Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Prabhu, K.N.Subject: search.filters.subject.Quenching

Search Results

Now showing 1 - 10 of 24
  • No Thumbnail Available
    Item
    Inverse modeling of heat transfer with application to solidification and quenching
    (2002) Prabhu, K.N.; Ashish, A.A.
    The inverse modeling of heat transfer involves the estimation of boundary conditions from the knowledge of thermal history inside a heat conducting body. Inverse analysis is extremely useful in modeling of contact heat transfer at interfaces of engineering surface during materials processing. In the present work, the one-dimensional transient heat conduction equation was inversely modeled in both cartesian as well as cylindrical coordinates. The model is capable of estimating heat flux transients, chill surface temperature, and total heat flow from the source to the sink for an input of thermal history inside the sink. The methodology was adopted to solve boundary heat transfer problems inversely during solidification and quenching. The response of the inverse solution to measured sensor data was studied by carrying out numerical experiments involving the use of varying grid size and time steps, future temperatures, and regularization techniques.
  • No Thumbnail Available
    Item
    Severity of quenching and kinetics of wetting of nanofluids and vegetable oils
    (ASTM International, 2010) Jagannath, V.; Prabhu, K.N.
    In the present work, the suitability of vegetable oil blends with mineral oil and alumina based nanofluids as quench media for industrial heat treatment was investigated. Sunflower oil, palm oil, and mineral oil were used for preparing the blends. Alumina based nanofluids of varying concentrations ranging from 0.01-4 % were used. The size of alumina particles was about 50 nm. The severity of quenching and heat transfer coefficients were estimated during quenching of copper probes. Heat transfer coefficients were estimated using a lumped heat capacitance model. The static contact angle was measured on copper substrates having a surface texture similar to the probes used for estimation of heat transfer coefficients. A dynamic contact angle analyzer was used for this purpose. The measured contact angles of nanofluids on copper were high compared to oils, indicating poor wetting by quench media that are polar in nature. Wetting characteristics had a significant effect on heat transfer coefficients estimated during quenching. Copyright © 2009 by ASTM International.
  • No Thumbnail Available
    Item
    Estimation of Heat Flux Transient During Quench Hardening of Varying Diameter Steel Probes Using IHCP-Phase Transformation Coupled Model
    (ASM International, 2023) Samuel, A.; Nayak, U.V.; Pranesh Rao, K.M.P.; Prabhu, K.N.
    The phase transformation model is coupled with the inverse heat conduction problem (IHCP) to estimate the steel/quenchant interfacial heat flux. Cylindrical steel probes having section thicknesses 25 and 50mm, respectively, and lengths 30mm were made from medium and high carbon steels (AISI 1045 and 52100). The probes were quenched in mineral, neem, and sunflower oils. The cooling curves at the centre and near the surface of steel probes were recorded. The near-surface cooling curve was used as a reference temperature data in the IHCP algorithm for the estimation of surface heat flux, whereas the cooling curve at the centre was used as the boundary condition of the axisymmetric model of the probe. The effect of phase transformation on the metal/quenchant interfacial heat flux was indicated by a kink and rise of heat flux. The increase in the section thickness of the probe from 25 to 50mm decreased the magnitude of the heat flux. Increasing section thickness increases the phase transformation, increasing the resistance to heat flow at the metal/quenchant interface. © © 2023 ASM International®
  • No Thumbnail Available
    Item
    Effect of surface roughness on metal/quenchant interfacial heat transfer and evolution of microstructure
    (Elsevier Ltd, 2007) Prabhu, K.N.; Fernandes, P.
    In the present work, the effect of surface roughness on heat transfer rates in various quenchants was determined. The heat flux transients at the probe/quenchant interface were estimated by inverse modeling of heat conduction during end quenching of stainless steel probes with three different surface roughness (grooved, Ra = 3.0 and 1 ?m). Heat transfer during quenching was correlated with the hardness obtained for medium carbon AISI 1060 steel specimens. The effect of surface roughness on heat transfer rate during quenching in water and brine was significant for rough surface whereas its effect on heat transfer rate is only marginal in high viscosity oil quenchants. A fully martensitic structure was observed with grooved surface subjected to water quenching. With a smooth surface a mixed microstructure was obtained. The oil quenched specimens were found to be less sensitive to surface roughness. © 2005 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    Item
    Effect of section size and agitation on heat transfer during quenching of AISI 1040 steel
    (2007) Fernandes, P.; Prabhu, K.N.
    In the present work an attempt has been made to determine the heat flux transients during quenching of Ø28 mm × 56 mm height and Ø44 mm × 88 mm height AISI 1040 steel specimens during lateral quenching in brine, water, palm oil and mineral oil. The heat flux transients were estimated by inverse modeling of heat conduction. The variation of heat flux transients with surface temperature for different quenching media is investigated. Higher peak heat flux transients are obtained for 28 mm diameter specimen than 44 mm diameter specimen during quenching in aqueous media. However quenching with oil media shows opposite results. Agitation of quenching medium increases the peak heat flux during the quenching of steel specimen in all the quenching media. Peak hardness is obtained at the surface and with smaller diameter specimens during agitation. © 2006 Elsevier B.V. All rights reserved.
