Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Experimental studies on turning of discontinuously reinforced aluminium composites under dry, oil water emulsion and steam lubricated conditions using TAGUCHI's technique(Gazi University Eti Mahallesi, 2009) Shetty, R.; Pai B, R.B.; Rao, S.S.This paper reports on the experimental investigations carried out under dry, oil water emulsion and steam lubricated conditions in turning of DRACs. The measured results were then collected and analyzed with the help of the commercial software package MINITAB15. The experiments were planned on orthogonal arrays, made with prefixed cutting parameters and different lubricated conditions. An analysis of variance (ANOVA) was carried out to check tho validity of the proposed parameters and also their percentage contributions. The results of the tests show that with proper selection of the range of cutting parameters, it is possible to obtain better performance under steam lubricated condition.Item Taguchi's technique in machining of metal matrix composites(Brazilian Society of Mechanical Sciences and Engineering, 2009) Shetty, R.; Pai B, R.B.; Rao, S.S.; Nayak, R.This paper presents the study on Taguchi's optimization methodology, which is applied to optimize cutting parameters in turning of age hardened Al6061-15% vol. SiC 25 ?m particle size metal matrix composites with Cubic boron nitride inserts (CBN) KB-90 grade using steam as cutting fluid. Analysis of variance (ANOVA) is used to study the effect of process parameters on the machining process. This procedure eliminates the need for repeated experiments, time and conserves the material by the conventional procedure. The turning parameters evaluated are speed, feed, depth of cut, nozzle diameter and steam pressure. A series of experiments are conducted using PSG A141 lathe (2.2 KW) to relate the cutting parameters on surface roughness, tool wear, cutting force, feed force, and thrust force. The measured results were collected and analyzed with the help of the commercial software package MINITAB15. As well, an orthogonal array, signal-to-noise ratio is employed to analyze the influence of these parameters. The method could be useful in predicting surface roughness, tool wear, cutting force, feed force and thrust force as a function of cutting parameters. From the analysis using Taguchi's method, results indicate that among the all-significant parameters, steam pressure is the most significant parameter. © 2009 by ABCM.Item Effect of process parameters in face milling operation and analysis of cutting force using indirect method(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2018) Malghan, R.L.; Karthik, K.M.C.; Shettigar, S.; Rao, S.S.; D’Souza, R.J.Amelioration of demand for quality in machining-related products has resulted in the manufacturing industries as cornerstone for enhancement in quality control measures of the machining process. Milling, like any metal cutting operation, is used with an objective of optimizing surface roughness. Meticulous prediction of surface quality of a particular material during face milling operation is highly important for the purpose of controlling product quality and production rate. The machining characteristics of AA6061 using face milling were investigated. To calculate the cutting force through indirect approach, during machining the data acquisition was performed using a FANUC LAN cable. The data related to the current drawn by each axis were captured under two varying cases, one “With Cut” and another “Without Cut.” The experimental plan was executed by adopting the Taguchi approach to minimize experimental cost. The results attained through analysis of variance signify that the projected mathematical model can efficiently illustrate the performance in the boundary limit of the premeditated factors. © 2017 Taylor & Francis.Item Experimental assessment of FSW process to join AA6061/Rutile composite and parametric optimization using TGRA(IOP Publishing Ltd, 2021) Prabhu B, S.R.; Shettigar, A.; Herbert, M.A.; Rao, S.S.Present study is focused on investigating the effect of various friction stir welding (FSW) process variables on AA6061/Rutile composites welding quality. FSWof composites was performed considering tool geometry (Tg), welding speed (Ws) and rotational speed (Ns) as ideal parameters for multi-response optimization. Experiments were designed based on the L9 orthogonal array. Analysis of variance (ANOVA) was utilized to evaluate the effects of these welding process variables on output responses namely hardness and ultimate tensile strength (UTS). Main effects plots were drawn to found out the optimal levels of these process parameters. Multi-response optimization of the welding process has been performed using Taguchi's grey relational analysis (TGRA). Analysis revealed that welding speed of 90mmmin-1, a tool with a square pin, and rotational speed of 1000 rpm produced an FSWjoint with excellent mechanical properties. Microstructure analysis revealed that refinement in the grain structure and redistribution of reinforced particles helped in improved joint strength. © 2021 IOP Publishing Ltd.Item Optimization of FSW process parameters for maximum UTS of AA6061/rutile composites using Taguchi technique(Sharif University of Technology, 2022) Prabhu B, S.R.; Shettigar, A.; Herbert, M.A.; Rao, S.S.In the friction stir welding process, preferred joint property is vastly reliant on the selection of optimal welding conditions. The present study aims to use the Taguchi technique to find the optimal process conditions for achieving superior Ultimate Tensile Strength (UTS) in friction stir welded Aluminum Matrix Composite (AMC) joints. AMCs reinforced with rutile particles which have a potential application in the aerospace, automotive, and marine industries are used in the present work. Taguchi parametric design technique was used to identify the effect of rotational speed, tool traverse speed, and tool geometry on joint strength. Taguchi approach confined the optimum level of process variables and these variables were optimized. The investigation showed that the parameters within the selected value range will seriously affect the output. The predicted value of the output response was 155.48 MPa, which was validated by further experiments using the optimum process variables. Analysis Of Variance (ANOVA) results indicated that the UTS of the composite joint is mainly affected by the tool traverse speed followed by rotational speed, and tool geometry. The microstructural study unveiled that grain size is dependent on process variables and finer grains offer better joint properties. © 2022 Sharif University of Technology. All rights reserved.Item Optimization of process parameters for friction stir processing (FSP) of AA8090/boron carbide surface composites(Springer Science and Business Media Deutschland GmbH, 2024) Adiga, K.; Herbert, M.A.; Rao, S.S.; Shettigar, A.K.Friction Stir Processing (FSP) is an innovative and promising technique for microstructure refinement, material property enhancement, and surface composite production. The current study describes the fabrication of AA8090/boron carbide surface composites (SCs) by FSP. Experimental studies were conducted by varying the FSP parameters, specifically the rotational speed (800–1400 rpm), traverse speed (25–75 mm/min), and groove width (1–1.8 mm). Ultimate Tensile Strength (UTS), Surface Roughness (SR), and Percentage Elongation (El) were used as response measures. Experiments were planned based on the central composite design (CCD) of Response Surface Methodology (RSM) and a mathematical relationship between the input parameters and UTS, SR and El, and were obtained by RSM. The model adequacy was tested using analysis of variance (ANOVA). The models enabled the examination of individual and interaction effects of input parameters on the UTS, SR, and El of the produced SCs. AA8090/boron carbide SC strength was optimal of 366 MPa at 800 rpm, 75 mm/min, and 1.8 mm and optimal 21.13% elongation at 1400 rpm, 25 mm/min, and 1 mm. A smoother surface with 0.82-μm roughness was optimal at 1400 rpm, 25 mm/min, and 1.2 mm. The present study uses the FSP method to synthesize near-net-shaped SCs without further machining by systematically selecting process parameters. The study shows that the increase in rotational speed during AA8090/boron carbide SC fabrication produces composites with a good surface finish, lower UTS, and good ductility. However, the increase in the other two parameters, namely, traverse speed and groove width, produces low ductile composites with rougher surfaces and higher strengths. Graphical abstract: (Figure presented.) © International Institute of Welding 2024.