Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item High-temperature wear and frictional behavior of partially oxidized Al with NiCr composite coating(Institute of Physics Publishing helen.craven@iop.org, 2019) Medabalimi, S.R.; Ramesh, M.R.; Kadoli, R.The influence of composite coating in improving wear and frictional behavior from room temperature to 600 °C was investigated. Partially oxidized Al powder was prepared with a flame spray process by spraying pure Al powder into distilled water. The composite powder is the mixture of 30 weight percent of partially oxidized Al and 70 weight percent of NiCr alloy powder. The composite powder was subsequently coated on MDN321 steel by air plasma spray process. The composite coatings are characterized with respect to adhesion strength, porosity, micro-hardness, and density. Wear and frictional behavior of coatings are evaluated under disc speed of 1 and 2 m s-1, loads of 10, 20 and 30 N and 3000 m sliding distance. The test results indicated that at room temperature, frictional heat generated due to applied load produce three-body abrasion at the interface caused to increase the wear and friction in the coating. The oxide film formed at high temperature due to plastic deformation avoids surface degradation at the interface and reduce the wear and friction. The worn surfaces at 600 °C consist phases of ?-Al2O3, NiO, and Cr3O. These phases are contributing to improving the wear resistance of the coating more than 4-times compared to uncoated steels under varying load and sliding velocities. The coefficient of friction reduced with increase in temperature due to generated oxides act as lubricants at the interface. © 2019 IOP Publishing Ltd.Item Developing partially oxidized NiCr coatings using the combined flame spray and plasma spray process for improved wear behaviour at high temperature(Elsevier Ltd, 2021) Medabalimi, S.R.; Ramesh, M.R.; Kadoli, R.The powders of NiCrBSiFe and NiCr are partially oxidized using a flame spray process and are deposited on MDN321 steel substrate using a plasma spray process. The effect of partial oxidization on microstructure, microhardness, density, bond strength, and porosity of the coatings is analyzed. The friction and wear behaviour of the coatings was assessed using a pin-on-disc tribometer by varying loads (10, 20 and 30 N), sliding velocities (1, 2 m/s) and temperatures (RT, 200, 400 and 600 °C). Worn surfaces of NiCrBSiFe and NiCr coatings consist of oxide phases of SiO2, NiO, Cr2O3 and NiCr2O4 at elevated temperatures. These phases contributed to reducing the wear rate by five folds in coated steels compared to uncoated steels at 600 °C. The wear rate in coating decreases with an increase in temperature. The coefficient of friction was reduced gradually with the temperature in coatings and substrate. The wear rate coefficient of NiCr coating was 1.7 times higher than the NiCrBSiFe coating. © 2021 Elsevier B.V.Item MICROSTRUCTURE AND TRIBOLOGICAL PERFORMANCE OF SELF-LUBRICATE CLADDING PRODUCED BY TUNGSTEN INERT GAS AND MICROWAVE HYBRID HEATING TECHNIQUES(World Scientific, 2022) Gudala, S.; Ramesh, M.R.; Siva Shanmugam, N.S.; Srinath, M.S.The wear reduction of moving components is highly desirable because wear limits their reliability and service life, mainly at elevated temperatures. This study produced thick clads of NiCrSiB/WC/MoS2/BaF2 by tungsten inert gas (TIG) and microwave hybrid heating (MHH) cladding techniques, which were compared for microstructural and high-temperature tribological properties. The clad samples were subjected to sliding contact using a pin on disc tribometer at 200°C, 400°C, 600°C under 20 and 40N load. The worn surface was analyzed using FESEM, XRD and three-dimensional (3D) profilometer. The experimental results revealed a significant effect of the TIG current and MHH exposure time on the microhardness value, which predominantly depends on the morphological characteristics. The average hardness of TIG clads was found to be 1.2 times higher than the MHH clad. Because of the MoS2 and BaF2 encapsulation, the continuous lubricant layer formation compensated for improved wear resistance with good reliability and longer service life. This