Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Heat transfer and solidification behaviour of modified A357 alloy(2007) Kumar, G.; Hegde, S.; Prabhu, K.N.Al-Si alloys are subjected to melt treatment like modification to improve their mechanical properties. Non-destructive technique like thermal analysis is generally used to assess the effectiveness of melt treatment. In the present study, the behaviour of the melt treated Al-7Si-Mg alloy (A357) during solidification with or without chilling was investigated using thermal analysis. Thermal analysis and heat transfer parameters were determined. Thermal analysis parameters were affected significantly by modification and chilling. Modification treatment resulted in the increase of cooling rate, heat evolved, casting/mould interfacial heat flux and eutectic growth velocity. A theoretical model based on undercooling from the equilibrium temperature during eutectic solidification was used to predict growth velocities and eutectic grain size. The eutectic grain sizes estimated using the model and those measured from casting microstructures were found to be in good agreement. © 2006 Elsevier B.V. All rights reserved.Item Modification of eutectic silicon in Al-Si alloys(2008) Hegde, S.; Prabhu, K.N.The mechanical properties of Al-Si alloys are strongly related to the size, shape and distribution of eutectic silicon present in the microstructure In order to improve mechanical properties, these alloys are generally subjected to modification melt treatment, which transforms the acicular silicon morphology to fibrous one resulting in a noticeable improvement in elongation and strength. Improper melt treatment procedures, fading and poisoning of modifiers often result in the structure which is far from the desired one. Hence it is essential to assess the effectiveness of melt treatment before pouring. A much investigated reliable thermal analysis technique is generally used for this purpose. The deviation from the standard curve in thermal analysis helps in assessing the level of refinement of the Si structure. In the present review an attempt is made to discuss various aspects of modification, including mechanism, interaction of defects and non-destructive assessment by thermal analysis. © 2008 Springer Science+Business Media, LLC.Item Effect of modification melt treatment and chilling on eutectic arrest temperature and time during solidification of A357 alloy(2011) Prabhu, K.N.; Hegde, S.Thermal analysis technique has been recognised as an efficient non-destructive tool to assess the degree of modification in Al-Si alloys. Apart from chemical modification, chilling refines the microstructure. This is particularly significant as majority of Al-Si alloys are cast in metallic moulds. In the present study, the interaction between chilling and modification melt treatment is investigated to assess their effect on thermal analysis parameters using computer aided cooling curve analysis. For modified alloys, the depression of the eutectic arrest temperature was significant at higher cooling rates. The eutectic arrest temperature and time were correlated with the cooling rate using a power law. High cooling regime in thermal analysis plots was attributed to the combined effect of chilling and modification melt treatment on heat transfer. © 2011 Institute of Materials, Minerals and Mining.Item Effect of chemical modification of Al-Si alloys on thermal diffusivity and contact heat transfer at the casting-chill interface(2012) Prabhu, K.N.; Jayananda; Hegde, S.The heat flow during the unidirectional downward solidification of Al-7Si and Al-12Si alloys was analyzed using thermal analysis technique and inverse modeling. Chills instrumented with thermocouples were brought into contact with a small pool of liquid metal so as to minimize the effect of convection caused by pouring and temperature gradients. Modification melt treatment resulted in an increase in the cooling rate of the solidifying casting near the casting-chill interfacial region. The corresponding interfacial heat flux transients were also found to be higher. The thermal diffusivities of alloys were measured using a laser pulse technique and were found to be higher for modified alloys. However, the increase in the heat flux transients was attributed mainly to the improvement in the casting-chill interfacial thermal contact condition brought about by the decrease in the surface tension of the liquid metal upon the addition of sodium. Copyright © 2012 by ASTM International.Item Effect of Mn on cooling behaviour and microstructure of chill cast Zn-Al (ZA8) alloy(2012) Ramesh, G.; Vishwanatha, H.M.; Prabhu, K.N.In the present work, the effect of manganese addition to ZA8 alloy on thermal analysis parameters, heat transfer and microstructure was investigated. The thermal analysis parameters were found to be significantly affected by chemical modification of ZA8 alloy. Cooling curve and differential scanning calorimetry analyses of modified alloy showed nucleation of new