Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
40 results
Search Results
Item Combating corrosion degradation of turbine materials using HVOF sprayed 25% (Cr3C2-25(Ni20Cr)) + NiCrAlY coating(2013) Jegadeeswaran, N.; Ramesh, M.R.; Bhat, K.High velocity oxy fuel process (HVOF) is an advanced coating process for thermal spraying of coatings on to components used in turbines. HVOF process is a thermal spray coating method and is widely used to apply wear, erosion, and corrosion protective coatings to the components used in industrial turbines. 25% (Cr3C2-25(Ni20Cr)) + NiCrAlY based coatings have been sprayed on to three turbine materials, namely, Ti-31, Superco-605, and MDN-121. Coated and uncoated substrates were subjected to hot corrosion study under cyclic conditions. Each cycle consisted of 1 hour heating at 800°C followed by 20 minutes air cooling. Gravimetric measurements were done after each cycle and a plot of weight gain as a function of number of cycles is drawn. Parabolic rate constants were estimated for the understanding of corrosion behaviour. It was observed that coated Ti-31 and MDN-121 were more resistant compared to the uncoated ones. Uncoated superco-605 was undergoing sputtering during corrosion study and hence comparison between coated and uncoated superco-605 was difficult. The cross-sectional analysis of the corroded, coated samples indicated the presence of a thin layer of chromium oxide scale on the top of the coating and it imparted better corrosion resistance. Parabolic rate constants also indicated that coating is more beneficial to Ti-31 than to MDN-121. © 2013 N. Jegadeeswaran et al.Item High temperature corrosion behaviour of HVOF sprayed WC-CrC-Ni coatings(Inderscience Publishers, 2016) Somasundaram, B.; Kadoli, R.; Ramesh, M.R.; RAMESH, C.S.The present work aims to study the hot corrosion resistance of high velocity oxy-fuel (HVOF) sprayed WC-CrC-Ni coating developed on three types of boiler tube materials such as SA213-T22, MDN-310 and Superfer 800 H steels. Hot corrosion studies were conducted in a molten salt environment of Na2SO4-60%V2O5 at 700°C and thermogravimetric analysis was used to establish kinetics of corrosion. Corrosion kinetics of coated steels followed nearly parabolic behaviour and showed a lower corrosion rate in comparison to uncoated alloys. It is concluded that corrosion is restricted to the external surface of the coating and the formation of thick scale composed of oxides of Cr, Ni and their spinel oxides, acts as a diffusion barrier to the transportation of corrosive species into the coating. The carbides of tungsten and chromium uphold the strength of the coating. © © 2016 Inderscience Enterprises Ltd.Item Elevated Temperature Solid Particle Erosion Performance of Plasma-Sprayed Co-based Composite Coatings with Additions of Al2O3 and CeO2(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Nithin, H.S.; Desai, V.; Ramesh, M.R.In this paper, investigation into solid particle erosion behavior of atmospheric plasma-sprayed composite coating of CoCrAlY reinforced with Al2O3 and CeO2 oxides on Superni 76 at elevated temperature of 600 °C is presented. Alumina particles are used as erodent at two impact angles of 30° and 90°. The microstructure, porosity, hardness, toughness and adhesion properties of the as-sprayed coatings are studied. The effects of temperature and phase transformation in the coatings during erosion process are analyzed using XRD and EDS techniques. Optical profilometer is used for accurate elucidation of erosion volume loss. CoCrAlY/CeO2 coating showed better erosion resistance with a volume loss of about 50% of what was observed in case of CoCrAlY/Al2O3/YSZ coating. Lower erosion loss is observed at 90° as compared to 30° impact angle. The erosion mechanism evaluated using SEM micrograph revealed that the coatings experienced ductile fracture exhibiting severe deformation with unusual oxide cracks. Reinforced metal oxides provide shielding effect for erodent impact, enabling better erosion resistance. The oxidation of the coating due to high-temperature exposure reforms erosion process into oxidation-modified erosion process. © 2017, ASM International.Item HVOF sprayed Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings: Microstructure, microhardness and oxidation behaviour(Elsevier Ltd, 2018) Reddy, N.C.; Kumar, B.S.A.; Reddappa, H.N.; Ramesh, M.R.; Koppad, P.G.; Kord, S.This paper reports the development of Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings on AISI 420 stainless steel (MDN-420) and titanium alloy ASTM B265 (Ti-15) by HVOF technique. Microstructure, microhardness and high temperature oxidation behaviour of coatings were investigated. Microstructure of coatings was dense and displayed layers depicting lamellar structure. The microhardness of coatings was significantly