Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
12 results
Search Results
Item High temperature corrosion behaviour of HVOF sprayed WC-CrC-Ni coatings(Inderscience Publishers, 2016) Somasundaram, B.; Kadoli, R.; Ramesh, M.R.; RAMESH, C.S.The present work aims to study the hot corrosion resistance of high velocity oxy-fuel (HVOF) sprayed WC-CrC-Ni coating developed on three types of boiler tube materials such as SA213-T22, MDN-310 and Superfer 800 H steels. Hot corrosion studies were conducted in a molten salt environment of Na2SO4-60%V2O5 at 700°C and thermogravimetric analysis was used to establish kinetics of corrosion. Corrosion kinetics of coated steels followed nearly parabolic behaviour and showed a lower corrosion rate in comparison to uncoated alloys. It is concluded that corrosion is restricted to the external surface of the coating and the formation of thick scale composed of oxides of Cr, Ni and their spinel oxides, acts as a diffusion barrier to the transportation of corrosive species into the coating. The carbides of tungsten and chromium uphold the strength of the coating. © © 2016 Inderscience Enterprises Ltd.Item Cyclic Oxidation and Hot Corrosion Behavior of Plasma-Sprayed CoCrAlY + WC-Co Coating on Turbine Alloys(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Nithin, H.S.; Vijay, D.; Ramesh, M.R.Components in energy-producing systems suffer a variety of degradation processes such as oxidation and molten salt-induced corrosion as a consequence of complex multi-component gaseous environment. Coatings provide a composition that will grow the protective scale at high temperatures having long-term stability. Plasma spraying was used to deposit CoCrAlY + WC-Co composite coatings on turbine alloys of Hastelloy X and AISI 321. The thermocyclic oxidation behavior of coated alloys was investigated in static air and in molten salt (Na2SO4-60%V2O5) environment at 700 °C. The thermogravimetric technique was used to approximate the kinetics of oxidation in 50 cycles, each cycle consisting of heating and cooling. X-ray diffraction and SEM/EDAX techniques are used to characterize the oxide scale formed. Coated alloys showed a lower corrosion rate as compared to uncoated alloys. The coatings subjected to oxidation and hot corrosion showed slow scale growth kinetics. Preferential oxidation of Co, Cr, W and its spinel blocks the transport of oxygen and corrosive species into the coating by providing a barrier, thereby making the oxidation rate to reach steady state. As compared to the substrate alloys, coatings show better hot corrosion resistance. © 2018, ASM International.Item Hot corrosion behaviour of HVOF sprayed Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) coatings in presence of Na2SO4-40%V2O5 at 650 °c(IOP Publishing Ltd custserv@iop.org, 2019) Reddy, N.C.; Koppad, P.G.; Reddappa, H.N.; Ramesh, M.R.; Babu, E.R.; Varol, T.Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) coatings were deposited on gas turbine based ASTM B265 titanium (Ti-15) and AISI 420 stainless steel (MDN-420) substrate materials using HVOF technique. Thermocyclic hot corrosion tests were carried out at 650 °C in molten salt environment of Na2SO4-40%V2O5 for about 50 cycles. Thermogravimetric analysis was carried out to study the hot corrosion kinetics of uncoated and coated titanium and stainless steel substrates. The weight gain per unit area showed that the coated substrate materials displayed better resistance to hot corrosion when compared with that of uncoated substrate materials. The surface morphology of uncoated and coated substrate materials were analysed using scanning electron microscopy and elemental analysis. The formation of different types of oxides and compounds were analysed using x-ray diffraction. The uncoated substrates surface showed microspalling at several regions while coated substrates surface were composed of protective oxide layers. The presence of ternary NiCr2O4 protective