Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Ramesh, M.R.Subject: search.filters.subject.Surface roughness

Search Results

Now showing 1 - 10 of 23
  • No Thumbnail Available
    Item
    Effect of machining process parameters on productivity rate and surface roughness of machined TiNiCo alloy
    (Elsevier Ltd, 2018) Soni, H.; Narendranath, S.; Ramesh, M.R.
    TiNiCo based shape memory alloy is an important alloy for biomedical applications such as bone staple due to their excellent biocompatibility, corrosion resistance, shape memory effect (SME) and pseudoelasticity (PE). Traditional machining of such kind of alloys is difficult due to their outstanding properties. Wire electro discharge machining (WEDM) is most suitable non-traditional machining process for machining of these alloys. Present study focuses on effect of WEDM process parameters on productivity rate and surface roughness. Pulse on time, servo voltage and wire speed were considered as WEDM process parameters with their five levels in the current study. Our observation exhibit that productivity rate and surface roughness increases with increasing pulse on time and both outputs decrease with increasing servo voltage while wire speed does not show much effect on productivity rate as well as surface roughness. © 2018 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    Item
    An experimental study of influence of wire electro discharge machining parameters on surface integrity of TiNiCo shape memory alloy
    (Cambridge University Press, 2017) Soni, H.; SannaYellappa, N.; Ramesh, M.R.
    Shape memory alloys (SMAs) are unique class of smart materials with excellent physical, mechanical and biomedical properties, which have wide applications in several fields such as aerospace, robotics, biomedical, and dental etc. These alloys are well known for exhibiting shape memory effect (SME) and pseudoelasticity (PE), it is a well-established fact that they are required to be processed into functioning parts. The conventional machining affects the internal properties of shape memory alloys and hence, it is reported that nonconventional machining techniques are more suitable. Wire electro discharge machining (WEDM) is one of the nonconventional machining processes for machining complicated shapes without hampering the internal properties of such type of materials. In the present experimental investigation, wire electro discharge machining of Ti50Ni40Co10 shape memory alloy (SMA) has been carried out and machining performances such as surface roughness (SR), and material removal rate (MRR) have been evaluated. Experimental results exposed that pulse on time, pulse off time and servo voltages are most influential process parameters on the responses. The machined surface has been characterised with respect to microstructure, microhardness, and phases formed. © Materials Research Society 2017.
  • No Thumbnail Available
    Item
    ANN and RSM modeling methods for predicting material removal rate and surface roughness during WEDM of Ti50Ni40Co10 shape memory alloy
    (AMSE Press 16 Avenue Grauge Blanche Tassin-la-Demi-Lune 69160, 2017) Soni, H.; Narendranath, S.; Ramesh, M.R.
    Present study exhibits the comparison between experimental and predicted values. Where response surface method (RSM) and artificial neural network (ANN) were used as predictor for the prediction of wire electro discharge machining (WEDM) responses such as the material removal rate (MRR) and surface roughness (SR) during the machining of Ti50Ni40Co10 shape memory alloy. It has been noticed from the literature survey that pulse on time and servo voltage are most important process parameters for the machining of TiNiCo shape memory alloy, hence there are five levels of these process parameters were chosen for the present study. For the present study selected alloy has been developed through vacuum arc melting and L-25 orthogonal array has been created by using Taguchi design of experiment (DOE) for experimental plan. During the present study ANN predicted values have been found to very close to experimental values compare to RSM predicted values, hence it can be say that ANN predictor gives more accurate values compare to RSM predicted values. © 2017 AMSE Press. All rights reserved.
  • No Thumbnail Available
    Item
    Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating
    (Institute of Physics Publishing helen.craven@iop.org, 2018) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.
    CoMoCrSi superalloy powder (Tribaloy-T400) consists of intermetallic laves phase and primary eutectic phase of Co-rich solid solution. Processing of Tribaloy-T400 powder is carried out through high-energy ball milling (HEBM) technique to obtain a higher volume fraction of intermetallic laves phases. The feedstock is sprayed using high-velocity-oxy-fuel (HVOF) process on titanium grade-15 substrate. The coating microstructure is homogenized by microwave hybrid heating technique. Characterization of feedstock, as-sprayed and microwave fused coatings is done by using Scanning Electron Microscopy (SEM), Energy dispersive spectroscopy (EDS) and x-ray Diffraction (XRD). Porosity, surface roughness, microhardness, and bond strength are measured. Adhesive wear behavior of the coatings under the dry sliding condition is evaluated at an applied load of l0 and 20 N and temperature of 200, 400 and 600 °C Fused coating exhibit higher wear resistance than the as-sprayed coatings and substrate. The hard intermetallic laves phases which are amorphous (bulk metallic glass) in nature strengthen the coating at high temperatures. © 2018 IOP Publishing Ltd.
