Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
14 results
Search Results
Item Effect of Rolling Reduction on Microstructure and Mechanical Properties Cu-3%Ti Alloy(Pleiades journals, 2019) Singh, P.; Ramesh, S.; Anne, G.; Shivananda Nayaka, H.Cu-3%Ti alloy is cold rolled with different reduction ratios and the microstructures and mechanical properties are compared with that of as-cast Cu-3%Ti alloy. Microstructure was analyzed using optical microscope and scanning electron microscope. Optical microscopy revealed significant grain refinement that occurred during the rolling process. Tensile test results indicate that the UTS is increased by a significant amount up to 80% rolling reduction. A significant amount of tensile strength increased up to 812 MPa is about 1.69 times that of the cast Cu-3%Ti alloy. Hardness of the rolled Cu-3%Ti increased as % reduction increased. Dimples were revealed on the fracture surface of the rolled Cu-3%Ti specimens indicating a ductile nature of the fracture. © 2019, Springer Nature Singapore Pte Ltd.Item Influence of Multi Axial Forging (MAF) on Microstructure and Mechanical Properties of Cu-Ti Alloy(Elsevier Ltd, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Gopi, K.R.Multi axial forging (MAF) is one among the severe plastic deformation (SPD) processes, where large strains are imposed into the component. In the present work, as-received Cu-1.5%Ti alloy was subjected to MAF for 2 and 4 cycles at room temperature. Microstructure showed grain refinement after 2 and 4 cycles. Average grain size obtained for MAF processed samples after 2 and 4 cycles are 120 μm and 40 μm, respectively compared to initial grain size of 800 μm. The Mechanical properties were analyzed for as-received and MAF processed samples. Tensile test showed increased ultimate tensile strength (493 MPa) for MAF 4-cycle sample compared to as-received (191 MPa) condition with accumulated strain of 2.18 for 4 cycles. Increase in hardness was observed for MAF processed sample of 143 Hv for 4-cycle compared to as-received sample of 67 Hv. © 2018 Elsevier Ltd.Item Influence of cold rolling process on microstructure and mechanical properties of Cu-1.5%Ti alloy(American Institute of Physics Inc. subs@aip.org, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Anne, G.; Gopi, K.R.The effects of cold rolling on the microstructure evolution and mechanical properties of Cu-1.5%Ti alloy were investigated. The results showed that the tensile strength of the Cu-1.5%Ti alloy increased with an increase of rolling deformation at room temperature. Significant grain refinement took place during rolling process revealed in optical microstructure and transmission electron microscope analysis. XRD patterns revealed peaks indexed to Cu, Cu3-Ti2 and Cu4-Ti3 after 8-pass rolling process. Microhardness of the rolled Cu-1.5%Ti alloy layers increased incessantly with increase in the number of rolling passes. Tensile strength increased up to 294 MPa which was about 1.54 times higher than that of the cast Cu-1.5%Ti alloy. Fracture surfaces of the rolled Cu-1.5%Ti alloy revealed the dimples in the structure, which is an indication of ductile fracture. © 2018 Author(s).Item Investigation of microstructure and mechanical properties of the Cu-3% Ti alloy processed by multiaxial cryo-forging(Cambridge University Press, 2018) Ramesh, S.; Shivananda Nayaka, H.; Gopi, K.R.; Sahu, S.; Kuruveri, U.B.A Cu-3%Ti (wt%) alloy was processed by multiaxial forging (MAF) at cryogenic temperature up to 3 cycles, imposing a total strain of 1.6. Microstructure and mechanical properties of the unprocessed and cryo-forged samples were analyzed. X-ray diffraction results showed deviation in peak broadening and peak intensity of the cryo-forged samples in comparison to that of unprocessed, which are due to texture modification caused by grain refinement during the MAF process. Microstructural analysis showed reduction in grain size from 80 m in the as-received condition to 250 nm after 3 cycles. Electron backscatter diffraction results indicated the transformation of high angle grain boundaries to low angle grain boundaries in all 3 cycles when compared to the as-received condition. Reduction in ductility was observed after 1 cycle, but with an increase in the number of cycles, both strength and ductility increased. After 3 cycles, ultimate tensile strength and hardness reached 