oxides on the surface of Ni3Ti + (Cr3C2 + 20NiCr) coated substrates leads to reduction in the diffusion of corrosive species inside the coating. © 2019 IOP Publishing Ltd.Item Comparative investigation of coating and friction stir processing on Mg-Zn-Dy alloy for improving antibacterial, bioactive and corrosion behaviour(Elsevier B.V., 2021) Rokkala, U.; Jana, A.; Bontha, S.; Ramesh, M.R.; Balla, V.K.Magnesium based alloys are well-known materials for temporary implant applications. However, failures due to early degradation and bacterial infection are limiting their applications. To overcome these problems, in the present work a Mg-Zn-Dy alloy based composite surface was prepared using coating and friction stir processing (FSP) techniques. Herein, hydroxyapatite (HA) and silver (Ag) particles were deposited on Mg-Zn-Dy alloy to obtain HA and Ag coated surface (C-HAg). Later, FSP was carried out on the C-HAg surface to develop a Mg-Zn-Dy alloy based composite surface (F-HAg). Field emission scanning electron microscope (FESEM) and energy dispersive X-ray analysis (EDS) confirm the mixing of HA and Ag particles with the Mg-Zn-Dy substrate. Antibacterial studies reveal that both C-HAg and F-HAg samples inhibit Escherichia coli and Staphylococcus aureus bacteria. In vitro cytotoxicity study indicates that the both samples are non-toxic in nature. Results of in vitro corrosion study reveal a significant reduction (72%) in corrosion rate of F-HAg sample when compared to C-HAg sample. The F-HAg samples showed simultaneous improvement in corrosion resistance and antibacterial properties with good biocompatibility. The results of this study indicate that the developed composite surface is a promising material for antibacterial and biodegradable implant applications. © 2021 Elsevier B.V.Item Hot corrosion behavior of plasma sprayed FeCrNiC and FeCrNiC/Cenosphere coatings on ASTM-SA213-T22 steel(Elsevier Ltd, 2022) Hanumanthlal, S.; Siddaraju, C.; Ramesh, M.R.; Thirtha Prasada, H.P.; Somasundaram, B.The steel alloys tubes used to manufacture boilers which are used in high temperature environment in thermal power plants are often subjected to high temperature corrosion. Therefore, to protect the surface of boiler tubes, protective coatings are used to counter the corrosion. In this work FeCrNiC and FeCrNiC/Cenosphere coatings deposited on T22 boiler tube steel using atmospheric plasma spraying. Thermocyclic hot corrosion studies were examined in a liquid salt condition of Na2SO4-60%V2O5 for 17 cycles of 51 h at 600 °C on uncoated and coated steel. Thermogravimetric practice was utilized to build up the kinetics of hot corrosion of uncoated and coated steel. As-coated samples are studied for microstructure and microhardness. The X-ray diffraction(XRD), Scanning electron microscopy(SEM)/Energy dispersive spectroscopy(EDX), and X-ray mapping characterization techniques were used to analyse the corrosion products. It was observed that FeCrNiC/Cenosphere coated steel showed better hot corrosion resistance than the uncoated steels. Parabolic rate constant values of coated steel are lower in comparison to the uncoated steels. Better resistance is provided by high-temperature stability of mullite, alumina, defensive glassy oxide layer of silicon, titanium and spinels of chromium and carbon that is formed at elevated temperatures. © 2021Item Investigation of thermally sprayed NiCrAlY/TiO2and NiCrAlY/Cr2O3/YSZ cermet composite coatings on titanium alloys(Institute of Physics, 2022) Madhu Sudana Reddy, G.; Prasad, C.D.; Patil, P.; Shetty, G.; Ramesh, M.R.; Nageswara Rao, T.The present work investigates the hot corrosion behavior of thermally sprayed 65 pct NiCrAlY + 35 pct TiO2 and 65 pct NiCrAlY + 30 pct Cr2O3 + 5 pct YSZ coatings on titanium 15 alloys. The coatings on the titanium 15 alloy substrates exhibit a near-uniform, dense, and adherent microstructure with a porosity of 2.7 to 2.9%. Thermogravimetric studies are made