  • No Thumbnail Available
    Item
    Experimental Investigation on Effects of Wire Electro Discharge Machining of Ti50Ni45Co5 Shape Memory Alloys
    (Springer Netherlands rbk@louisiana.edu, 2018) Soni, H.; Narendranath, S.; Ramesh, M.R.
    TiNiCo shape memory alloy is most popular shape memory alloy for biomedical applications due to their outstanding properties such as shape memory effect, pseudoelasticity and transformation temperature. Machining of such kind of alloys is very difficult through conventional machining process is very difficult because they may affect their internal properties of these alloys. However conventional machining processes give poor surface quality during the machining hence non-conventional machining processes such as (wire electro discharge machining, water jet machining and electro discharge machining etc.) are more suitable for machining of such kind of alloy. From the literature it has been found that Wire electro discharge machining (WEDM) is more suitable non-conventional machining process for such kind of alloy. Present study exhibits the effects WEDM characteristics of Ti50Ni45Co5 shape memory alloy. L-9 orthogonal array has been created by using Taguchi as a design method for machining of selected alloy and machined surface characterization has been carried out at the optimized process parameters with respect to microstructures, surface topography, microhardness, XRD analysis and residual stresses. To find the optimum setting of the input process parameters a couple of optimization techniques are used, namely principal component analysis (PCA) and Gray relational analysis (GRA) technique. 125?s pulse on time (Ton), 35?s pulse off time (Toff) and 40V servo voltage (SV) were found as an optimal setting for the higher material removal rate (MRR) with better surface roughness (SR) in the present study. Moreover, characterization of the machined surface is performed with respect to microstructures, surface topography, microhardness analysis, XRD and residual stresses. Harder surface observed near the cutting edge and TiNio3 Tio2 and CuZn were noticed on the surface of machined component through XRD analysis. However, compressive residual stress has been noticed on the machined surface during WEDM process. © 2018, Springer Science+Business Media B.V., part of Springer Nature.
  • No Thumbnail Available
    Item
    Laser surface modification of Mg-Zn-Gd alloy: Microstructural, wettability and in vitro degradation aspects
    (Institute of Physics Publishing helen.craven@iop.org, 2018) Rakesh, K.R.; Bontha, S.; Ramesh, M.R.; Arya, S.; Das, M.; Balla, V.K.; Srinivasan, A.
    Mg-Zn-Gd have great potential for biomedical applications owing to excellent bioactivity and non-toxicity properties. In the present study, laser surface melting (LSM) was carried out on newly developed Mg-1Zn -2Gd (wt%) alloy. Effects of laser energy on microstructural evolution, corrosion properties, surface energy, and hardness have been investigated. The surface modified sample processed at different energy densities showed fine grain structure in the melt zone compared to the untreated substrate. Grain refinement in the laser melted region improved the hardness by 60%. The surface roughness was found to be increased with increasing laser energy density. At higher energy density, removal of materials from the surface is enhanced, resulting in deeper grooves and higher surface roughness. The wettability studies indicated that the variations in surface geometry, grain size and surface roughness of LSM samples strongly influence the surface energy and hydrophilicity. Improved wetting of LSM sample was achieved owing to grain refinement and low surface roughness. The corrosion resistance determined by immersion and electrochemical methods of laser melted sample in Hank's balanced salt solution improved considerably due to grain refinement, meltpool depth and uniform distribution of secondary phases. © 2018 IOP Publishing Ltd.
  • No Thumbnail Available
    Item
    Experimental investigation and optimization of machining parameters for sustainable machining
    (Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2018) Varghese, V.; Ramesh, M.R.; Dupadu, D.
    A detailed investigation on the effects of cutting parameters and different cooling environments on machinability of austenitic stainless steel AISI 304 is presented in this study. The need for sustainable manufacturing and better surface quality urged to explore the merits of cryogenic cooling over the other conventional cooling techniques. The end milling experiments were designed based on three parameter and three-level design considering dry, wet, and cryogenic machining environments to have a comparative study. The machinability studies such as surface roughness, tool wear, cutting forces, chip morphology, and chip reduction coefficient were investigated and compared with different machining environments. The machining parameters were optimized using Taguchi-based grey relational analysis. The cryogenic machining had the most influence on milling of AISI 304 steel and resulted in the reduction of cutting forces, surface roughness, and chip reduction coefficient in comparison with the conventional wet and dry machining. © 2018, © 2018 Taylor & Francis.
