Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Praseodymium doped ceria as electrolyte material for IT-SOFC applications(Elsevier Ltd, 2018) Shajahan, I.; Ahn, J.; Nair, P.; Medisetti, S.; Patil, S.; Niveditha, V.; Uday Bhaskar Babu, G.; Prasad Dasari, H.P.; Lee, J.-H.Praseodymium-doped ceria (PDC, Ce0.9Pr0.1O2) electrolyte material for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been successfully synthesised by EDTA-citrate method. From X-Ray diffraction (XRD), fluorite structure along with a crystallite size of 5.4 nm is obtained for PDC nanopowder calcined at 350 °C/24 h. Raman spectroscopy confirmed the structure, presence of oxygen vacancies with the manifestation of the main peak at 457 cm?1 and with a secondary peak at 550 cm?1. From Transmission Electron Microscopy (TEM) analysis, the average particle size is around 7–10 nm and selected area electron diffraction (SAED) patterns further confirmed the fluorite structure of PDC nanopowder. The PDC nanopowder displayed a BET surface area of 65 m2/g with a primary particle size of ?13 nm (calculated from BET surface area). Dilatometer studies revealed a multi-step shrinkage behaviour with the multiple peaks at 522, 1171 and 1461 °C which may be originated due to the presence of multiple size hard agglomerates. The PDC electrolyte pellet sintered at 1500 °C displayed an ionic conductivity of 1.213E-03 S cm?1 along with an activation energy of 1.28eV. Instead of a single fluorite structure, XRD of sintered PDC pellet showed multiple structures (Fluorite structure (CeO2) and cubic structure (PrO2). © 2018 Elsevier B.V.Item Effect of fuel and solvent on soot oxidation activity of ceria nanoparticles synthesized by solution combustion method(KeAi Communications Co., 2019) Patil, S.S.; Prasad Dasari, H.P.Effect of fuel (glycine and urea) and solvent (water, acetone and ethanol) on the soot oxidation activity of ceria nanoparticles synthesized by solution combustion method is carried out in the present study. X-ray diffraction (XRD) patterns displayed a fluorite structure and the Tauc's plot obtained from UV-Diffusive Reflectance spectroscopy (UV-DRS) showed that the band gap value was around 2.9–3.1 eV for the synthesized ceria nanoparticles irrespective of the fuel and solvent used. Ceria nanoparticles synthesized using glycine and acetone resulted in lower crystallite size, higher facet ratios ([1 0 0]/[1 1 1] and [1 1 0]/[1 1 1]) and higher lattice strain than compared to other solvents and fuels and thus resulted in better soot oxidation activity (T50 = 416 °C). The present synthesis method has played a significant role in improving the reactive facet ratios, providing lower crystallite size and high lattice strain. © 2019Item Dilatometer studies of praseodymium doped ceria: Effect of synthesis methods on sintering behaviour(Elsevier Ltd, 2020) Shajahan, I.; Prasad Dasari, H.P.; Govardhan, P.Praseodymium-doped ceria (Ce0.9Pr0.1O2, PDC), as an electrolyte material for IT-SOFCs, is investigated with respect to the effect of synthesis method and a detailed analysis was carried out to understand the effect on crystallite size, morphology, specific surface area and sintering behaviour. The various synthesis routes such as microwave assisted co-precipitation method, room temperature co-precipitation method and EDTA-citrate complexing method was adopted for the synthesis of praseodymium doped ceria-based nano-materials. XRD pattern confirms the fluorite-type crystal structure of ceria and Raman spectroscopy analysis confirms the structure with the presence of oxygen vacancies. PDC synthesised by microwave assisted co-precipitation method using isopropyl alcohol as solvent exhibited better sintering activity, reduced the sintering temperature and promoted the densification rate when compared to other synthesis methods with uni-model shrinkage behaviour with shrinkage maxima at 765 °C. Based on two sintering models (CHR/Dorn method), the initial stage sintering mechanism was investigated in the present study and confirmed that the grain boundary diffusion (m = 2) as the dominant mechanism and the activation energy was found to be 116 kJ/mol (CHR model) and 176 kJ/mol (Dorn Method) for initial stages of sintering for PDC material synthesised by microwave assisted co-precipitation method using isopropyl alcohol as solvent. © 2019 Elsevier B.V.Item A Negative Effect of Niobium-Doped Ceria on Soot Oxidation Activity‡(John Wiley and Sons Inc, 2022) Patil, S.S.; Naik, S.; Ramesh, M.D.; Harshini, H.; Prasad Dasari, H.P.Niobium-doped ceria catalysts were synthesized to study soot oxidation activity. X-Ray diffraction (XRD) and Raman analysis of the samples revealed the presence of a fluorite structure of CeO2 for all the doped samples. The T50 temperature of the pure CeO2 sample was more significant than that of bare soot. The high catalytic activity of the CeO2 catalyst can be attributed to the low crystallite size, high facet ratio, and the large Brunauer-Emmett-Teller (BET) surface area as compared to Nb-doped samples. The activation energy calculated by both Ozawa and KAS methods were found to be low for CeO2 when compared to Nb-doped samples. CeO2 resulted in better soot oxidation activity with low activation energy. © 2022 Wiley-VCH GmbHItem Diesel soot oxidation over Mn–Pr–Ce oxide catalysts: structural changes and the impact of Mn doping(Royal Society of Chemistry, 2025) Patil, S.S.; Prasad Dasari, H.P.; Shirasangi, R.; Harshini, H.The soot oxidation activity of manganese-doped ceria-praseodymium catalysts, synthesized via solution combustion synthesis, was evaluated. The analyses performed with XRD and Raman spectroscopy indicated that the Mn-doped CP catalysts displayed the typical fluorite structure of CeO2. The addition of Mn to CP led to a reduction in crystallite size from 14 nm to below 10 nm. The F2g Raman active mode of fluorite-structured Ce and the oxygen vacancies resulting from the addition of Mn and Pr (bands B 560 cm–1 to 580 cm–1) were consistently observed across all Mn-doped CP catalysts. 15 and 20 Mn-CP exhibited an additional secondary phase identified as Mn2O3. The analysis of BET surface area and BJH pore size revealed that the Mn-doped CP catalysts exhibited both micro and mesoporous characteristics. The H2-TPR and O2-TPD profiles indicated enhanced reducibility resulting from the incorporation of Mn and Pr into CeO2-doped catalysts. The improved T50 (365 ± 1 1C) for the 5 Mn-CP catalytic system is primarily due to its increased specific surface area of 45 m2 g–1 and the presence of active surface adsorbed oxygen species identified in the XPS and O2-TPD studies. 5 Mn-CP exhibited the lowest activation energy value compared to all other Mn-doped catalysts. © 2025 The Author(s)