Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Ramesh, M.R.Subject: search.filters.subject.Atmospheric temperature

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    Elevated Temperature Solid Particle Erosion Performance of Plasma-Sprayed Co-based Composite Coatings with Additions of Al2O3 and CeO2
    (Springer New York LLC barbara.b.bertram@gsk.com, 2017) Nithin, H.S.; Desai, V.; Ramesh, M.R.
    In this paper, investigation into solid particle erosion behavior of atmospheric plasma-sprayed composite coating of CoCrAlY reinforced with Al2O3 and CeO2 oxides on Superni 76 at elevated temperature of 600 °C is presented. Alumina particles are used as erodent at two impact angles of 30° and 90°. The microstructure, porosity, hardness, toughness and adhesion properties of the as-sprayed coatings are studied. The effects of temperature and phase transformation in the coatings during erosion process are analyzed using XRD and EDS techniques. Optical profilometer is used for accurate elucidation of erosion volume loss. CoCrAlY/CeO2 coating showed better erosion resistance with a volume loss of about 50% of what was observed in case of CoCrAlY/Al2O3/YSZ coating. Lower erosion loss is observed at 90° as compared to 30° impact angle. The erosion mechanism evaluated using SEM micrograph revealed that the coatings experienced ductile fracture exhibiting severe deformation with unusual oxide cracks. Reinforced metal oxides provide shielding effect for erodent impact, enabling better erosion resistance. The oxidation of the coating due to high-temperature exposure reforms erosion process into oxidation-modified erosion process. © 2017, ASM International.
  • No Thumbnail Available
    Item
    Microstructure and tribological characteristics of APS sprayed NiCrBSi/flyash cenosphere/Cr2O3 and NiCrBSi/flyash cenosphere/Mo composite coatings at elevated temperatures
    (Institute of Physics Publishing helen.craven@iop.org, 2019) Nagabhushana, N.; Rajanna, S.; Mathapati, M.; Ramesh, M.R.; Koppad, P.G.; Reddy, N.C.
    In the present investigation NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo composite coatings are developed using atmospheric plasma spray technique on superni 76 alloy. Coatings are characterized in terms of microstructure, phase analysis, and microhardness. Tribological properties of the coatings are evaluated using a pin on disc tribometer. Test is conducted under dry sliding conditions at room temperature, 200 °C, 400 °C, and 600 °C respectively. Microstructure and worn surfaces of the coatings are analyzed by utilizing Scanning Electron Microscope (SEM) where in phase analysis is carried out using x-ray diffractometer (XRD). XRD results revealed the presence of ?-Ni as primary phase along with Ni3B, Cr7C3, SiO2 and Al2O3 as minor phases in both the NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo coatings. Among the two coatings, Mo composite coating exhibited lower porosity and higher microhardness. The friction coefficient of both the coatings decreased with increasing temperature. The wear rate is found to decrease at lower temperatures but increased at a higher temperature (>400 °C) for Cr2O3 composite coating wherein Friction coefficient is decreased with increase in the temperature for Mo composite coatings. The worn surface analysis conducted revealed abrasive wear at lower temperatures while the transition from abrasive to adhesive is observed at higher temperatures. © 2019 IOP Publishing Ltd.
  • No Thumbnail Available
    Item
    Evaluation of Wear Behaviour of Metal Injection Moulded Nickel Based Metal Matrix Composite
    (Springer Netherlands rbk@louisiana.edu, 2019) Veeresh Nayak, V.N.; Ramesh, M.R.; Desai, V.; Kumar Samanta, S.K.
    Metal injection moulding (MIM) is a near-net shape manufacturing technology for producing intricate parts, cost-effectively. MIM comprises combined techniques of plastic injection moulding and powder metallurgy. The present study focused on the development of the binder and fabrication of defect free MIM component. A wax-based binder system consisting of paraffin wax (PW), low density polyethylene (LDPE), polyethylene glycol (PEG-600) and stearic acid was established for MIM of NiCrSiB (70% Wt.) + Cr3C2-NiCr (30% Wt.) nickel based metal matrix composite (NMMC) powder. The feedstock was characterised through rheological properties at different temperatures. Injection temperature was determined from the rheological investigation of the feedstock having the 56% powder loading and 44% binder by volume. Sintering process was carried out with the temperature cycle in the range of 1250–1300 ?C under hydrogen purged atmosphere. The MIM components showed good and acceptable shrinkage in linear dimensions. The mechanical properties and wear behaviour of NMMC was studied using a pin-on-disc apparatus with alumina disc.Tests were performed under dry sliding conditions at room temperature and elevated temperatures of 200 and 400 ?C. Results shows that wear rate is maximum at 400 ?C for 40 N and lowest at room temperature for 10 N. Further wear mechanism was analysed using scanning electron microscope (SEM). © 2018, Springer Science+Business Media B.V., part of Springer Nature.