Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item EFFECT of LASER POST-TREATMENT on MICROSTRUCTURAL and SLIDING WEAR BEHAVIOR of HVOF-SPRAYED NiCrC and NiCrSi COATINGS(World Scientific, 2022) Naik, T.; Mathapati, M.; Prasad, C.D.; Nithin, H.S.; Ramesh, M.R.In this study, NiCrC and NiCrSi coatings are deposited on the MDN 310 steel using High-Velocity Oxy-Fuel (HVOF) process. Laser Surface Melting (LSM) post-heat treatment is carried out on as-sprayed coatings using Laser Engineered Net Shaping (LENSTM) with a power of 300W. The characteristics of both coatings in terms of mechanical and metallurgical properties have been investigated. The thicknesses of the as-sprayed NiCrC and NiCrSi coatings are in the range of 170-200μm. Laser-treated NiCrC and NiCrSi coatings exhibit a thickness range of 162-185μm, respectively. The microstructure of laser-treated NiCrC-300W coating clearly shows a dendrite-like structure, whereas the laser-treated NiCrSi coating exhibits hard layer and columnar homogeneity. Microhardness of as-sprayed NiCrC coating is 515±15 HV0.3 and that of NiCrSi coating is 645±25 HV0.3. Microhardness of laser-treated NiCrC coating is 720±30 HV0.3 and that of NiCrSi coating is 890±15 HV0.3. Dry sliding wear tests are conducted at room temperature (RT) and 400°C with 10-N and 20-N loads. The wear rates at 400°C temperature of laser-treated NiCrC and NiCrSi coatings produced are slightly below (1-2.2)×10-3mm3/m and (0.8-1.6)×10-3mm3/m, respectively. Laser-treated coatings produced better dry sliding wear behavior compared with as-sprayed coatings owing to dense microstructure. Formation of SiC phase in NiCrSi coating imparts high wear and frictional resistance compared to the NiCrC coating. © 2022 World Scientific Publishing Company.Item 3D printing of functionally graded nanocomposites: An investigation of microstructural, rheological, and mechanical behavior(John Wiley and Sons Inc, 2024) Kumar, S.; Rajath, S.; Shivakumar, N.D.; Ramesh, M.R.; Doddamani, M.Manufacturing functionally graded material through 3D printing is challenging owing to the deposition of different materials with different thermal properties in each layer, leading to a higher thermal gradient between deposited and depositing layers, resulting in improper bonding between them and, hence, reduced mechanical properties. This study focuses on 3D printing of functionalized multi-walled carbon nanotubes (MWCNTs)/high-density polyethylene (HDPE)-based lightweight functionally graded nanocomposites (FGNCs) and their investigation for microstructural, rheological, physical, and mechanical properties. Functionalized MWCNTs (0.5% → 5%) are initially compounded with widely utilized HDPE to develop nanocomposites (H0.5→H5 pellets) for extruding filaments for 3D printing. 3D-printed FGNC samples are investigated through scanning electron microscopy (SEM), rheology, density, tensile, and flexural tests. SEM and rheology confirm the homogeneous dispersion of the filler in HDPE and the processing parameters suitability in blending, extrusion, and 3D printing. Complex viscosity (η*), loss modulus (E″), and storage modulus (E′) of FGNCs increase, while the damping decreases with the MWCNTs rise in the graded layers. Density results revealed the highest weight saving potential (~12%) of FGNC-2 (H1–H3–H5), showing great weight saving potential. Tensile and flexural properties rise when the MWCNTs content rises in the graded layer. The FGNC-2 showed the highest tensile strength and moduli, 37.12% and 90.41% higher than HDPE. Flexural strength and moduli are also found to be the highest for FGNC-2, 28.57%, and 26.83% higher than HDPE. The highest specific moduli and strength are found for FGNC-2, 46.16% and 44.14% higher than HDPE, respectively. Experimental findings are found to be strongly in agreement with numerical findings. 