to examine the hot corrosion performance of coatings in a molten salt environment of Na2SO4 + 60%V2O5 at the temperature of 700 °C for 50 cycles. One cycle is carried out by heating for a period of one hour and cooling the sample at ambient conditions. The corrosion products are analyzed based on scanning electron microscopy, energy dispersive analysis, and X-ray diffraction techniques to study the morphology, phase composition, and abundance of the high-temperature corrosion constituents. The bare titanium-15 alloy, 65 pct NiCrAlY + 35 pct TiO2 coating and 65 pct NiCrAlY + 35 pct Cr2O3 + 5 pct YSZ coating produced a weight gain of 307.92 mg cm-2, 42.16 mg cm-2 and 44.02 mg cm-2 respectively after the period of 50 cycles. The effective resistance of the coatings is due to the formation of Ni3V2O8, NiCr2O4, Cr2O3 & AlV2O4 phases. © 2022 IOP Publishing Ltd.Item High Temperature Corrosion Behavior of High Velocity Oxy Fuel Sprayed NiCrMoFeCoAl-30%SiO2 and NiCrMoFeCoAl-30%Cr2O3 Composite Coatings on ASTM SA213-T22 Steel in a Coal-fired Boiler Environment(Materials and Energy Research Center, 2022) Patil, V.G.; Somasundaram, B.; Kandaiah, S.; Ramesh, M.R.; Patil, S.High-velocity oxy fuel (HVOF) sprayed coatings can improve the corrosion resistance of bare ASTM SA213-T22 boiler steel. In this report, we have investigated the NiCrMoFeCoAl-30%SiO2 and NiCrMoFeCoAl-30%Cr2O3 composite coatings were deposited on bare ASTM SA213-T22 boiler steel for corrosion protection. High-temperature corrosion studies were conducted in a molten salt (Na2SO4-60%V2O5) environment at 700ºC under thermo-cyclic conditions. The as-sprayed composite coatings are characterized for microstructure and mechanical properties. The thermo-gravimetric method was utilized to understand the kinetics of corrosion. Characterization of the corrosion products was examined by using scanning electron microscope (SEM)/ Energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) techniques. The obtained results suggest both the composite coatings are favorable to corrosion resistance over the bare ASTM SA213-T22 boiler steel. The NiCrMoFeCoAl-30%Cr2O3 composite coating was concluded to present a superior corrosion resistance in the high-temperature corrosion environment because of the uniform distribution of the composite coating matrix and the development of protective protection Cr2O3 in the scale. The molten salt heat-treated chromium oxide containing coating shows good corrosion stability than the silica composite. This could be attributed to the high temperature assisted formation metal chromates, chromites and oxide layers. © 2022 Materials and Energy Research Center. All rights reserved.Item Cyclic Oxidation and Hot-Corrosion Behavior of HVOF-Sprayed NiCrAl Coating on Industrial Boiler Tube Steels(Springer, 2024) Ramesh, M.R.; Medabalimi, S.; Rupanagudi, R.S.; Prasad, C.D.; Sollapur, S.B.At high temperatures, coatings provide a protective scale development on surfaces to maintain long-term stability. In the current study, ASTM-SA210-Grade A1 (GrA1) and ASTM-SA213-T-11 (T11) boiler tube steels were coated with NiCrAl alloy with high-velocity oxy-fuel (HVOF) to prevent oxidation and hot corrosion. For hot corrosion and oxidation, 50 cycles at 900°C were taken into account. Additionally, tests of hot-corrosion behavior were conducted in an atmosphere containing molten salt (Na2SO4-60%V2O5), while tests of oxidation behavior were conducted in static air. The kinetics of oxidation were calculated using the thermogravimetric method. Using XRD, EPMA, and SEM/EDAX methods, the produced oxide scales were characterized. The oxidation rate of NiCrAl-coated steels was found to be lower than that of uncoated steels. The coated steels subjected to oxidation in air exhibit slow scale growth kinetics and oxides of α-Al2O3 and Cr2O3 on the outermost surface, while accelerated oxidation caused by the molten salt exhibits metastable Al2O3. Along the nickel-rich