work provides significant insights into the wear behavior of TIG and MHH clads at elevated temperatures and the prospective applications in turbines, where inadequate wear resistance of titanium alloy is the major concern for its use. © 2022 World Scientific Publishing Company.Item Microstructure and Wear Behavior of Self-Lubricating Microwave Clads Deposited on Titanium Alloy(Springer, 2022) Gudala, S.; Ramesh, M.R.; Srinath, M.S.In this work, composite clads (NiCrSiB/WC/Ag/hBN and NiCrSiB/WC/MoS2/hBN) have been successfully developed using microwave cladding technique on titanium 31 substrate. The clads were characterized by field emission scanning electron microscope (FESEM), electron backscatter diffraction (EBSD), x-Ray diffraction (XRD) analysis. The developed clads were free from porosity, defects, and other thermal distortion effects. Furthermore, due to the uniform distribution of hard phases, clads achieved uniform hardness across the clad depth. The convective currents of the molten pool improved metallurgical bonding with the substrate. Because of the volumetric heating, the deviation of microhardness values in the clad was found to be low. The tribological properties of the clads were tested against an Al2O3 counterbody using a pin on disc tribometer. The results showed that incorporating solid lubricants (Ag/hBN and MoS2/hBN) into the nickel-based alloy significantly improved tribological properties. The wear rate and coefficient of friction decreased as the temperature increased from 200 to 600 °C. It was demonstrated that anti-wear and lubricating capability of both clad could be improved at elevated temperatures by doping Ag, MoS2, and hBN solid lubricants. © 2022, ASM International.Item Phase evolution and high-temperature wear behavior of non-equiatomic metastable CoCrNiTiMox HEA coatings fabricated by high-velocity oxy-fuel technique(Elsevier Ltd, 2023) Addepalli, S.N.; Joladarashi, S.; Ramesh, M.R.The current research aims to enhance the tribological performance of maraging steels at high temperatures by surface modification techniques. CoCrNiTiMox (x; molar fraction, x = 0.5, 1.5) high-entropy alloy (HEA) coatings with dense lamellar microstructures were deposited onto maraging steels using high-velocity oxy-fuel spray (HVOF). In order to achieve a uniform distribution of constituent elements for thermal spray deposition, mechanical alloying was employed to synthesize the HEA feedstock. The phases and microstructure of the synthesized HEA powder, as-sprayed coatings, and worn surfaces were examined using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The as-sprayed HEA coatings exhibited metastability, with a BCC phase solid solution, NiTiO3 spinel, and an intermetallic MoNi phase for CoCrNiTiMo0.5 and Co2Mo3 phase for CoCrNiTiMo1.5. The average microhardness of CoCrNiTiMo0.5 and CoCrNiTiMo1.5 HEA coatings were 841 ± 62 HV0.3 and 952 ± 23 HV0.3, respectively. The specific wear rate and friction coefficients of CoCrNiTiMox HEA coatings exhibited a decreasing trend with an increase in temperature, owing to the formation of tribofilms on the worn surface. X-ray diffraction studies revealed the formation of NiMoO4 spinel for CoCrNiTiMo0.5 and MoO2, Co3O4 phases for CoCrNiTiMo1.5 HEA at a wear temperature of 600 °C. The investigation of worn surfaces showed a transformation in wear mechanisms from abrasive wear at room temperature to oxidative wear with mild fatigue at elevated temperatures. © 2023 Elsevier LtdItem Effect of Microwave Hybrid Heating on High-Temperature Adhesive Wear Behavior of High-Velocity Oxygen Fuel-Sprayed WC-CrC-Ni and WC-Co/NiCrFeSiB Coatings(Springer, 2023) Medabalimi, S.; Ananthu, M.R.; Gudala, S.; Ramesh, M.R.HVOF-processed coatings are chemically inhomogeneous and are not metallurgically bonded to the substrate. As a result, components coated with HVOF experience considerable material degradation during sliding wear. Microwave hybrid heating (MHH) is a novel surface modification technique for modifying the as-sprayed properties of the coating. Hence, this paper investigates and compares the wear and frictional behavior of HVOF as-sprayed coatings against MHH samples of WC-CrC-Ni and