Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
13 results
Search Results
Item Ceria-samarium binary metal oxides: A comparative approach towards structural properties and soot oxidation activity(Elsevier B.V., 2018) Anjana, A.P.; Geethu, J.; P, M.R.; Prasad Dasari, H.P.; Lee, J.-H.; Harshini, H.; Bhaskar Babu, G.U.Binary metal oxides of CeO2-Sm2O3 (CSx, x varies from 10 to 90 mol%) along with pure CeO2 and Sm2O3 were synthesised successfully by the EDTA-Citrate method. From XRD, Raman spectroscopy and UV–vis DRS results, the whole composition of metal oxides exist in three phases: (fluorite phase (F) (CS10-CS30), bi-phase (fluorite (F) + cubic (C)) (CS30-CS90) and cubic phase (C) (Sm2O3)). For CSx samples, the calculated band gap energy values obtained from the UV–vis DRS results were in between 3.0–5.1 eV and fluorite phase samples (CS10–CS30) displayed lower band gap energy values (3.04–3.07 eV) than compared to the samples in other phases. Similarly, from XPS analysis, fluorite phase samples (CS10–CS30) showed higher surface oxygen vacancy concentration than compared to samples in other phases. Catalytic activity for soot oxidation is carried out on CSx samples, and the T50 temperature is in between 480–540 °C. Fluorite phase samples (CS10 CS30) showed higher surface area, lower degree of agglomeration, lower band gap energy, higher oxygen vacancy concentration and better catalytic activity for soot oxidation. Among all the CSx samples, CS10 sample displayed highest surface area (38 m2/g), lowest degree of agglomeration (0.36), lowest band gap energy (3.04 eV), highest oxygen vacancy concentration (64%) and highest soot oxidation activity (T50 = 480 °C). The order of the soot oxidation activity of CSx samples followed the same trend of band gap energy values. © 2018 Elsevier B.V.Item Praseodymium doped ceria as electrolyte material for IT-SOFC applications(Elsevier Ltd, 2018) Shajahan, I.; Ahn, J.; Nair, P.; Medisetti, S.; Patil, S.; Niveditha, V.; Uday Bhaskar Babu, G.; Prasad Dasari, H.P.; Lee, J.-H.Praseodymium-doped ceria (PDC, Ce0.9Pr0.1O2) electrolyte material for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been successfully synthesised by EDTA-citrate method. From X-Ray diffraction (XRD), fluorite structure along with a crystallite size of 5.4 nm is obtained for PDC nanopowder calcined at 350 °C/24 h. Raman spectroscopy confirmed the structure, presence of oxygen vacancies with the manifestation of the main peak at 457 cm?1 and with a secondary peak at 550 cm?1. From Transmission Electron Microscopy (TEM) analysis, the average particle size is around 7–10 nm and selected area electron diffraction (SAED) patterns further confirmed the fluorite structure of PDC nanopowder. The PDC nanopowder displayed a BET surface area of 65 m2/g with a primary particle size of ?13 nm (calculated from BET surface area). Dilatometer studies revealed a multi-step shrinkage behaviour with the multiple peaks at 522, 1171 and 1461 °C which may be originated due to the presence of multiple size hard agglomerates. The PDC electrolyte pellet sintered at 1500 °C displayed an ionic conductivity of 1.213E-03 S cm?1 along with an activation energy of 1.28eV. Instead of a single fluorite structure, XRD of sintered PDC pellet showed multiple structures (Fluorite structure (CeO2) and cubic structure (PrO2). © 2018 Elsevier B.V.Item Surface morphology and phase stability effect of Ceria-Hafnia (CHx) binary metal oxides on soot oxidation activity(Elsevier B.V., 2018) Anjana, A.P.; Prasad Dasari, H.P.; Harshini, H.; Babu, G.U.B.CeO2-HfO2 (CHx) binary metal oxides over whole composition range (0–100%) are synthesised using the EDTA-Citrate method and calcined at 600 °C/5 h. From XRD analysis, the sample series are classified as fluorite (F) phase for CH10-CH30, hybrid (F + M) phase for CH40-CH90 and monoclinic (M) phase for CH100 sample, respectively and the results were further confirmed using