Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine(Elsevier Ltd, 2016) Bharath Kumar, B.R.; Doddamani, M.R.; Zeltmann, S.E.; Gupta, N.; Ramesh, M.R.; Ramakrishna, S.Rapid production of high quality components is the key to cost reduction in industrial applications. The present work is the first attempt of manufacturing syntactic foams, hollow particle filled lightweight composites, using an industrial scale injection molding machine. High density polyethylene (HDPE) is used as the matrix material and fly ash cenospheres are used as the filler. Development of syntactic foams with cenospheres serves dual purpose of beneficial utilization of industrial waste fly ash and reduction in the cost of the component. The pressure and temperature used in the injection molding process are optimized to minimize fracture of cenospheres and obtain complete mixing of cenospheres with HDPE. The optimized parameters are used for manufacturing syntactic foams with 20, 40 and 60 wt.% cenospheres. With increasing cenosphere content, density and strength reduce and modulus increases. Surface modification of constituents results in rise in strength with increasing filler content. A theoretical model based on a differential scheme is used to estimate the properties of cenospheres by conducting parametric studies because of inherent difficulties in direct measurement of cenosphere properties. The potential for using the optimized injection molding process is demonstrated by casting several industrial components. © 2015 Elsevier Ltd.Item Evaluation of mechanical properties for nickel based steel produced by metal injection moulding and sintered through conventional and microwave method(Italian Association of Chemical Engineering - AIDIC aidic@aidic.it, 2018) Veeresh Nayak, C.; Ramesh, M.R.; Desai, V.; Kumar Samanta, S.K.Metal injection moulding is a near net shape manufacturing technique. It developed from traditional plastic injection moulding and powder metallurgy process. The process involved mixing of metal powder and binder, injection moulding, debinding and sintering of moulded samples. Microwave process indicated critical consideration towards exceptional highlights, regards to, heating and sintering the various grouping of metals with the huge preferred perspective, control rate, and similarity, low ecological dangers. The samples consist of SS316L+WC-CrC-Ni metal powder and binders, low-density polyethylene (LDPE), paraffin wax (PW), stearic acid (SA) and polyethylene glycol (PEG 600). In the present study, the injection moulded green parts are exposed to high-intensity microwave fields operates at a frequency of 2.45 GHz. for sintering of MIM samples. The whole process time of the microwave-assisted sintering was remarkably less than conventional sintering. The sintering of SS316L+WC-CrC-Ni compact showed better results than those produced by sintering with conventional heating. The current study evaluates the effect of the conventional and microwave sintering on mechanical properties. © © 2018, AIDIC Servizi S.r.l.Item Evaluation of Wear Behaviour of Metal Injection Moulded Nickel Based Metal Matrix Composite(Springer Netherlands rbk@louisiana.edu, 2019) Veeresh Nayak, V.N.; Ramesh, M.R.; Desai, V.; Kumar Samanta, S.K.Metal injection moulding (MIM) is a near-net shape manufacturing technology for producing intricate parts, cost-effectively. MIM comprises combined techniques of plastic injection moulding and powder metallurgy. The present study focused on the development of the binder and fabrication of defect free MIM component. A wax-based binder system consisting of paraffin wax (PW), low density polyethylene (LDPE), polyethylene glycol (PEG-600) and stearic acid was established for MIM of NiCrSiB (70% Wt.) + Cr3C2-NiCr (30% Wt.) nickel based metal matrix composite (NMMC) powder. The feedstock was characterised through rheological properties at different temperatures. Injection temperature was determined from the rheological investigation of the feedstock having the 56% powder loading and 44% binder by volume. Sintering process was carried out with the temperature cycle in the range of 1250–1300 ?C under hydrogen purged atmosphere. The MIM components showed good and acceptable shrinkage in linear dimensions. The mechanical properties and wear behaviour of NMMC was studied using a pin-on-disc apparatus with alumina disc.Tests were performed under dry sliding conditions at room temperature and elevated temperatures of 200 and 400 ?C. Results shows that wear rate is maximum at 400 ?C for 40 N and lowest at room temperature for 10 N. Further wear mechanism was analysed using scanning electron microscope (SEM). © 2018, Springer Science+Business Media B.V., part of Springer Nature.Item Sintering metal injection molding parts of tungsten-based steel using microwave and conventional heating methods(SAGE Publications Ltd info@sagepub.co.uk, 2019) Veeresh Nayak, C.; Ramesh, M.R.; Desai, V.; Kumar Samanta, S.K.In recent years, the near net shape metal injection molding process combines desirable features of plastic injection molding and powder metallurgy processes to gain high strength-to-weight ratio for manufacturing complex-shaped parts. The metal injection molding process consists of mixing, molding, debinding, and sintering. Microwave processing has attracted much attention in global research because of its unique features such as its ability to heat and sinter a wide variety of metals and its significant advantages in energy efficiency, processing speed, and compatibility. Also, it presents few environmental risks and can produce refined microstructures. The injected samples to be sintered are composed of fine tool steel metal powder and binders, stearic acid, paraffin wax, low-density polyethylene, and polyethylene glycol (600). In recent years, microwave-assisted post-treatment is considered a novel method for processing green parts. In this work, the green parts are subjected to high-intensity microwave fields which operate at a frequency of 2.45 GHz. Metal injection molding compacts were sintered using multi-mode microwave radiation. The sintering of a metal injection molding compact by microwaves has hardly been reported. The metal injection molding compact showed better results than those produced by sintering with conventional heating. This study evaluates the effect of conventional sintering and microwave sintering on mechanical properties. By optimizing the sintering process, increased sintered hardness, a more homogeneous microstructure, and greater shrinkage were obtained using microwave-assisted sintering. © IMechE 2018.