3D-printed FGNC-2 demonstrated the best flexural and tensile characteristics with the lowest weight and hence can be used to make practical parts and structures that need variable stiffness. Highlights: FGNCs functionally graded n anocomposites are concurrently 3D printed. FGNC-2 exhibited the highest weight saving potential of 12%. FGNC-2 showed 90.41% and 37.12% enhanced tensile modulus and strength. FGNC-2 displayed 28.57% and 26.83% improved flexural strength and modulus. FGNCs exhibited better mechanical performance than the homogeneous NCs. © 2024 Society of Plastics Engineers.Item Microstructural evolution and cyclic oxidation behavior of HVOF-sprayed NiCrSi and NiCrC coatings on T11 steel(Elsevier Inc., 2024) Medabalimi, S.; Hebbale, A.M.; Singh, R.; Desai, V.; Ramesh, M.R.This study analyzes NiCrSi and NiCrC coatings developed on low alloy ferritic stainless steel (grade T11) through the HVOF spraying technique. The coatings were characterized by their phase constitution, microstructure, cyclic oxidation behavior, and hardness. X-ray diffraction (XRD) analysis confirmed the presence of the NiCr solid solution matrix as the primary phase in both coatings. Moreover, the microstructure of the NiCrSi coating included the hard intermetallic compounds like Cr?Si and Ni?Si and the NiCrC coating contained the hard phases like Cr?C? and Ni?C which improved the hardness and the wear resistance of the coatings. Microhardness measurements revealed that the coatings had an average hardness of 300 ± 50 HV, significantly greater than the substrate hardness of 225 ± 25 HV. Cyclic oxidation tests were carried out at 700 °C revealed that both the coatings showed a lower weight gain than the uncoated substrate, suggesting enhanced oxidation resistance. This was because the protective oxide layers like Cr?O? and SiO? in the NiCrSi coating and Cr?O? and NiO in the NiCrC coating were formed. X-ray analysis establish ed. the presence of these oxides, which inhibited oxygen penetration through the coatings and provided additional protection against oxidation. Therefore, the study revealed that both NiCrSi and NiCrC coatings have good mechanical and oxidation resistance properties, which make them suitable for high-temperature applications where there is a need for improved durability, wear resistance, and protection against oxidation. © 2024Item A microstructural study and high-temperature oxidation behaviour of plasma sprayed NiCrAlY based composite coatings(Elsevier B.V., 2025) Hebbale, A.M.; Ramesh, M.R.; Petr?, J.; Chandramouli, T.V.; Srinath, M.S.; Shetty, R.K.In this study, the development and performance evaluation of plasma sprayed NiCrAlY based coatings, such as NiCrAlY, NiCrAlY + Al?O? and NiCrAlY + YSZ on T91 steel substrates for high temperature applications is carried out. Microstructural features, phase composition and oxidation resistance under cyclic oxidation at 800 °C of the coatings were characterized. Analysis of the XRD confirmed the formation of protective phases such as Cr?O?, Ni?Al and NiAl, and the improvement observed in the coating's performance was due to the addition of Al?O? and YSZ. Oxidation resistance was improved for the NiCrAlY + Al?O? coating through the formation of a dense Al?O? oxide layer, but the NiCrAlY + YSZ coating was superior in terms of thermal stability and spallation resistance, because YSZ has low thermal conductivity and high thermal shock resistance. Composite coatings showed improved cyclic oxidation behavior and microstructural analysis revealed reduced porosity and enhanced integrity. The results demonstrate that the addition of Al?O? and YSZ in the NiCrAlY coatings leads to capability of tailoring NiCrAlY–based coatings for high temperature industrial applications with improved durability and oxidation protection. © 2025 The Author(s)Item Microstructural Evolution of Mg-Zn-Gd Alloy Using Equal Channel Angular Pressing to Enhance Mechanical and Corrosion Properties(Springer, 2025) Rokkala, U.; Patil, A.; Bontha, S.; Ramesh, M.R.; Balla, V.K.; Srinivasan, A.Equal channel angular pressing (ECAP) was used on the Mg-Zn-Gd alloy in this study to improve its corrosion and mechanical properties. Microstructural and phase analysis reveal that, after ECAP, a substantial grain refinement occurred, and secondary phases were observed. The grain size of the as-cast (AC) sample is reduced from 20 ± 1 to 0.88 ± 0.6 µm, attributed to dynamic recrystallization. The mechanical properties of the ECAP sample were significantly improved when compared to the AC sample. An improvement in the microhardness (43%), ultimate tensile strength (73%), yield strength (76%), and ductility (50%) were observed for the ECAP sample. A decrease in the corrosion rate was observed for ECAP sample (9 ± 1 mm/year) compared to the AC (16 ± 2 mm/year) sample. The grain refinement and crystallographic orientation of the ECAP samples contributed to the enhancement of corrosion resistance. © ASM International 2025.