Raman spectroscopy. From SEM analysis, a clear surface morphology change is noticed for fluorite, hybrid and monoclinic phases of the CHx binary metal oxides. Further, Selected Area Electron Diffraction (SAED) analysis also confirmed the single and hybrid phases of CHx binary metal oxides. The soot oxidation for the CHx binary metal oxides displayed high catalytic activity for Fluorite phase (CH10 ? CH30) samples and a decrease in catalytic activity is noticed for the Hybrid phase (CH40 ? CH90) samples. The change in catalytic activity coincides with the change in the surface morphology and phase change for the CHx binary metal oxides. Among the Fluorite phase samples, CH10 sample displayed the highest catalytic activity (T50 = 430 °C) with higher surface area (29 m2/g), lower particle size (26 nm), lower degree of agglomeration (? = 2.8) higher surface oxygen concentration (44%). Isothermal-Time-on-stream (ITOS) analysis also showed that the CH10 sample can achieve T50 in a shorter time than compared to other CHx binary metal oxides. Surface morphology and phase stability can also play as key descriptors in screening CHx binary metal oxides for soot oxidation activity. © 2018 Elsevier B.V.Item Effect of ionic radius on soot oxidation activity for ceria-based binary metal oxides(John Wiley and Sons Ltd vgorayska@wiley.com Southern Gate Chichester, West Sussex PO19 8SQ, 2019) Anjana, A.P.; Prasad Dasari, H.P.; Harshini, H.; Babu, G.U.B.CeO2 (C) along with binary metal oxides of Ce0.9M0.1O2-? (M = Sn, Hf, Zr, Gd, Sm, and La; CT, CH, CZ CG, CS, and CL) are synthesized using the EDTA–citrate method. Samples having an ionic radius smaller (CT, CH, and CZ) and larger (CG, CS, and CL) than Ce4+ are classified separately, and their soot oxidation activity is analyzed. The incorporation of dopant is confirmed from lattice constant variation in X-ray diffraction result. The critical descriptors for the activity are dopant nature (ionic radius and oxidation-state), single-phase solid solution, lattice strain, reactive (200) and (220) planes, Raman intensity ration (Iov/IF2g), optical bandgap, reducibility ratio, and surface oxygen vacancy. Smaller ionic radius, isovalent dopants (CH and CZ) create a defect site by lowering the optical bandgap along with improved surface oxygen vacancy concentration and thus enhanced soot oxidation activity. Aliovalent dopant with larger ionic radius shows the involvement of lattice oxygen in oxidation reaction by charge compensation mechanism. CL showed the highest activity amongst larger ionic radius samples. © 2019 Curtin University and John Wiley & Sons, Ltd.Item Effect of fuel and solvent on soot oxidation activity of ceria nanoparticles synthesized by solution combustion method(KeAi Communications Co., 2019) Patil, S.S.; Prasad Dasari, H.P.Effect of fuel (glycine and urea) and solvent (water, acetone and ethanol) on the soot oxidation activity of ceria nanoparticles synthesized by solution combustion method is carried out in the present study. X-ray diffraction (XRD) patterns displayed a fluorite structure and the Tauc's plot obtained from UV-Diffusive Reflectance spectroscopy (UV-DRS) showed that the band gap value was around 2.9–3.1 eV for the synthesized ceria nanoparticles irrespective of the fuel and solvent used. Ceria nanoparticles synthesized using glycine and acetone resulted in lower crystallite size, higher facet ratios ([1 0 0]/[1 1 1] and [1 1 0]/[1 1 1]) and higher lattice strain than compared to other solvents and fuels and thus resulted in better soot oxidation activity (T50 = 416 °C). The present synthesis method has played a significant role in improving the reactive facet ratios, providing lower crystallite size and high lattice strain. © 2019Item Dilatometer studies of praseodymium doped ceria: Effect of synthesis methods on sintering behaviour(Elsevier Ltd, 2020) Shajahan, I.; Prasad Dasari, H.P.; Govardhan, P.Praseodymium-doped