1126 MPa and 427 Hv as compared to 528 MPa and 224 Hv for the as-received condition. Fractography analysis showed decrement in dimple size after 1 cycle, in comparison to that of the as-received condition. However, it kept on increasing for higher number of cycles. © © Materials Research Society 2018.Item Effects of combined multiaxial forging and rolling process on microstructure, mechanical properties and corrosion behavior of a Cu-Ti alloys(Institute of Physics Publishing helen.craven@iop.org, 2019) Ramesh, S.; Anne, G.; Shivananda Nayaka, H.; Sahu, S.; Arya, S.Combined multiaxial forging (MAF) and rolling was performed on Cu-3% Ti (wt%) alloy at room temperature with emphasis on microstructural evolution, improvement in mechanical properties, and corrosion resistance. Microstructural changes were confirmed from various characterization techniques, and co-related with mechanical properties. TEM analysis revealed high shear band density in the 3 pass MAF + 90% rolled sample appearing due to high strain. EBSD analysis revealed transformation to low angle grain boundaries from high angle grain boundaries. Maximum microhardness and UTS reached to 340 HV and 960 MPa, respectively in the processed samples. Significant grain refinement was observed in MAF processed Cu-3%Ti alloy, and after combined MAF + rolling, higher dislocation density and refinement of shear bands were observed. In addition, potentio-dynamic polarization test was used to study the corrosion behavior of the alloy. Scanning electron microscope (SEM) was used to analyze the corroded surface morphology. © 2019 IOP Publishing Ltd.Item Effect of multiaxial cryoforging on microstructure and mechanical properties of a Cu-Ti Alloy(Institute of Physics Publishing helen.craven@iop.org, 2019) Ramesh, S.; Shivananda Nayaka, H.S.; Gopi, K.R.; Sahu, S.Cu-Ti alloy, processed by multiaxial forging (MAF) at cryogenic temperature with a cumulative strain up to 1.64, was investigated for microstructure and mechanical properties. The deformed microstructures were analyzed using optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The average grain size of 2 ?m was achieved in the deformed sample after 3 cycles of MAF. TEM studies indicated that the shear bands width of the deformed sample after 3 cycles reduced to 1 ?m. Tests for mechanical properties indicated an increase in tensile strength and hardness and it was found to be correlated with an increase in dislocation density and grain boundary strengthening mechanism. Ultimate tensile strength (UTS) of 390 MPa, 480 MPa, and 590 MPa was observed in MAF processed samples after 1, 2, and 3 cycles, respectively. Hardness increased from 65 Hv (as-received) to 240 Hv after 3 cycles of MAF. Fractography analysis showed that, with an increase in number of MAF cycles, dimple size reduced up to 1 cycle and percentage elongation increased after 2 cycles of MAF. © 2018 IOP Publishing Ltd.Item Influence of Multidirectional Forging on Microstructural, Mechanical, and Corrosion Behavior of Mg-Zn Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2019) Ramesh, S.; Anne, G.; Shivananda Nayaka, H.S.; Sahu, S.; Ramesh, M.R.Multidirectional forging (MDF) was applied to Mg-6%Zn alloy up to 5 passes successfully at 280 °C. MDF-processed materials were characterized using optical microscope, scanning electron microscope, electron backscatter diffraction, transmission electron microscope, and x-ray diffraction. Obtained results showed a significant reduction in grain size (up to 3.8 ?m) having a large fraction of high-angle grain boundaries after 5 passes of MDF process. Maximum tensile strength of 230 MPa was achieved for 5-pass MDF-processed Mg-6%Zn alloy which is about ~ 2.0 times higher in comparison with that of homogenized alloy (117 MPa) and was attributed to higher dislocations density and grain refinement. Corrosion behavior of the alloy was investigated in 0.1 M NaCl solution using potentiodynamic polarization test, electrochemical impedance spectra analysis, and immersion tests. It was found that the corrosion rate of 5-pass MDF sample improved (0.34 mm/year) ~2.5 times in comparison with that of homogenized Mg-6%Zn alloy (0.86 mm/year) due to fine grain structure, which creates more grain boundaries that act as a corrosion barrier. © 2019, ASM International.Item Investigation of Tribological and Corrosion Behavior of Cu-Ti Alloy