Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
9 results
Search Results
Item Severity of quenching and kinetics of wetting of nanofluids and vegetable oils(ASTM International, 2010) Jagannath, V.; Prabhu, K.N.In the present work, the suitability of vegetable oil blends with mineral oil and alumina based nanofluids as quench media for industrial heat treatment was investigated. Sunflower oil, palm oil, and mineral oil were used for preparing the blends. Alumina based nanofluids of varying concentrations ranging from 0.01-4 % were used. The size of alumina particles was about 50 nm. The severity of quenching and heat transfer coefficients were estimated during quenching of copper probes. Heat transfer coefficients were estimated using a lumped heat capacitance model. The static contact angle was measured on copper substrates having a surface texture similar to the probes used for estimation of heat transfer coefficients. A dynamic contact angle analyzer was used for this purpose. The measured contact angles of nanofluids on copper were high compared to oils, indicating poor wetting by quench media that are polar in nature. Wetting characteristics had a significant effect on heat transfer coefficients estimated during quenching. Copyright © 2009 by ASTM International.Item Replacement of heat sink fan by nanocoolants for enhancement of CPU efficiency(Institution of Engineering and Technology journals@theiet.org, 2013) Siddique, A.B.; Prabhu, K.N.The highest temperature under which a CPU can operate without interruption is 90°C. Heat sink fans generally provided for removal of heat produced by the processor are proved to be inadequate when CPU usage is 100%. The objective of this work is to exploit the enhanced thermal properties of nanofluid for dissipation of heat from the Intel (R) Core (TM) i5- 2310 CPU @ 2.9GHz quad-core processor for cooling it to a suitable operating temperature. Nanocoolants were prepared with two types of nanoparticles, titania and copper. The volume percentage of nanoparticles in nanocoolants were 0.01 and 0.1. It was observed that nanofluids are more efficient coolants than the base fluid and found to be significantly better than the traditional heat sink fan, as indicated by the CPU temperature, under the same loading condition. The average CPU temperatures were 90°C, 58°C, 56.6°C and 54.5°C with heat sink fan, deionized water, 0.1 vol% TiO2 and 0.1 vol% Cu nanofluids respectively at the flow rate of 700ml/min and CPU usage of 100%. The lowest CPU operating temperature (54.5°C) was obtained with 0.1 vol% Cu at the flow rate of 700ml/min. The cooling of CPU was also affected by the flow rate and the volume fraction of nanoparticles in the nanocoolant.Item Severity of quenching and kinetics of wetting of nanofluids and vegetable oils(2009) Jagannath, V.; Prabhu, K.N.In the present work, the suitability of vegetable oil blends with mineral oil and alumina based nanofluids as quench media for industrial heat treatment was investigated. Sunflower oil, palm oil, and mineral oil were used for preparing the blends. Alumina based nanofluids of varying concentrations ranging from 0.01-4 % were used. The size of alumina particles was about 50 nm. The severity of quenching and heat transfer coefficients were estimated during quenching of copper probes. Heat transfer coefficients were estimated using a lumped heat capacitance model. The static contact angle was measured on copper substrates having a surface texture similar to the probes used for estimation of heat transfer coefficients. A dynamic contact angle analyzer was used for this purpose. The measured contact angles of nanofluids on copper were high compared to oils, indicating poor wetting by quench media that are polar in nature. Wetting characteristics had a significant effect on heat transfer coefficients estimated during quenching. Copyright © 2009 by ASTM International.Item Enhancement of heat transfer characteristics of transformer oil by addition of aluminium nanoparticles(2011) Rajesh, E.; Prabhu, K.N.A two step approach involving the synthesis of Al nanoparticles by mechanical milling followed by dispersion of the nanoparticles in the base fluid is adopted in the present work to prepare transformer oil based nanofluids. Stainless steel (AISI 304) probes of diameter 15 mm and height 70 mm were used to determine the cooling rate intensities of nanofluids. Heat transfer coefficients were determined using Kobasko's method. A dynamic contact angle analyzer was used to determine the contact angle of the droplet on the substrate. The addition of Al nanoparticles to the base fluid decreases the wettability and improves its heat transfer capability. The vapour phase stage existed for a longer period of time for transformer oil than for Al-transformer oil based nanofluids. The dispersion of nanoparticles in the base fluid is believed to disrupt the vapour blanket stage in the early stage of the cooling process. The peak heat transfer coefficient increases with an increase in the Al nanoparticle content in the oil. The addition of 0.5 vol % nanoparticles enhances the peak heat transfer coefficient by about 70 %. Copyright © 2011 by ASTM International.Item Comparison of Grossmann and lumped heat capacitance methods for assessment of heat transfer characteristics of quench media(2011) Prabhu, K.N.; Ali, I.The suitability of Grossmann and lumped heat capacitance (LHC) methods for estimation of quench severity of nanofluids, brine solutions and a laboratory detergent based medium was investigated. The study involved the assessment of the effect of section thickness of the probe on heat transfer coefficients for different quench