  • No Thumbnail Available
    Item
    Nanoquenchants for industrial heat treatment
    (2008) Prabhu, K.N.; Fernades, P.
    The present work outlines the possibility of using nanofluids for industrial heat treatment. Development of nanoquenchants having (i) high quench severity for enhancement of heat transfer for thick sections with low quench sensitivity and (ii) low cooling severity for thin sections with high quench sensitivity would be extremely useful to the heat treating community. The temperature dependent heat transfer coefficient and the wettability of the medium are the two important parameters that can be used to characterize a nanoquenchant to assess its suitability for industrial heat treatment. © 2007 ASM International.
  • No Thumbnail Available
    Item
    Severity of quenching and kinetics of wetting of nanofluids and vegetable oils
    (2009) Jagannath, V.; Prabhu, K.N.
    In the present work, the suitability of vegetable oil blends with mineral oil and alumina based nanofluids as quench media for industrial heat treatment was investigated. Sunflower oil, palm oil, and mineral oil were used for preparing the blends. Alumina based nanofluids of varying concentrations ranging from 0.01-4 % were used. The size of alumina particles was about 50 nm. The severity of quenching and heat transfer coefficients were estimated during quenching of copper probes. Heat transfer coefficients were estimated using a lumped heat capacitance model. The static contact angle was measured on copper substrates having a surface texture similar to the probes used for estimation of heat transfer coefficients. A dynamic contact angle analyzer was used for this purpose. The measured contact angles of nanofluids on copper were high compared to oils, indicating poor wetting by quench media that are polar in nature. Wetting characteristics had a significant effect on heat transfer coefficients estimated during quenching. Copyright © 2009 by ASTM International.
  • No Thumbnail Available
    Item
    Comparison of Grossmann and lumped heat capacitance methods for assessment of heat transfer characteristics of quench media
    (2011) Prabhu, K.N.; Ali, I.
    The suitability of Grossmann and lumped heat capacitance (LHC) methods for estimation of quench severity of nanofluids, brine solutions and a laboratory detergent based medium was investigated. The study involved the assessment of the effect of section thickness of the probe on heat transfer coefficients for different quench media. Computer aided cooling curve analysis during quenching of type 304 stainless steel probes was carried out. The measured thermal history data were used to estimate heat transfer coefficients by Grossmann and LHC methods. The LHC method based on a 10 mm diameter stainless steel probe was found to be applicable for characterising media having quench severity less than 20 m-1. Although Grossmann method is based on the concept of average heat transfer coefficient, it can be used for quench media having varying severity of quenching. Grossmann method is found to be more sensitive to the effect of section thickness on heat transfer. © 2011 IHTSE Partnership.
  • No Thumbnail Available
    Item
    Characterisation of water base copper nanoquenchants by standard cooling curve analysis
    (2011) Ramesh, G.; Prabhu, K.N.
    Water base copper nanofluids having concentrations varying from 0?001 to 0?1 vol.-% were prepared and used as quench media for immersion quenching. Cooling curve analyses were carried out by using a standard ISO/DIS 9950 quench probe. An inverse heat conduction model is employed to estimate the metal/nanoquenchant interfacial heat flux transients from the measured temperature field and thermophysical properties of the quench probe material. The addition of copper nanoparticles had a significant effect on the occurrence of the vapour blanket stage and nucleate boiling stage. Furthermore, all six cooling curve parameters were found to be altered by adding nanoparticles to water. The contact angle of water decreased from 67 to 39° by adding 0?1 vol.-% of copper nanoparticles indicating the improved wettability of nanofluids. The heat flux curve shows a maximum initially then drops rapidly during quenching. The peak cooling rate and heat flux of water increased by adding copper nanoparticles up to 0?01 vol.-%. Both parameters decreased with further increase in concentration of nanoparticles. The results suggest that the quench severity of water could be altered by adding copper nanoparticles. © 2011 IHTSE Partnership.
  • No Thumbnail Available
    Item
    Effect of addition of aluminum nanoparticles on cooling performance and quench severity of water during immersion quenching
    (ASTM International, 2012) Ramesh, G.; Prabhu, K.N.
    In the present work, the effect of the addition of aluminum nanoparticles in concentrations varying from 0.001 to 0.5 vol. % on the cooling performance and quench severity of water during immersion quenching is investigated. The results of cooling curve analyses show that an increase in nanoparticle concentration increased the cooling rates at critical temperatures up to 0.05 vol. % and decreased them thereafter. The transition from the vapor blanket stage to the nucleate boiling stage was also altered by quenching in nanofluids. A finite difference heat transfer program was employed to generate cooling curves at different values of heat transfer coefficient from thermo-physical properties of the quench probe material. A Grossmann H quench severity versus cooling rate curve was established, and from this curve, the H factors of prepared nanofluids were estimated. An increase in nanoparticle concentration up to 0.05 vol. % resulted in an increase of the H value of water from 63 m -1 to 93 m-1, and any further increase in the concentration of nanoparticles resulted in a decrease in H. The results suggest both the enhancement and the deterioration of the cooling performance of water by the addition of aluminum nanoparticles. Copyright © 2012 by ASTM International.