higher than that of substrate owing to higher density and cohesive strength between individual splats of coating materials. Cyclic oxidation studies conducted on Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings showed oxide scale was composed of various oxides like NiO, NiCr2O4 and Cr2O3 phases. The formation of compact and protective NiO phase in case of Ni3Ti coatings; NiO and Cr2O3 phases in Ni3Ti+(Cr3C2+20NiCr) coatings stabilised the weight gain exhibited slow oxidation rate at higher temperatures. © 2017 Elsevier B.V.Item Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating(Institute of Physics Publishing helen.craven@iop.org, 2018) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi superalloy powder (Tribaloy-T400) consists of intermetallic laves phase and primary eutectic phase of Co-rich solid solution. Processing of Tribaloy-T400 powder is carried out through high-energy ball milling (HEBM) technique to obtain a higher volume fraction of intermetallic laves phases. The feedstock is sprayed using high-velocity-oxy-fuel (HVOF) process on titanium grade-15 substrate. The coating microstructure is homogenized by microwave hybrid heating technique. Characterization of feedstock, as-sprayed and microwave fused coatings is done by using Scanning Electron Microscopy (SEM), Energy dispersive spectroscopy (EDS) and x-ray Diffraction (XRD). Porosity, surface roughness, microhardness, and bond strength are measured. Adhesive wear behavior of the coatings under the dry sliding condition is evaluated at an applied load of l0 and 20 N and temperature of 200, 400 and 600 °C Fused coating exhibit higher wear resistance than the as-sprayed coatings and substrate. The hard intermetallic laves phases which are amorphous (bulk metallic glass) in nature strengthen the coating at high temperatures. © 2018 IOP Publishing Ltd.Item Microstructure and tribological behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere/solid lubricants composite coatings(Elsevier B.V., 2018) Doddamani, M.; Mathapati, M.; Ramesh, M.R.Present investigation deal with NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2, NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 and NiCrAlY/WC-Co/Cenosphere coatings deposited on MDN 321 steel using atmospheric plasma spraying. Tribological properties of MDN 321 steel and coatings are evaluated from room temperature (RT) to 600 °C under dry lubrication conditions using a pin on disc high-temperature tribometer. Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Energy Dispersive Spectroscopy (EDS) are used to characterize the coatings. Presence of cenospheres in these coatings might effectively reduce wear acting as localized regions accumulating wear debris. The result shows that wear rate of all the coatings are lower as compared to MDN 321 substrate at all the test conditions. NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS/CaSO4 coatings registered lower friction coefficient as compared to NiCrAlY/WC-Co/Cenosphere coating and MDN 321 substrate. Characterization of the NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 coatings worn out surface suggests that MoS2 provides lubrication at 200 °C and formation of CaMoO4, MoO3 through tribo chemistry reaction at higher temperature provides lubrication at 600 °C. SEM micrograph of worn surface demonstrates that the main wear mechanism is plowing and delamination. © 2018 Elsevier B.V.Item Microstructure and tribological characteristics of APS sprayed NiCrBSi/flyash cenosphere/Cr2O3 and NiCrBSi/flyash cenosphere/Mo composite coatings at elevated temperatures(Institute of Physics Publishing helen.craven@iop.org, 2019) Nagabhushana, N.; Rajanna, S.; Mathapati, M.; Ramesh, M.R.; Koppad, P.G.; Reddy, N.C.In the present investigation NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo composite coatings are developed using atmospheric plasma spray technique on superni 76 alloy. Coatings are characterized in terms of microstructure, phase analysis, and microhardness. Tribological properties of the coatings are evaluated using a pin on disc tribometer. Test is conducted under dry sliding conditions at room temperature, 200 °C, 400 °C, and 600 °C respectively. Microstructure and worn surfaces of the coatings are analyzed by utilizing Scanning Electron Microscope (SEM) where in phase analysis is carried out using x-ray diffractometer (XRD). XRD results revealed the presence of ?