Faculty Publications

Search Results

Now showing 1 - 4 of 4

Modification of eutectic silicon in Al-Si alloys
(2008) Hegde, S.; Prabhu, K.N.
The mechanical properties of Al-Si alloys are strongly related to the size, shape and distribution of eutectic silicon present in the microstructure In order to improve mechanical properties, these alloys are generally subjected to modification melt treatment, which transforms the acicular silicon morphology to fibrous one resulting in a noticeable improvement in elongation and strength. Improper melt treatment procedures, fading and poisoning of modifiers often result in the structure which is far from the desired one. Hence it is essential to assess the effectiveness of melt treatment before pouring. A much investigated reliable thermal analysis technique is generally used for this purpose. The deviation from the standard curve in thermal analysis helps in assessing the level of refinement of the Si structure. In the present review an attempt is made to discuss various aspects of modification, including mechanism, interaction of defects and non-destructive assessment by thermal analysis. © 2008 Springer Science+Business Media, LLC.
Heat transfer during solidification of chemically modified Al-Si alloys around a copper chill
(2011) Prabhu, K.N.; Hegde, S.
The solidifying metal/chill contour will significantly affect the boundary heat transfer coefficients, and solidification modellers should be aware of the casting conditions for which the heat transfer coefficients are determined. The previous work carried out on solidification of Al-Si alloys in a metallic mould and solidification against bottom/top chills has shown that modification and chilling have synergetic effect resulting in a significant increase in the heat flux transients at the casting/chill interface. In the present work, the heat transfer during solidification of unmodified and chemically modified Al-Si alloys around a cylindrical copper chill was investigated. Heat flux transients were estimated using lumped heat capacitance method. Lower peak heat flux was obtained with chemically modified alloy. This is in contrast to the results reported for alloys solidifying against chills and in metallic moulds. The chill thermal behaviour and heat transfer to the chill material when surrounded by modified and unmodified alloys were explained on the basis of the decrease in the degree of undercooling in the case of modified alloy as compared to unmodified alloy and the change in contact condition and shrinkage characteristics of the alloy due to the addition of chemical modifiers. © 2011 Institute of Materials, Minerals and Mining.
Effect of chemical modification of Al-Si alloys on thermal diffusivity and contact heat transfer at the casting-chill interface
(2012) Prabhu, K.N.; Jayananda; Hegde, S.
The heat flow during the unidirectional downward solidification of Al-7Si and Al-12Si alloys was analyzed using thermal analysis technique and inverse modeling. Chills instrumented with thermocouples were brought into contact with a small pool of liquid metal so as to minimize the effect of convection caused by pouring and temperature gradients. Modification melt treatment resulted in an increase in the cooling rate of the solidifying casting near the casting-chill interfacial region. The corresponding interfacial heat flux transients were also found to be higher. The thermal diffusivities of alloys were measured using a laser pulse technique and were found to be higher for modified alloys. However, the increase in the heat flux transients was attributed mainly to the improvement in the casting-chill interfacial thermal contact condition brought about by the decrease in the surface tension of the liquid metal upon the addition of sodium. Copyright © 2012 by ASTM International.
The effect of simultaneous refinement and modification by cerium on microstructure and mechanical properties of Al-8% Si alloy
(Taylor and Francis Ltd. maney@maney.co.uk, 2016) Vijayan, V.; Prabhu, K.N.
The effect of cerium melt treatment on microstructure and mechanical properties of gravity die cast Al-8% Si alloy was studied. The addition of Ce transformed the large columnar ?-Al grains into fine equiaxed grains and modified the acicular eutectic Si into fine fibrous form. The addition of Ce resulted in the formation of needle-shaped complex Ce intermetallic along the grain boundaries. Electrical conductivity measurements are used for the first time to reveal the effect of Ce addition on modification of the eutectic Si. The electrical conductivity of the alloy increased with Ce melt treatment. Scanning Electron Microscopy results suggests that the Ce particles did not heterogeneously nucleate the ?-Al grains, instead the fine equiaxed grains were formed through an invariant reaction between the liquid melt and Ce phase. The ultimate tensile strength, % elongation and hardness of the alloy significantly improved due to simultaneous modification and refinement. © 2016 Informa UK Limited, trading as Taylor & Francis Group.

Faculty Publications

Browse

Filters

Settings

Sort By

Results per page

Search Results