Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Experimental investigation and optimization of machining parameters for sustainable machining(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2018) Varghese, V.; Ramesh, M.R.; Dupadu, D.A detailed investigation on the effects of cutting parameters and different cooling environments on machinability of austenitic stainless steel AISI 304 is presented in this study. The need for sustainable manufacturing and better surface quality urged to explore the merits of cryogenic cooling over the other conventional cooling techniques. The end milling experiments were designed based on three parameter and three-level design considering dry, wet, and cryogenic machining environments to have a comparative study. The machinability studies such as surface roughness, tool wear, cutting forces, chip morphology, and chip reduction coefficient were investigated and compared with different machining environments. The machining parameters were optimized using Taguchi-based grey relational analysis. The cryogenic machining had the most influence on milling of AISI 304 steel and resulted in the reduction of cutting forces, surface roughness, and chip reduction coefficient in comparison with the conventional wet and dry machining. © 2018, © 2018 Taylor & Francis.Item Effect of cutting parameters on tool wear, cutting force and surface roughness in machining of MDN431 alloy using Al and Fe coated tools(Institute of Physics Publishing helen.craven@iop.org, 2019) V Badiger, P.V.; Desai, V.; Ramesh, M.R.; Prajwala, B.K.; Raveendra, K.Thin solid films are used in cutting tools in order to improve its performance, reduce tool wear and improve tool life. Cathodic arc evaporation is the state of art PVD technique widely accepted in industries for the development of thin solid films. The turning cutting tool inserts are coated with AlCN/AlC and FeCrN monolayer thin solid films using cathodic arc evaporation technique. Quality characteristics of thin films are estimated using Calo and VDI3198 tests. Thickness of the coatings are found to be 1.430 and 1.475 ?m for AlCN/AlC and FeCrN coatings respectively and adhesion quality of HF1 is attained. Performance of the thin solid films are evaluated in machining MDN431 steel with range of cutting speed (59-118 m min-1), feed rate (0.062-0.125 mm/rev) and depth of cut (0.2-0.4 mm). Experiments are performed based on full factorial design and regression analysis. Optimization of the process parameters is carried out using combined techniques of desirability and Particle swarm optimisation (PSO). The objective of the study is to establish correlation between machining parameters with cutting force, tool wear and surface roughness. Optimal process parameter for least cutting force and surface roughness are obtained for coatings. ANN has been adopted to improve the coefficient of determination (CoD) and capability of predictive regression models. ANN trained model and mathematical regression models are adequate to predicted the responses, which follows the experimental data with minimum absolute error. The AlCN/AlC coatings exhibited lower cutting forces and surface roughness than FeCrN coated tools. Tool wear was reduced by 3.62 times in AlCN/AlC and 1.63 times in FeCrN coated tools compared to uncoated tool which is due to increased hardness and elastic modulus of the coating. © 2018 IOP Publishing Ltd.Item Influence of deep cryogenic treatment on performance of cemented carbide (WC-Co) inserts during dry end milling of maraging steel(Elsevier Ltd, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.Cryogenic treatment has developed as a technique to improve the life of the cutting tool, especially tungsten carbide inserts. The present study investigates the effect of cryogenic treatment of cemented carbide (WC-Co) inserts at the different soaking period of 18 h (CT-18), 24 h (CT-24) and 32 h (CT-32) at a sub-zero temperature of ?196 °C. The soaking period plays a crucial role in improving the wear resistance of the cryogenically treated tools. It is vital to determine the critical soaking period for the cryogenic treatment of cemented carbides. The mechanical and metallurgical characterization of cryogenically treated cemented carbide insert is carried out to understand the changes in the microstructure, grain size, chemical composition, microhardness and electrical conductivity after cryogenic treatment. The end milling experiments on maraging steel under dry environment are carried out using cryogenically treated inserts at different holding time and untreated inserts (UT). The machining performance of treated and untreated inserts are compared with respect to tool