Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Effect of substrate surface roughness on wetting behaviour of vegetable oils(2009) Prabhu, K.N.; Fernades, P.; Kumar, G.Vegetable oils are mainly used in the heat treating industry due to their environmental friendliness. In the present work the effect of surface roughness on spreading of vegetable oils on stainless steel substrates was investigated. Spreading phenomenon was digitally recorded and analyzed. All of the oils under investigation exhibited power law spreading behaviour of the type: A = ktn, where A, t, k and n represent the drop base contact area, spreading time, constant and exponent, respectively. The coconut and sunflower oils exhibited accelerated kinetics owing to their lower viscosity as compared to palm and mineral oils while peanut oil showed intermediate behaviour. Viscous regime was dominant during spreading of mineral and palm oils as compared to that of coconut oil. All the oils took longer period of time on rough surfaces than on smooth surfaces to relax to the same degree of wetting. Oils spreading on rough surfaces had to overcome the additional barrier due to asperities of the rough surface. Contact angle decreased with increase in roughness supporting the Wenzel's proposition. The decrease was significant for increase in roughness from 0.25 ?m to 0.50 ?m for all oils. However, the effect was negligible with further increase in roughness particularly for high viscosity oils. A spread parameter (?) is proposed to account for the variation of contact angle with surface roughness of the substrate and momentum diffusivity of the spreading liquid. The result suggested that low viscosity liquids exhibit improved wetting characteristics during spreading on rough surfaces. A model is proposed to estimate dynamic contact angles on substrates having varying surface roughness. © 2008 Elsevier Ltd. All rights reserved.Item Wetting behaviour and evolution of microstructure of Sn-Ag-Zn solders on copper substrates with different surface textures(2010) Satyanarayan, S.; Prabhu, K.N.The effect of surface roughness on wetting behaviour and evolution of microstructure of two lead-free solders (Sn-2.625Ag-2.25Zn and Sn-1.75Ag-4.5Zn) on copper substrate was investigated. Both solders exhibited good wettability on copper substrates having rough surface and lower wettabilty on smooth surfaces. The contact angles of solders decreased linearly with increase in surface roughness of the substrate. The exponential power law, ?=exp(-K ?n), was used to model the relaxation behaviour of solders. A high intermetallic growth was observed at the interface particularly on copper substrates with rough surface texture. A thin continuous interface showing scallop intermetallic compounds (IMC) was obtained on smooth surfaces. With an increase in surface roughness, the IMC morphology changed from scallop shaped to needle type at the Sn-2.625Ag-2.25Zn solder/substrate interface and nodular to plate like IMCs for Sn-1.75Ag-4.5Zn solder matrix. Copyright © 2010 by ASTM International.Item Effect of Bath Temperature on Cooling Performance of Molten Eutectic NaNO3-KNO3 Quench Medium for Martempering of Steels(Springer Boston, 2017) Pranesh Rao, K.M.; Prabhu, K.N.Martempering is an industrial heat treatment process that requires a quench bath that can operate without undergoing degradation in the temperature range of 423 K to 873 K (150 °C to 600 °C). The quench bath is expected to cool the steel part from the austenizing temperature to quench bath temperature rapidly and uniformly. Molten eutectic NaNO3-KNO3 mixture has been widely used in industry to martemper steel parts. In the present work, the effect of quench bath temperature on the cooling performance of a molten eutectic NaNO3-KNO3 mixture has been studied. An Inconel ASTM D-6200 probe was heated to 1133 K (860 °C) and subsequently quenched in the quench bath maintained at different temperatures. Spatially dependent transient heat flux at the metal–quenchant interface for each bath temperature was calculated using inverse heat conduction technique. Heat transfer occurred only in two stages, namely, nucleate boiling and convective cooling. The mean peak heat flux (qmax) decreased with increase in quench bath temperature, whereas the mean surface temperature corresponding to qmax and mean surface temperature at the start of convective cooling stage increased with increase in quench bath temperature. The variation in normalized cooling parameter t85 along the length of the probe increased with increase in quench bath temperature. © 2017, The Minerals, Metals & Materials Society and ASM International.Item A Comparative Study on Cooling Performance of Hot Oil and Molten Salt Quench Media for Industrial Heat Treatment(Springer, 2020) Pranesh Rao, K.M.; Prabhu, K.N.The present work presents a comprehensive comparative study on the cooling performance of hot oil and molten 54%KNO3-7%NaNO3-39%NaNO2 eutectic mixture quench media. The study was conducted using a cylindrical Inconel probe of 12.5 mm diameter and 60 mm length. Cooling curves at different locations in the probe were acquired and were subsequently used to calculate spatially dependent transient heat flux at the metal/quenchant interface. The heat extraction mechanism in hot oil and NaNO2 eutectic mixture was found to be different. Heat transfer occurred in two stages, namely boiling stage and convective cooling stage during quenching in molten NaNO2 eutectic mixture. In the case of hot oil, apart from these two stages, third stage of cooling, namely vapor blanket stage, was observed. A detailed study was conducted to compare the magnitude and uniformity of heat extraction during each stage of quenching. Molten salt offered a higher cooling rate and more spatial uniform cooling as compared to that obtained in hot oil quench medium. The non-uniformity in surface temperature during boiling stage in Inconel probe was ten times lower in molten salt medium as compared to that observed in the hot oil medium. However, the non-uniformity in surface temperature during convective cooling stage in both the media were comparable. Based on the distribution of characteristic cooling time (t85) calculated in quenched Inconel probe, higher and uniform hardness distribution is predicted in steel parts quenched in molten NaNO2 eutectic mixture media as compared to that in hot oil. © 2020, ASM International.