phase other than b dendrites. Chilling of modified alloy resulted in decreased liquidus temperature and enhanced eutectoid transformation. Further, chilling avoids the formation of intermetallic compounds in modified alloy. The heat flux transients were estimated using inverse modelling during solidification of unmodified and modified alloys against different chills. The peak heat flux decreased on addition of Mn to ZA8 alloy. Differential scanning calorimetry analysis indicated that the addition of Mn to ZA8 alloy decreases the heat of solidification. The addition of Mn to ZA8 alloy increased the contact angle, indicating decreased wettability of the modified alloy on the chill surface. The microstructure of ZA8 with Mn showed an increased amount of b phase and a decreased amount of eutectic. X-ray diffraction analysis confirmed the formation of MnAl6 intermetallics in Mn added ZA8 alloy. Chilling with chemical modification resulted in enhanced decomposition of b phase. © 2012 Institute of Materials, Minerals and Mining.Item Wetting Behavior and Heat Transfer of Aqueous Graphene Nanofluids(Springer New York LLC barbara.b.bertram@gsk.com, 2016) Nayak, U.V.; Prabhu, K.N.Aqueous graphene nanofluids having concentrations 0.01, 0.1, and 0.3 vol.% were used as heat transfer media during quenching of ISO 9950 inconel alloy probe. Contact angle measurements were carried out to assess the wettability of graphene nanofluids. Nanofluids showed better wettability compared to base water with over 16% reduction in their contact angles. The cooling performance of the quench media was assessed by cooling curve analysis during quenching of an instrumented inconel probe from 860 °C into the quench medium. Recorded temperature readings showed longer vapor phase stage during quenching with nanofluids. The severity of nanofluids was found to be lower relative to water. During quenching with nanofluids, the estimated spatiotemporal heat flux transients at the metal/quenchant interface showed that more heat was removed during the vapor phase stage of cooling. The present study brings out the possibility of using stable water-graphene nanoplatelet suspensions for quench heat treatment of steel components requiring cooling severity between water and oil/polymer quenchants. © 2016, ASM International.Item Thermal Analysis of Cerium-Treated Chill-Cast Al-23 Si Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Vijayan, V.; Prabhu, K.N.The influence of elemental cerium addition on the cooling curve parameters and microstructure of hypereutectic Al-23Si alloy was investigated in this work. The cooling rate of the treated and untreated alloy samples was varied by solidifying the melt against chills of different materials in a stainless-steel tube. The cooling curve was recorded and nucleation temperatures of various phases in the alloy were measured. The results show that the chilling improves the effectiveness of the modifier. The two main phases of the alloy, primary silicon and eutectic silicon, were nucleated at temperatures of about 661.2 and 571.6 °C, respectively. The addition of Ce to slowly cooled alloys resulted in an increase in undercooling temperature of both the phases, with a decrease in its nucleation temperature, whereas the same additions increased the nucleation temperatures in chilled alloys. Based on the thermal analysis results, a relation between thermal analysis parameter (? TG) and silicon particle size of the alloy was proposed. © 2018, ASM International.Item Effect of carbon black and titanium dioxide dispersants on solidification of multiwall carbon nanotube-added salt-based phase change material(ASTM International, 2021) Rajagopalan, S.; Prabhu, K.N.The effect of carbon black and titanium dioxide (TiO2) dispersants on solidification of potassium nitrate phase change material (PCM) with multiwall carbon nanotube (MWCNT) addition was investigated using the Fourier method of thermal analysis. On addition of 0.1 % of MWCNT, the solidification time of PCM decreased by 26 %, enhancing the heat release rates. A decrease in thermal diffusivity of the PCM was observed on addition of MWCNT particles. These benefits were observed to diminish over successive thermal cycles because of the agglomeration of MWCNT particles. To prevent the agglomeration of additives, dispersants such as carbon black and TiO2 were used. In the presence of carbon black, the nanosalt PCM retained all the cooling curve parameters over 10 thermal cycles, preventing the agglomeration of nanoadditives. On the other hand, the dispersant TiO2 significantly enhanced the thermal diffusivity property of PCM by virtue of its superior thermal conductivity. These are critical outcomes in development of nanosalt PCMs for thermal energy storage applications. © © 2021 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959 ASTM International is not responsible, as a body, for the statements and opinions expressed in this paper. ASTM International does not endorse any products represented in this paper.