Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Durability studies on eco-friendly concrete mixes incorporating steel slag as coarse aggregates(Elsevier Ltd, 2016) Palankar, N.; Ravi Shankar, A.U.; Mithun, B.M.The present study discusses the durability performance of alkali activated concrete mixes containing steel slag as coarse aggregates. Steel slag aggregates, a waste product obtained from iron and steel industry are incorporated as coarse aggregates in alkali activated slag concrete (AASC) and alkali activated slag fly ash concrete (AASFC) by replacing traditional natural aggregates. The mix design for AASC and AASFC mixes are optimised to obtain sufficient strength for structural purposes and then steel slag coarse aggregates are incorporated at different replacement levels (0%, 50% and 100% by volume of total coarse aggregate content). Durability properties such as long term ageing performance, water absorption, volume of permeable voids, resistance to sulphuric acid attack and resistance to magnesium sulphate attack are studied in detail and compared with conventional Ordinary Portland Cement Concrete (OPCC). The ecological and economical analysis of concrete mixes is also carried out. It was found that the AASC and AASFC mixes displayed better durability performance as compared to OPCC. The inclusion of steel slag aggregates slightly reduced the durability performance of AASC and AASFC mixes. The AASC and AASFC with steel slag aggregates displayed lower energy requirement and lower production cost as compared to OPCC, thus proving it to be eco-friendly. © 2016 Elsevier Ltd. All rights reserved.Item Investigations on Alkali-Activated Slag/Fly Ash Concrete with steel slag coarse aggregate for pavement structures(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2017) Palankar, N.; Ravi Shankar, A.U.; Mithun, B.M.The present investigation is conducted to evaluate the effect of steel slag coarse aggregates on mechanical properties and fatigue behaviour of Alkali-Activated Slag Fly Ash Concrete (AASFC) mixes. AASFC mixes were prepared with steel slag coarse aggregates by replacing natural coarse aggregates at various replacement levels (0, 25, 50, 75 and 100% by volume). Various mechanical properties and fatigue performance were tested and compared with conventional Portland concrete. The incorporation of steel slag aggregates resulted in decrease in mechanical strength of AASFC mixes. The fatigue lives of AASFC mixes containing steel slag were found to be lower than AASFC with natural coarse aggregates. Two-parameter Weibull distribution was used for statistical analysis of fatigue data and it was observed that the fatigue data of concrete mixes can be approximately modelled using Weibull distribution. Steel slag aggregates reported acceptable performance in AASFC mixes for its use in pavement quality concrete. © 2015 Informa UK Limited, trading as Taylor & Francis Group.Item A study on initial setting time and the mechanical properties of AASC using the PS ball as fine aggregate(Springer, 2019) Talkeri, A.H.; Ravi Shankar, A.U.India is the second largest producer of cement in the world with an annual production of 455 Million Tonnes (MT) which is expected to reach up to 550MT by 2020. In India, the increased demand for cement in the construction industry is required to meet the needs of infrastructure development. However, the production of Portland cement releases significant amounts of CO2 to the atmosphere. Therefore, it is necessary to look for sustainable solutions for concrete production by the use of supplementary cementitious materials. The alternative replacement for Ordinary Portland Cement (OPC) can be Ground Granulated Blast Furnace Slag (GGBS), Fly-ash, Silica fume, Rice-husk ash, which is the various industrial by-products. In this present work, an attempt was made to develop Alkali Activated Slag Concrete (AASC) using Precious Slag (PS) ball as fine aggregate. The development of AASC was made with GGBS as the principal binder. Mixes were developed with binder content 443 kg/m3, Sodium Silicate (SS)/Sodium Hydroxide (SH) ratio of 1 and their performance when exposed to ambient temperature were studied. Alkali binder ratio (0.3) with 8, 10, 12 and 14M NaOH was selected for all the AASC mixes. The test results showed that the slump values for the different mixes satisfying the MoRTH guidelines for concrete pavements. The AASC mixes have higher compressive strength ranging between 41–64 MPa. The fatigue life of the AASC mix was has improved by the addition of PS ball, at the higher concentration of NaOH. © 2019, Chinese Society of Pavement Engineering. Production and hosting by Springer Nature.Item Alkali activated slag-fly ash concrete incorporating precious slag as fine aggregate for rigid pavements(Chang'an University, 2022) Talkeri, A.; Ravi Shankar, A.U.This study aims to develop the alkali activated slag-fly ash concrete (AASFC) using precious slag (PS) ball as the fine aggregate. The slag-fly ash proportion, sodium silicate/sodium hydroxide (SS/SH) ratio and sodium hydroxide concentration are the prime variables. The fresh concrete properties like workability, setting time and the hardened concrete properties of AASFC developed under ambient curing were analyzed and similar way by replacing with fly ash (FA). The sodium hydroxide concentration of 8 M, 10 M and 12 M, SS/SH ratio of 1.0, 1.5 and 2.0, alkaline liquid to binder ratio of 0.35 and variation in slag-fly ash proportion as major inputs for mix design. The test results showed that, the fresh state of AASFC blend has a shorter setting time of 12–16 min, because of calcium mineral from the FA, the workability and setting time of AASFC mix was enhanced by the addition of the tri-sodium phosphate as a retarder. At the higher SS/SH extent, the workability and setting time exaggerated, whereas the increased FA content and sodium hydroxide concentration had a greater influence on the fresh state of concrete. Also, the sodium hydroxide concentration, SS/SH ratio and slag-fly ash proportion are the most inducing parameters on the workability, setting time and strength parameters of AASFC. © 2021 The AuthorsItem Optimisation of recycled concrete aggregates for cement-treated bases by response surface method(Taylor and Francis Ltd., 