media. Computer aided cooling curve analysis during quenching of type 304 stainless steel probes was carried out. The measured thermal history data were used to estimate heat transfer coefficients by Grossmann and LHC methods. The LHC method based on a 10 mm diameter stainless steel probe was found to be applicable for characterising media having quench severity less than 20 m-1. Although Grossmann method is based on the concept of average heat transfer coefficient, it can be used for quench media having varying severity of quenching. Grossmann method is found to be more sensitive to the effect of section thickness on heat transfer. © 2011 IHTSE Partnership.Item Characterisation of water base copper nanoquenchants by standard cooling curve analysis(2011) Ramesh, G.; Prabhu, K.N.Water base copper nanofluids having concentrations varying from 0?001 to 0?1 vol.-% were prepared and used as quench media for immersion quenching. Cooling curve analyses were carried out by using a standard ISO/DIS 9950 quench probe. An inverse heat conduction model is employed to estimate the metal/nanoquenchant interfacial heat flux transients from the measured temperature field and thermophysical properties of the quench probe material. The addition of copper nanoparticles had a significant effect on the occurrence of the vapour blanket stage and nucleate boiling stage. Furthermore, all six cooling curve parameters were found to be altered by adding nanoparticles to water. The contact angle of water decreased from 67 to 39° by adding 0?1 vol.-% of copper nanoparticles indicating the improved wettability of nanofluids. The heat flux curve shows a maximum initially then drops rapidly during quenching. The peak cooling rate and heat flux of water increased by adding copper nanoparticles up to 0?01 vol.-%. Both parameters decreased with further increase in concentration of nanoparticles. The results suggest that the quench severity of water could be altered by adding copper nanoparticles. © 2011 IHTSE Partnership.Item Effect of addition of aluminum nanoparticles on cooling performance and quench severity of water during immersion quenching(2012) Ramesh, G.; Prabhu, K.N.In the present work, the effect of the addition of aluminum nanoparticles in concentrations varying from 0.001 to 0.5 vol. % on the cooling performance and quench severity of water during immersion quenching is investigated. The results of cooling curve analyses show that an increase in nanoparticle concentration increased the cooling rates at critical temperatures up to 0.05 vol. % and decreased them thereafter. The transition from the vapor blanket stage to the nucleate boiling stage was also altered by quenching in nanofluids. A finite difference heat transfer program was employed to generate cooling curves at different values of heat transfer coefficient from thermo-physical properties of the quench probe material. A Grossmann H quench severity versus cooling rate curve was established, and from this curve, the H factors of prepared nanofluids were estimated. An increase in nanoparticle concentration up to 0.05 vol. %resulted in an increase of the H value of water from 63 m 1 to 93 m 1, and any further increase in the concentration of nanoparticles resulted in a decrease in H. The results suggest both the enhancement and the deterioration of the cooling performance of water by the addition of aluminum nanoparticles. Copyright © 2012 by ASTM International.Item Wetting Behavior and Heat Transfer of Aqueous Graphene Nanofluids(Springer New York LLC barbara.b.bertram@gsk.com, 2016) Nayak, U.V.; Prabhu, K.N.Aqueous graphene nanofluids having concentrations 0.01, 0.1, and 0.3 vol.% were used as heat transfer media during quenching of ISO 9950 inconel alloy probe. Contact angle measurements were carried out to assess the wettability of graphene nanofluids. Nanofluids showed better wettability compared to base water with over 16% reduction in their contact angles. The cooling performance of the quench media was assessed by cooling curve analysis during quenching of an instrumented inconel probe from 860 °C into the quench medium. Recorded temperature readings showed longer vapor phase stage during quenching with nanofluids. The severity of nanofluids was found to be lower relative to water. During quenching with nanofluids, the estimated spatiotemporal heat flux transients at the metal/quenchant interface showed that more heat was removed during the vapor phase stage of cooling. The present study brings out the possibility of using stable water-graphene nanoplatelet suspensions for quench heat treatment of steel components requiring cooling severity between water and oil/polymer quenchants. © 2016, ASM International.Item Assessment of spatiotemporal heat flux during quenching in TiO2 and AlN nanofluids(ASTM International, 2017) Nayak, U.V.; Ramesh, G.; Prabhu, K.N.In the present work, spatiotemporal heat flux transients were estimated during quenching of an Inconel 600 alloy probe in water-based titanium dioxide (TiO2) and aluminum nitride (AlN) nanofluids that have nanoparticle concentrations varying from 0.001 to 0.5 vol. %. The results showed reduced peak heat flux and a longer vapor phase stage during quenching with nanofluids compared to quenching with water. The peak heat flux for quenching in nanofluids was lowered with increase in the nanoparticle concentration. Quenching with TiO2 nanofluids resulted in slower heat extraction compared to quenching in AlN nanofluids at higher concentrations. Quenching with nanofluids resulted in a more uniform quench compared to quenching with water because of the reduction in the rewetting period. © © 2017 by ASTM International.