Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item Semi-analytical method for heat and moisture transfer in packed bed of silica gel(2011) Ramzy K, A.; Ashok Babu, T.P.; Kadoli, R.A semi-analytical model for the heat and mass transfer of adsorption and desorption processes of the vertical solid desiccant packed bed dehumidifier is presented on the basis of quasi-steady state assumption, and is solved using close form integration with the limits equivalent to bed and time increments, and numerically by Runge-Kutta Fehlberg and forward scheme finite difference techniques. The most important parameters during the dehumidifier operation, namely, (i) exit air temperature and humidity, (ii) axial temperature distribution in the bed and (iii) water content are evaluated. Stability of the semi-analytical method is investigated and found that the main parameters affecting the model stability are the bed and time increments size. A dimensionless parameter combining time and bed increments size and air velocity named velocity ratio is defined and investigated. It is found that when the velocity ratio equals the ratio of particle diameter to bed length, the method is stable, and as the velocity ratio is made smaller beyond the stable velocity ratio, the results remain unchanged. The results of semi-analytical and numerical models agree well with the experimental results for both desorption and adsorption processes. Using the proposed semi-analytical model, the minimum and maximum relative errors for exit air temperature are 2.24% and 11.78%, respectively and for exit air humidity the minimum and maximum errors are 3.79% and 27.17% respectively. © 2010 Published by Elsevier Ltd. All rights reserved.Item Improved utilization of desiccant material in packed bed dehumidifier using composite particles(2011) Ramzy K, A.; Kadoli, R.; Ashok Babu, T.P.Solid desiccant dehumidifiers are widely used in drying processes. In most of these dehumidifiers, the desiccant material is used as packed bed of granule or spherical particles. Investigations of intra-particle heat and mass transfer processes has shown that the entire portion of the particle is not participating effectively during adsorption as well as desorption processes [Pesaran AA, Mills F. Moisture transport in silica gel packed beds-I. Theoretical study. International Journal of Heat and Mass Transfer 1987; 30: 1037-49]. This is because the diffusion rate is very small compared to that of convection. In the present work, a new desiccant composite particle, in which the unutilized portion of the spherical desiccant particle is replaced with an inert particle, is proposed. By replacing the conventional particles with composite particles for the same mass of desiccant material, the available area for heat and mass transfer increases and more amount of desiccant material is effectively utilized. Further, in order to ascertain the improvement in the performance of the desiccant bed using the composite particles, various factors like thermo-physical properties of the inert material, composite particle thickness ratio, bed configuration, bed volume, the pressure drop and the increase in total adsorbed or desorbed mass have to be considered. In view of this, a theoretical investigation of the operation of vertical solid desiccant packed bed dehumidifier, using both conventional silica gel particles as well as the new proposed composite silica gel particles has been reported. A modified solid side resistance (MSSR) model is developed for the prediction of intra-particle temperature and water content profiles. Results of the present theoretical models, when applied to packed bed of conventional silica gel particles, agree well with the experimental results from the literature for both desorption and adsorption processes. From the theoretical results, more utilization for the desiccant material is obtained when ordinary silica gel particles are replaced by composite silica gel particles. For the same amount of desiccant material and same mass flow rate of air, using particles of 0.2 thickness ratio the pressure drop decreases by about 60% for the case investigated. In addition, an increase of about 11.07% and 20.46% in total mass adsorbed and desorbed respectively are obtained. At the time when adsorption process ends, an increase of 15.5% in the bed effectiveness has been obtained. In addition, the expected improvement in total mass adsorbed and desorbed is observed to be dependent on the inert material thermo-physical properties for thickness ratio less than 0.5. An optimization technique relating the composite particle design, resulting savings in pressure drop and bed volume increase is proposed. © 2010 Elsevier Ltd.Item Performance studies on the desiccant packed bed with varying particle size distribution along the bed(2012) Ramzy K, A.; Kadoli, R.; Ashok Babu, T.P.The transient heat and mass transfer in a desiccant packed bed containing varying particle diameter distribution along the axial direction has been investigated using the pseudo gas controlled approach that considers the heat conduction in the bed. The numerical results of the present model and the experimental data from literature show good agreement with a maximum root of mean square of errors of 3% and 2% for exit air temperature and humidity ratio, respectively. The improvement in the total mass adsorbed and/or reduction in pressure drop has been investigated for various cases of packed bed namely, uniform particle diameter, linear, parabolic and cubic ascending and descending distributions. It has been found that there is a 25.7% reduction in pressure drop with negligible reduction in the total mass adsorbed for a desiccant bed with cubic type particle size distribution when compared to the bed with uniform particle diameter of 1.0 mm. A threshold flow velocity exists below which the total mass adsorbed is independent of particle diameter distribution type. © 2012 Elsevier Ltd and IIR. All rights reserved.