  • No Thumbnail Available
    Item
    Effect of cutting parameters on tool wear, cutting force and surface roughness in machining of MDN431 alloy using Al and Fe coated tools
    (Institute of Physics Publishing helen.craven@iop.org, 2019) V Badiger, P.V.; Desai, V.; Ramesh, M.R.; Prajwala, B.K.; Raveendra, K.
    Thin solid films are used in cutting tools in order to improve its performance, reduce tool wear and improve tool life. Cathodic arc evaporation is the state of art PVD technique widely accepted in industries for the development of thin solid films. The turning cutting tool inserts are coated with AlCN/AlC and FeCrN monolayer thin solid films using cathodic arc evaporation technique. Quality characteristics of thin films are estimated using Calo and VDI3198 tests. Thickness of the coatings are found to be 1.430 and 1.475 ?m for AlCN/AlC and FeCrN coatings respectively and adhesion quality of HF1 is attained. Performance of the thin solid films are evaluated in machining MDN431 steel with range of cutting speed (59-118 m min-1), feed rate (0.062-0.125 mm/rev) and depth of cut (0.2-0.4 mm). Experiments are performed based on full factorial design and regression analysis. Optimization of the process parameters is carried out using combined techniques of desirability and Particle swarm optimisation (PSO). The objective of the study is to establish correlation between machining parameters with cutting force, tool wear and surface roughness. Optimal process parameter for least cutting force and surface roughness are obtained for coatings. ANN has been adopted to improve the coefficient of determination (CoD) and capability of predictive regression models. ANN trained model and mathematical regression models are adequate to predicted the responses, which follows the experimental data with minimum absolute error. The AlCN/AlC coatings exhibited lower cutting forces and surface roughness than FeCrN coated tools. Tool wear was reduced by 3.62 times in AlCN/AlC and 1.63 times in FeCrN coated tools compared to uncoated tool which is due to increased hardness and elastic modulus of the coating. © 2018 IOP Publishing Ltd.
  • No Thumbnail Available
    Item
    Influence of deep cryogenic treatment on performance of cemented carbide (WC-Co) inserts during dry end milling of maraging steel
    (Elsevier Ltd, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.
    Cryogenic treatment has developed as a technique to improve the life of the cutting tool, especially tungsten carbide inserts. The present study investigates the effect of cryogenic treatment of cemented carbide (WC-Co) inserts at the different soaking period of 18 h (CT-18), 24 h (CT-24) and 32 h (CT-32) at a sub-zero temperature of ?196 °C. The soaking period plays a crucial role in improving the wear resistance of the cryogenically treated tools. It is vital to determine the critical soaking period for the cryogenic treatment of cemented carbides. The mechanical and metallurgical characterization of cryogenically treated cemented carbide insert is carried out to understand the changes in the microstructure, grain size, chemical composition, microhardness and electrical conductivity after cryogenic treatment. The end milling experiments on maraging steel under dry environment are carried out using cryogenically treated inserts at different holding time and untreated inserts (UT). The machining performance of treated and untreated inserts are compared with respect to tool wear, surface roughness and cutting forces. The results revealed that cryogenic treatment is effective in resisting tool wear even at high spindle speeds. The cryogenically treated inserts exhibited higher tool life, better surface finish and lower cutting forces during machining at different spindle speeds. The optimum soaking time for cryogenic treatment of WC-Co inserts is found to be 24 h (CT-24) beyond which there is no improvement in microhardness and wear resistance. © 2018
  • No Thumbnail Available
    Item
    Characterisation and performance evaluation of TiSiN &tiAlSiN coatings by RF magnetron sputtering deposition during end milling of maraging steel
    (Institute of Physics Publishing helen.craven@iop.org, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.; Shaik, H.
    Monolayer nanostructured thin films of TiSiN & TiAlSiN were deposited on WC-Co milling inserts using RF magnetron sputtering for metal cutting. The alloy targets of TiSi (80/20 at%) & TiAlSi (34/56/10 at%) were used for the deposition in an Ar + N atmosphere. The deposition time and parameters are optimized to develop a uniform and homogenous coating. The mechanical and metallurgical properties are characterized to analyze the wear resistance of the coating. The machinability studies on MDN 250 maraging steel is carried out using TiSiN and TiAlSiN coated WC-Co inserts under dry and wet environment. The machining responses such as surface roughness, cutting force, tool wear and tool life are analyzed by varying spindle speed. The results showed that TiAlSiN coating had a higher wear resistance and machining performance compared to the TiSiN coating owing to the high hardness and plasticity index of the coating. © 2020 IOP Publishing Ltd.