ceria (Ce0.9Pr0.1O2, PDC), as an electrolyte material for IT-SOFCs, is investigated with respect to the effect of synthesis method and a detailed analysis was carried out to understand the effect on crystallite size, morphology, specific surface area and sintering behaviour. The various synthesis routes such as microwave assisted co-precipitation method, room temperature co-precipitation method and EDTA-citrate complexing method was adopted for the synthesis of praseodymium doped ceria-based nano-materials. XRD pattern confirms the fluorite-type crystal structure of ceria and Raman spectroscopy analysis confirms the structure with the presence of oxygen vacancies. PDC synthesised by microwave assisted co-precipitation method using isopropyl alcohol as solvent exhibited better sintering activity, reduced the sintering temperature and promoted the densification rate when compared to other synthesis methods with uni-model shrinkage behaviour with shrinkage maxima at 765 °C. Based on two sintering models (CHR/Dorn method), the initial stage sintering mechanism was investigated in the present study and confirmed that the grain boundary diffusion (m = 2) as the dominant mechanism and the activation energy was found to be 116 kJ/mol (CHR model) and 176 kJ/mol (Dorn Method) for initial stages of sintering for PDC material synthesised by microwave assisted co-precipitation method using isopropyl alcohol as solvent. © 2019 Elsevier B.V.Item Effect of sintering aids on sintering kinetic behavior of praseodymium doped ceria based electrolyte material for solid oxide cells(Elsevier Ltd, 2020) Shajahan, I.; Prasad Dasari, H.P.; Saidutta, M.B.The present study investigates the effect of sintering additives (Li, Co, Fe, and Mg) on the sintering kinetic behavior of the praseodymium-doped-ceria (PDC) electrolyte of solid oxide electrolyzer cell. 3Li-PDC, 3Co-PDC, 3Fe-PDC, and 3 Mg-PDC pellets were obtained from the synthesis of PDC nano-powder by microwave-assisted co-precipitation method using isopropyl alcohol as a solvent and followed by sintering additive wetness impregnation method. Linear shrinkage and shrinkage rate data suggest a positive sintering effect for 3Li-PDC and 3Co-PDC pellets and a negative sintering effect for 3 Mg-PDC and 3Fe-PDC pellets than compared to PDC pellets alone. The addition of lithium as a sintering additive (3Li-PDC) had reduced the sintering temperature of PDC from 1100 °C to 850 °C. For PDC, 3Li-PDC, 3Co-PDC, 3Fe-PDC and 3 Mg-PDC pellets sintered at 1100 °C, 850 °C, 1000 °C, 1200 °C, 1100 °C for 2 h resulted in a relative density of 93.6 ± 0.25, 95.8 ± 0.45, 95.0 ± 0.20, 92.7 ± 0.10, and 94.5 ± 0.10%, respectively. The XRD patterns of the sintered PDC pellets suggested a secondary phase formation (PrO2) in 3Co-PDC, 3Fe-PDC, and 3 Mg-PDC pellets indicating that the addition of these sintering aids results in poor solubility limit of Pr in CeO2. On the other hand, XRD patterns of PDC and Li-PDC sintered pellets displayed no secondary peak indicating good solid-solution formation. The activation energy of the 3Li-PDC pellet is obtained from CHR and Dorn methods and was found to be 182 kJ/mol and 196 kJ/mol. From the CHR method, for the 3Li-PDC pellet, the initial sintering behavior is by the grain boundary diffusion mechanism (m = ~2). © 2020 Hydrogen Energy Publications LLCItem A Negative Effect of Niobium-Doped Ceria on Soot Oxidation Activity‡(John Wiley and Sons Inc, 2022) Patil, S.S.; Naik, S.; Ramesh, M.D.; Harshini, H.; Prasad Dasari, H.P.Niobium-doped ceria catalysts were synthesized to study soot oxidation activity. X-Ray diffraction (XRD) and Raman analysis of the samples revealed the presence of a fluorite structure of CeO2 for all the doped samples. The T50 temperature of the pure CeO2 sample was more significant than that of bare soot. The high catalytic activity of the CeO2 catalyst can be attributed to the low crystallite size, high facet ratio, and the