibited calcium phosphate rich minerals which help in apatite formation on the sample surface. Cytotoxicity studies using MTT assay revealed more than 80% cell viability for both as-cast and FSPed alloy illustrating non-toxic nature of both the samples. The results of this study indicate that FSPed Mg-Zn-Dy alloy is a potential material for biodegradable implants due to its high strength, corrosion resistance and biocompatibility. Graphical Abstract: [Figure not available: see fulltext.]. © 2023, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.
  • No Thumbnail Available
    Item
    Comparative Study of Plasma Spray and Friction Stir Processing on Wear Properties of Mg-Zn-Dy Alloy
    (Springer, 2024) Rokkala, U.; Gudala, S.; Ramesh, M.R.
    Mg alloys are becoming increasingly popular as lightweight materials in recent years. Wear resistance, on the other hand, is a severe issue with Mg alloys. Plasma spray and friction stir processing (FSP) are being investigated in this context for developing composite surfaces with improved surface characteristics. Scanning electron microscopy (SEM), energy dispersive spectroscopy, and x-ray diffraction are used to examine the microstructural changes and phase changes of all materials. After FSP, SEM analysis indicated that the coated particles were equally dispersed throughout the Mg matrix. The composite samples had the lowest wear rate as compared to other samples, according to the wear tests. In comparison to AC, the F-1 sample surface has much higher wear resistance. As a consequence, the findings of this investigation for the F-1 sample appear encouraging for biological wear resistant applications. © ASM International 2023.
  • No Thumbnail Available
    Item
    Effect of dilution on the microstructure and high-temperature wear resistance of self-lubricating nickel alloy claddings
    (SAGE Publications Inc., 2024) Gudala, S.; Rokkala, U.; Rao Medabalimi, S.; M.r, R.; Konovalov, K.S.
    In this study, the impact of substrate dilution on the microstructure and tribological properties of tungsten inert gas (TIG)-deposited self-lubricating claddings was investigated. The dilution of Ti content on cladding increased as the TIG current increased, and the microhardness of the cladding decreased. The content of intermetallic phases such as TiNi and TiC increased with the increase in TIG current. The tribological studies revealed that coating dilution at higher TIG currents has prominent effects on wear behaviour at elevated temperatures. In both clads, the percentage decrease in hardness from higher TIG current to lower TIG current was noted as 31%. The higher dilution of Ti content in the cladding was found to be beneficial in tribological studies performed, especially at higher temperatures (≥400). Also, solid lubricants such as MoS2 and BaF2 encapsulation in the nickel alloy were found to be beneficial at both low and high temperatures. © The Author(s) 2024.
  • No Thumbnail Available
    Item
    Multi-step fabrication of bioactive Mg–Zn–Dy–AlO3/HA composites: exploring the synergistic effects of plasma spray and friction stir processing
    (Springer, 2024) Rokkala, U.; Bontha, S.; Ramesh, M.R.; Balla, V.K.
    Magnesium (Mg) alloys are gaining more attention in recent times as biodegradable materials. However, two major problems with Mg alloy implants are bacterial infections and poor corrosion resistance. In this context, a composite surface (Mg–Zn–Dy–Al2O3/HA) is developed using surface modification techniques. First, Al2O3 + HA composite powder is coated on Mg–Zn–Dy alloy to attain coated surface (C-AHa). Next, the C-AHa surface is subjected to friction stir processing to develop composite surface (F-AHa). Microstructural characterization reveals that, the Al2O3 + HA particles were distributed evenly into the Mg–Zn–Dy substrate. Antimicrobial activities against Escherichia coli and Staphylococcus aureus reveal low adhesion of bacteria on the F-AHa sample surface due to low surface energy (37.83 ± 0.22 mN/m) and low surface roughness (0.36 ± 0.1 µm). Further, the cytotoxicity tests confirm that the F-AHa sample shows significant improvement in cell viability (98%) after 7 days and non-toxic against the mouse osteoblast cells. In Vitro corrosion study observations demonstrate that the corrosion rate for the F-AHa sample is decreased by 72% compared to the C-AHa sample. Thus, the results of this study for the fabricated composites are promising for antimicrobial, biocompatible and bioabsorbable temporary implants. © The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature 2024.