-Ni as primary phase along with Ni3B, Cr7C3, SiO2 and Al2O3 as minor phases in both the NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo coatings. Among the two coatings, Mo composite coating exhibited lower porosity and higher microhardness. The friction coefficient of both the coatings decreased with increasing temperature. The wear rate is found to decrease at lower temperatures but increased at a higher temperature (>400 °C) for Cr2O3 composite coating wherein Friction coefficient is decreased with increase in the temperature for Mo composite coatings. The worn surface analysis conducted revealed abrasive wear at lower temperatures while the transition from abrasive to adhesive is observed at higher temperatures. © 2019 IOP Publishing Ltd.Item Microstructure and tribological behavior of flame sprayed and microwave fused CoMoCrSi/CoMoCrSi-Cr3C2 coatings(Institute of Physics Publishing helen.craven@iop.org, 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This present work deals with the investigation of dry sliding wear behavior of CoMoCrSi and CoMoCrSi-Cr3C2 depositing on titanium substrate through Flame spray process, subsequently fused by the microwave hybrid heating process. Prior to the deposition of the coating, CoMoCrSi powder is milled by using high energy ball milling (HEBM) process and later 30% of Cr3C2 powder is added. Microstructural features and phase analysis of milled powders, as-coated and microwave fused coatings are inspected by using SEM with EDS and XRD process respectively. The coatings before and after fusing are tested for microhardness and bond strength by using a Vickers microhardness and universal tensile machines respectively. Dry sliding wear behavior of coatings before and after fusing is conducted against alumina counter face at ambient and elevated temperatures, also normal load is varied. The wear mechanism of both coatings is examined by employing XRD, SEM-EDS techniques. The fused coatings exhibit lower friction and better wear resistance compared with as-deposited coatings. The detailed results of each test of their coatings are discussed in this paper. © 2018 IOP Publishing Ltd.Item Hot corrosion behaviour of HVOF sprayed Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) coatings in presence of Na2SO4-40%V2O5 at 650 °c(IOP Publishing Ltd custserv@iop.org, 2019) Reddy, N.C.; Koppad, P.G.; Reddappa, H.N.; Ramesh, M.R.; Babu, E.R.; Varol, T.Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) coatings were deposited on gas turbine based ASTM B265 titanium (Ti-15) and AISI 420 stainless steel (MDN-420) substrate materials using HVOF technique. Thermocyclic hot corrosion tests were carried out at 650 °C in molten salt environment of Na2SO4-40%V2O5 for about 50 cycles. Thermogravimetric analysis was carried out to study the hot corrosion kinetics of uncoated and coated titanium and stainless steel substrates. The weight gain per unit area showed that the coated substrate materials displayed better resistance to hot corrosion when compared with that of uncoated substrate materials. The surface morphology of uncoated and coated substrate materials were analysed using scanning electron microscopy and elemental analysis. The formation of different types of oxides and compounds were analysed using x-ray diffraction. The uncoated substrates surface showed microspalling at several regions while coated substrates surface were composed of protective oxide layers. The presence of ternary NiCr2O4 protective oxides on the surface of Ni3Ti + (Cr3C2 + 20NiCr) coated substrates leads to reduction in the diffusion of corrosive species inside the coating. © 2019 IOP Publishing Ltd.Item Effect of microwave heating on microstructure and elevated temperature adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2 coating(Elsevier B.V., 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This research reports the improvement of high-temperature sliding wear resistance of a grade 15 titanium alloy protected by an HVOF sprayed CoMoCrSi-Cr3C2 coating. The coatings have been tested in as-sprayed condition and after a post-deposition microwave heating step. The powder feedstock has been manufactured by high energy ball milling. X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) equipped with the Energy Dispersive Spectroscopy (EDS) methods were used for coatings characterization. Surface roughness, microhardness, adhesion strength, and porosity of coatings were also measured. The wear test was conducted at an applied load of l0 N and 20 N with varying temperatures of 200 °C, 400 °C, and 600 °C under dry sliding conditions. Co3Mo2Si, Co7Mo6, Mo3Si, Co3Mo, and Co2Mo3 were the intermetallic laves phases generated in the CoMoCrSi feedstock during HEBM process. The microwave-fused coating exhibited metallurgical bonding, homogeneous structure, less porosity, and greater hardness as compared to as-sprayed coating. Microwave-treated coating revealed better wear property than an as-sprayed coating. This was mainly due to the intermetallic formation and metallurgical bonding in coatings. The fused coatings exhibit tribo-oxide layers during sliding action which was the main phenomenon of improving the wear resistance of the fused composite coatings. © 2019 Elsevier B.V.