Processed by Multiaxial Cryoforging(Springer, 2020) Ramesh, S.; Shivananda Nayaka, H.Wear and corrosion properties of Cu-3%Ti alloy subjected to multiaxial forging (MAF) under cryogenic conditions are estimated at room temperature. Wear study was performed using pin-on-disk dry sliding wear setup at 10 and 20 N loads with varying sliding distances (500-3000 m) under different sliding velocities (1 and 2 m/s). Coefficient of friction and wear mass loss decreases with an increase in MAF cycles, due to increases in hardness of samples. Wear resistance decreases with an increase in load and sliding velocity. Worn surface shows the plastic deformation regions, wear track, micro-cracks, micro-plowing groove and scratches. Potentiodynamic polarization test clearly shows that current density (Icorr) increases with an increase in MAF passes, because of grain refinement. Reduction in corrosion rate was evident from electrochemical impedance spectroscopy results which show increased diameter of the capacitive arc. An enhancement of corrosion resistance was revealed at higher MAF passes. © 2020, ASM International.Item Influence of Ball Burnishing Process on Equal Channel Angular Pressed Mg-Zn-Si Alloy on the Evolution of Microstructure and Corrosion Properties(Springer Science and Business Media B.V., 2021) Ramesh, S.; Anne, G.; Kumar, G.; Jagadeesh, C.; Shivananda Nayaka, H.In the present study, Mg-4Zn-1Si alloy was subjected to equal channel angular pressing (ECAP) up to 4 passes at 300 °C, followed by ball burnishing using 0.3 mm depth of press, 300 mm/min feed and 1 pass successfully. The effect of ECAP and ECAP + ball burnishing process on microstructure, mechanical properties (tensile and hardness) and corrosion behavior was systematically investigated. After 4 pass ECAP, initial coarse grains (210 ?m) were refined and average grain size is 6 ?m and after ball burnishing, the grain size is found to be 3.3 ?m. Microstructure evolution is discussed using optical images, scanning electron microscope images and transmission electron microscope images. For ECAP samples, maximum strength and hardness was recorded at 3 pass. Both strength and hardness decreased for 4 pass ECAP processed samples, even though grain size decreased, this is because of texture modification in the material. ECAP 4 pass + ball burnished samples exhibited 48.5% enhancement of microhardness as compared to 4 pass ECAP samples. Corrosion resistance of the samples decreased with increase in the number of ECAP passes, this is due to strain-induced grain refinement with more crystalline defects in samples. Combined process of ECAP and ball burnishing effectively reduces the Icorr and this consequently reduces corrosion rate of the Mg–4Zn-1Si alloy. © 2020, Springer Nature B.V.Item Effect of Equal Channel Angular Pressing on Properties Evaluation of Biodegradable Mg-Zn-Mn Alloy(Springer Science and Business Media Deutschland GmbH, 2021) Ramesh, S.; Kumar, G.; Jagadeesh, C.; Anne, G.; Shivananda Nayaka, H.Equal channel angular pressing (ECAP) was used to process Mg-4Zn-1Mn alloy at 300 °C using route Bc up to 4 pass with a cumulative strain of 3.2. Optical microscope (OM), microstructures results shows homogenized sample grain size was 260 µm, after 4 pass ECAP grain size was decreased to 6 µm. Electron back-scattered diffraction (EBSD) shows the misorientation angle converted from low-angle grain boundaries (LAGB) to high-angle grain boundaries (HAGB). Dislocation density and fine grains were observed from transmission electron microscope (TEM) images. Strength has been increased from 156 to 218 MPa and hardness increased to 68 Hv after 4 pass of ECAP. Fractography analysis revealed that dimple size decreases as ECAP passes increased. XRD analysis shows the peak broadening and intensity variation, because of grain refinement. The corrosion behavior of the homogenized and ECAP-processed samples were investigated by electrochemical tests using simulated body fluids (SBF) at 37 ± 1 °C. The lower corrosion resistance of ECAP-processed Mg-4Zn-1Mn alloy attributed to the strain-induced crystalline defects, subgrain boundaries and high-density dislocations. Enhanced strength and ductility combined with lower corrosion resistance of ECAP-processed Mg-4Zn-1Mn has greater potentials for biomedical implants. © 2021, The Author(s), under exclusive licence to Springer Nature Switzerland AG.