splat boundary, Cr and Al were formed a preferential oxidation, which prevents other oxygen from entering the coating via pores and voids, resulting in steady-state oxidation. © The Minerals, Metals & Materials Society 2024.Item Fabrication and Characterization of Silicon Dioxide-Reinforced Polydimethylsiloxane Composite Coating for Corrosion Protection of Galvanized Iron(SAE International, 2024) Kumar, P.; Ramesh, M.R.; Doddamani, M.The present work highlights the significance of nanocomposite coatings for their ease of processing and applicability in combating corrosion. Ongoing research is dedicated to the development of an effective nanocomposite hydrophobic coating. A hydrophobic nanocomposite coating was deposited on galvanized iron (GI) using a sol-gel route with polymethylsiloxane (PDMS) reinforced with nano-SiO2. Surface morphology and chemical composition analysis, conducted with scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDAX) and Fourier transform infrared spectroscopy (FTIR), revealed the coating's structural and compositional attributes. The resulting hydrophobic coating exhibits a water contact angle (WCA) of 104.1°, indicating a 30.45% increase compared to bare GI. Subsequent to these characterizations, the adhesion of the coated GI, rated as 4B per ASTM D3359, is followed by commendable resistance to corrosion, as evidenced by electrochemical tests. The corrosion rate for the coated GI sheet is notably low, at 62.78 × 10-3 mpy, underscoring its anti-corrosive efficacy. © 2024 SAE International.Item Synthesis and characteristics of Fe/Ni/Cr oxide nanoparticles/PLA hybrid composite coatings on Mg–Zn–Ca alloy(Elsevier Editora Ltda, 2025) Kumar, P.; Kudva S, A.; T, A.; S, R.; Ramesh, M.R.; Prabhu, A.; Anne, G.Biodegradable materials research is dominated by magnesium and alloys thereof due to their excellent compatibility with biological barriers and biomechanical strength. Despite this, the rapid degradation of these materials in the physiological environment is the primary obstacle hindering their utilization in biomedical applications. This issue must be resolved before considering their use in clinical applications. To improve resistance towards corrosion and enhance biological efficacy and compatibility, the surfaces were coated with polylactic acid (PLA) using dip-coating. In this study, iron (Fe), nickel (Ni), and chromium (Cr) oxide nanoparticles from the Coleus amboinicus extract are synthesized and mixed with PLA to develop hybrid composite coatings, which are then applied onto the Mg–4Zn–1Ca alloy. Coleus amboinicus is known for its various medicinal properties, including immunoregulatory effects, antimicrobial activity, anti-inflammatory properties, and potential use in treating sepsis and other ailments. The extracted FeNiCr was used the develop composite coatings on Mg–4Zn–1Ca alloy. The coating improves biocompatibility, antibacterial properties, and overall performance of biomedical implants. These composite coatings were evaluated for their morphological and optical characteristics using a scanning electron microscope (SEM), 3-D non-contact profilometer, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The corrosion characteristics of developed samples were measured by electrochemical corrosion in standard simulation body fluid (SBF) at 37 °C. Furthermore, cytocompatibility of the PLA hybrid composites on osteoblast cells and apoptosis detection using acridine orange-ethidium bromide. Our developed coating showed ratings of 5B and 4B were obtained for FeNiCr/PLA NC- ball burnished (BB) Mg and FeNiCr/PLA nano composite (NC)–Mg samples, respectively, demonstrating the exceptional coating strength and the substrate. The corrosion rate of the FeNiCr/PLA NC-BB-Mg sample (0.02890 mm/y) is two-fold times increased against comparison with the H Mg sample (0.00012 mm/y). Cytocompatibility indicates their cytocompatibility for bone implant applications. © 2025 The Authors