large Brunauer-Emmett-Teller (BET) surface area as compared to Nb-doped samples. The activation energy calculated by both Ozawa and KAS methods were found to be low for CeO2 when compared to Nb-doped samples. CeO2 resulted in better soot oxidation activity with low activation energy. © 2022 Wiley-VCH GmbHItem An investigation on copper-loaded ceria-praseodymium catalysts for soot oxidation activity and its kinetics(Springer Science and Business Media Deutschland GmbH, 2024) Patil, S.S.; Prasad Dasari, H.P.The Cu-loaded Ce-Pr catalyst series was successfully developed to study their performance on soot oxidation activity and its kinetic behavior. The doped samples showed a similar trend for cubic fluorite structure except for CuO, which possessed a monoclinic structure from the XRD analysis. Facet ratios [{100}/{111} and {110}/{111}] for the reactive planes were calculated from XRD spectra; the ratio was high for the 5 Cu-CP catalysts. The oxygen vacancy peaks were noticed from Raman spectra for the doped samples. 5 Cu-CP displayed the better catalytic activity of T50 = 402 °C, which may be attributed to high reactive planes and better reducibility. The addition of Cu showed a slight enhancement in catalytic activity compared to CP and pure Ce. The kinetic triplets were evaluated: the activation energy (Ea), pre-exponential factor (A), and the reaction model. Pure Ce displayed the lowest Ea and A values, whereas pure Cu showed high Ea and A values by all the methods. Graphical abstract: (Figure presented.) © The Author(s) under exclusive licence to Associação Brasileira de Engenharia Química 2023.Item Electrochemical characterization of electrolyte supported solid oxide electrolysis cell during CO2/H2O co-electrolysis(Springer Science and Business Media Deutschland GmbH, 2024) Shirasangi, R.; Prasad Dasari, H.P.; Saidutta, M.B.High-temperature co-electrolysis is studied on electrolyte-supported NiO-YSZ/NiO-SDC/ScSZ/LSCF-GDC/LSCF (NiO: Nickel Oxide, YSZ: Yttria-stabilized zirconia, SDC: Samarium-doped ceria, ScSZ: Scandia-stabilized zirconia, LSCF: Lanthanum Strontium Cobalt Ferrite, GDC: Gadolinium-doped ceria) button cell. Electrochemical impedance spectroscopy (EIS) was recorded under open-circuit voltage (OCV) and co-electrolysis mode over various operating conditions, including temperature, water vapor content, and applied voltage. Interfacial polarization resistance (Rp) is obtained from peak arcs located in the three regions: gas conversion resistance (Region I (0.01 to 0.1 Hz)), gas diffusion resistance (Region II (0.1 to 100 Hz)) and air electrode charge transfer resistance (Region III (100 to 10,000 Hz)). As the temperature increased from 700 to 850 oC, Rp decreased from 18.15 to 3.32 Ω.cm2 at 1.3 V for 10%CO2/3%H2O. From the Distribution of relaxation times (DRT) studies, one additional peak, P5 (fuel gas conversion or gas-phase diffusion in the pores of the air electrode), is observed, and Region III (100 to 10,000 Hz) consists of two additional peaks: P1 (ionic transport coupled with gas diffusion close to triple phase boundaries (TPBs)) and P2 (fuel electrode charge transfer reaction), which were not clearly distinguished from EIS. Region II dominates in the overall polarization resistance. At 800 oC, for 10%CO2/3%H2O, the Rp decreased from 6.78 to 4.82 Ω.cm2, with an increase in the applied voltage from 1.3 to 1.5 V. At 800oC/1.5 V, the Rp values are 4.41, 8.09, and 6.77 Ω.cm2 for H2O, CO2, and co-electrolysis. At 800 ºC/1.5 V, with an increase in the water vapor content from 3%H2O to 15%H2O, there is not much change in the Rp value; therefore, 10%H2O is sufficient. H2 consumption is between 23 and 36%, depending on the temperature at OCV. At 800 °C for (10%H2/10%CO2/10%H2O), co-electrolysis occurs at applied voltage, along with Reverse water gas shift (RWGS) reaction. Graphical Abstract: (Figure presented.) © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2024.