2023) Chiranjeevi, K.; Kumar, D.H.; Srinivasa, A.S.; Ravi Shankar, A.U.Sustainability is a primary concern that needs to be addressed since infrastructure development requires significant natural resources. Using Recycled Concrete Aggregates (RCA) for road construction has numerous benefits in saving natural resources and the environment. In the present investigation, the demolition waste is being used for road construction, partially/fully replacing natural aggregates. The Cement Treated Recycled Concrete Aggregate (CTRCA) specimens were prepared at 3%, 5%, and 7% cement with various blends of RCA and Natural Coarse Aggregates (NCA) ranging from 0 to 100%. The strength characteristics in terms of Unconfined Compressive Strength (UCS), Flexural Strength (FS), Elastic Modulus, Indirect Tensile Strength (ITS) and durability tests were conducted on cured samples. Microstructural analysis using Scanning Electronic Microscope (SEM) revealed that the pores and cracks in the old mortar have a detrimental influence on the mechanical properties of CTRCA mixes. However, Energy Dispersive Spectroscopy (EDS) and durability tests have shown positive results. The Response Surface Method (RSM) was utilised to optimise the RCA and cement content in CTRCA mixes. The research resulted in the maximum possible RCA of up to 70% with a cement content of 5.8%, which met the Indian Road Congress (IRC) specifications for Cement Treated Bases (CTB). © 2023 Informa UK Limited, trading as Taylor & Francis Group.Item Laboratory investigation on cement-treated recycled concrete aggregate bases for flexible pavements(Elsevier Ltd, 2023) Chiranjeevi, K.; Hemanth Kumar, D.; Yathish, R.G.; Ravi Shankar, A.U.India's economy is progressing fast, and many infrastructure development programs are going on. Especially the road network expansion is going on many folds. As a result, natural coarse aggregates are getting depleted, which has an impact on environmental sustainability. Utilizing the resources from the many aged and demolished structures will be cost-effective and solve the disposal problem of these wastes. India's government insists on using marginal material, demolished waste, or recycled aggregates as alternative materials for road construction. New codes developed by IRC and MoRTH recommend Cement Treated Bases (CTB) and Cement Treated Sub-Bases for pavement lower layers. In light of this, the present study attempts to utilize Recycled Concrete Aggregates (RCA) obtained from construction and demolition (C&D) waste in the CTB. The efficiency of RCA was checked at various replacement levels ranging from 0% to 100% with cement stabilization of 3%, 5%, and 7%. The strength properties like Unconfined Compressive Strength (UCS), Flexural Strength and durability were evaluated. The microstructural characteristics and elemental analysis of the cement treated recycled concrete aggregate mixtures were examined. The research yielded the highest potential RCA of up to 50% with a cement content of 5%, meeting the Indian Road Congress (IRC) criteria for CTB. © 2023Item Optimization and Characterization of Ferrochrome and Recycled Concrete Aggregate Mixes for Pavement Base Layers(American Society of Civil Engineers (ASCE), 2025) Chiranjeevi, K.; Kumar, D.H.; Yatish, R.G.; Mulangi, R.H.; Ravi Shankar, A.U.Utilizing alternate aggregates is crucial for conserving resources, promoting sustainability, and managing waste effectively. The focus of the current study was the utilization of ferrochrome aggregate (FCA) and recycled concrete aggregate (RCA) in cement-treated base layers with the objective of entirely replacing natural coarse aggregate (NCA). The study meticulously prepared cement treated recycled and ferrochrome aggregate (CTRFA) specimens with 3%, 5%, and 7% cement content. These specimens incorporated varying blends of RCA and FCA, ranging from 0% to 100%. Response surface method (RSM) was used to optimize the mixes by considering strength and durability criteria for cement treated bases (CTB). Microstructural characterization was aimed to explore aggregate surface roughness, mortar hardness, mineral phases, cracks, and elements within the matrix. The outcomes of optimization revealed that the optimal mixture, meeting the specifications of the Indian Road Congress, could be achieved by substituting 61% RCA and 39% FCA with 4.8% cement content. © 2024 American Society of Civil Engineers.Item Optimizing Ball Milling for High-Quality Recycled Aggregates: Examining the Mechanical Processing and Performance of Cement-Treated Bases(American Society of Civil Engineers (ASCE), 2025) Chiranjeevi, K.; Ramagiri Girish, Y.; Hemanth Kumar, D.; Mulangi, R.H.; Ravi Shankar, A.U.Producing superior-quality recycled aggregates from demolition waste is challenging. Over the years, mec hanical treatment methods for removing attached mortar from aggregates have evolved significantly. The studies on effective recycled coarse aggregate (RCA) processing with optimized processing parameters using ball milling and characterization of processed RCA (RCA) are limited. In this study, central composite design in the response surface method was employed to optimize control process factors (charge, revolution time, and aggregate weight) with aggregate properties as responses (percentage mortar removal, water absorption WA, specific gravity Sg, impact value IV, and abrasion value AV). The aggregate processed with optimized processing parameters exhibited superior quality with enhanced physical properties. The effect of the processing of RCA on the mechanical properties of cement-treated bases was studied by utilizing processed RCA in cement-treated recycled concrete aggregate mixes. The microstructural analysis was performed using 3D-surface topography, scanning electron microscopy, and energy dispersive spectroscopy. The test results demonstrated a 63% reduction in water absorption and an improvement in Sg, IV, and AV by 12.3%, 38%, and 23.7%, respectively. It is also found that the unconfined compressive strength and flexural strength with processed RCA are improved by 31.5% and 45.7%, respectively. Natural coarse aggregate can be completely replaced with processed RCA in cement-treated bases with the optimized processing method. © 2025 American Society of Civil Engineers.