wear, surface roughness and cutting forces. The results revealed that cryogenic treatment is effective in resisting tool wear even at high spindle speeds. The cryogenically treated inserts exhibited higher tool life, better surface finish and lower cutting forces during machining at different spindle speeds. The optimum soaking time for cryogenic treatment of WC-Co inserts is found to be 24 h (CT-24) beyond which there is no improvement in microhardness and wear resistance. © 2018Item Effects of Wire Electro-Discharge Machining Process Parameters on the Machined Surface of Ti 50 Ni 49 Co 1 Shape Memory Alloy(Springer Netherlands rbk@louisiana.edu, 2019) Soni, H.; Narendranath, S.; Ramesh, M.R.Wire electro-discharge machining is one of the advanced machining processes which can machine all conductive materials without changing their internal properties. Pulse on time and servo voltage are the most influential process parameters of wire electro-discharge machining. In the present study, attempts have been made to study the effects of these process parameters on the machined surface of Ti 50 Ni 49 Co 1 shape memory alloy by adopting a two process parameters experimental design approach. Cutting speed and surface roughness were considered as output parameters; surface crack density, microhardness and XRD analysis were carried out at the higher and lower values of these parameters. Higher surface crack density has been found at high values of cutting speed (125 ?s pulse on time and 20 V servo voltage) while it is lower at the lower value of cutting speed (105 ?s pulse on time and 60 V servo voltage). Moreover, a harder surface was found near the machined surface. By XRD analysis it was found that the crystal size of the WED machined surface was reduced at high T on and lower SV. © 2018, Springer Science+Business Media B.V., part of Springer Nature.Item Investigation on the performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of maraging steel under dry, wet and cryogenic environments(Elsevier Ltd, 2019) Varghese, V.; K, A.; Ramesh, M.R.; Dupadu, D.The present study investigates the machining performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of MDN 250 maraging steel. The mechanical and metallurgical characterization is carried out to determine the properties of the PVD coatings developed. The end milling experiments under dry, wet and cryogenic environment is carried out using coated uncoated inserts (UC) at different spindle speeds to evaluate the machining performance in terms of tool life, surface roughness and cutting forces. The coated inserts showed higher tool life, better surface finish, and low cutting forces during machining at different spindle speeds. It is found that the AlCrN coating had a better wear resistance and machining performance in comparison with AlTiN coating. The cryogenic environment reduced the surface roughness & cutting force and improved the tool life of the cutting tool compared to conventional dry and wet environment. It is revealed that coated tools along with cryogenic cooling can be employed for high-speed machining applications. © 2019 The Society of Manufacturing EngineersItem Experimental investigation of cryogenic end milling on maraging steel using cryogenically treated tungsten carbide-cobalt inserts(Springer, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.The cryogenic machining and cryogenic treatment have already emerged as the sustainable manufacturing process of the future generation. The cryogenic treatment improves the cutting tool life, but the high cutting temperature developed during high-speed machining reduces the effect of cryogenic treatment of cutting tool. This study investigates the possible improvements in cutting tool life by combining cryogenic cooling and cryogenic treatment. The authors believe that these two techniques can replace conventional machining approaches using dry and wet machining conditions using coated carbide tools. The tungsten carbide-cobalt inserts are cryogenically treated (CT) at a soaking temperature of ? 195.8 °C for a period of 24 h and are used to evaluate milling performance under dry, wet, and cryogenic cutting environments. The machining experiments are conducted on maraging steel MDN 250 using one factor at a time approach by varying spindle speed and keeping feed rate and depth of cut as constant. The cutting force, surface roughness, tool wear, and subsurface microhardness are some of the machining responses evaluated and compared with an untreated cutting tool (UT). The tool life improved up to 24% during cryogenic machining using CT tools at a spindle speed of 270 rpm. © 2019, Springer-Verlag London Ltd., part of Springer Nature.