WC-Co/NiCrFeSiB coatings at elevated temperatures. MHH had a significant impact on wear rate and coefficient of friction by optimizing the porosity, integrated oxide phases and intersplat cohesion strength of the coatings. A modified domestic oven was used to perform MHH on HVOF-coated samples for 5 min at 1200 °C. Wear tests were performed using a pin-on-disk tribometer from room temperature to 200, 400, and 600 °C with Al2O3 disk as a counterface. SEM/EDS and XRD were utilized to examine the microstructural characterization of the coatings and substrate. Both the coatings showed higher wear resistance than the substrate at all temperatures. The WC-Co/NiCrFeSiB coating produced an oxide layer on the worn surfaces and integrated WC, CoWO4, and Fe2SiO4 splats, enhancing wear resistance. The MHH WC-CrC-Ni coating formed Cr2O3 and NiWO4 phases on the worn surfaces, increasing the intersplat cohesion strength between matrix and carbide splats, lowering the overall wear rate. After MHH, the wear rate of a substrate and WC-CrC-Ni coating was 3.5 and 1.12 times more at room temperature and 8.07 and 2.92 times more at 600 °C than WC-Co/NiCrFeSiB coating. © 2022, ASM International.Item Microstructure and elevated temperature wear behavior of HVOF-sprayed SS304L stainless-steel coating(Springer Nature, 2025) Medabalimi, S.; Gudala, S.; Rokkala, U.; Hebbale, A.M.; Ramesh, M.R.The paper aims to investigate the performance of the SS304L stainless steel coating on wear properties by varying load, temperature and velocity. Stainless-steel coatings were fabricated by high-velocity oxy-fuel spraying (HVOF) on superfer800. Surface morphology, elemental distribution and phase analysis were expressed by SEM, EDS, and XRD, respectively. The porosity, average surface roughness, and average microhardness of HVOF stainless steel coating are 2%, 7 µm, and 1167 ± 54 HV0.3, respectively. The wear rate of stainless-steel coating is 0.5 × 10?3 mm3/m at 600 °C with 20 N loads, which is about 16 times lower than the substrate. Adhesion and abrasion are the main wear mechanisms of HVOF stainless steel coatings during high-temperature tests. Comparing to superfer800 substrate, stainless steel coatings showed superior wear resistance at all the loads, temperature and velocities. © The Author(s) 2025.Item Microstructure, Mechanical Properties, and Tribological Properties of Fe-Based Composite Coatings Reinforced with WC-Co and Cr3C2(Springer, 2025) Chandramouli, T.V.; Joladarashi, S.; Ramesh, M.R.; Rahman, M.R.Fe-based (stainless steel 316L) coatings are widely employed in the aerospace, chemical processing, petrochemical, and marine industries owing to their low and stable price, excellent corrosion resistance, and durability. However, at elevated temperatures, their performance is limited due to wear. Thus, the current investigation incorporates tungsten carbide (WC-Co) and chromium carbide (Cr3C2) into the Fe-based coating to enhance its wear resistance at high temperatures. SS316L reinforced by 30% of WC-Co and Cr3C2 by mechanical mixture, then sprayed using high-velocity oxy fuel spraying method. Coating characteristics, such as microstructures and phase analysis, were measured using FESEM/EDS and XRD. Coating density, microhardness, and bond strength were examined by water immersion, Vickers indentation, and ASTM C-633 methods, respectively. A ball-on-disk tribometer was employed to conduct wear examination at various temperatures (25, 300, and 600 °C) and loads (10 and 30 N) against the alumina counter body. The wear rate and friction coefficient of SS316L-30%WC-Co decrease from 25 to 600 °C, while the wear rate of SS316L-30%Cr3C2 increases with temperature up to 300 °C and then decreases at 600 °C. The oxide phase adheres strongly to underlying surfaces forming a protective layer (Cr2O3, NiWO4, Fe2O3, and NiMO4), changing the mode of wear mechanism. At higher temperatures and loads, the coating exhibited oxidation modified adhesive wear, and coatings provide excellent wear resistance along with reduction in friction. This research provides a novel approach for future standardization and evaluation of coatings on metal alloys for industrial applications. © ASM International 2024.