Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Wetting kinetics, kinematics and heat transfer characteristics of pongamia pinnata vegetable oil for industrial heat treatment(Elsevier Ltd, 2014) Ramesh, G.; Prabhu, K.The suitability of pongamia pinnata vegetable oil as cooling medium for quench heat treatment was investigated. Wetting kinetics, kinematics and heat transfer characteristics of pongamia oil during immersion quenching of hot Inconel probe were determined and compared with palm and mineral oils. A comparison of the relaxation of contact angle indicated early attainment of equilibrium contact angle for pongamia oil droplet on Inconel substrate. The equilibrium contact angle value of pongamia oil was in between mineral and palm oils. However, the spreading kinetics was faster with pongamia oil. Pongamia oil showed the formation of a stable vapour film on the probe surface during quenching. This phenomenon was not observed in palm oil and other vegetable oils reported in literature. Pongamia pinnata oil exhibits uniform nature of wetting front, intermediate rewetting temperature and less variations in rewetting temperatures during quenching. The hardening power of pongamia oil was higher than palm and mineral oils and the cooling of the probe was more uniform during quenching in pongamia oil. The heat transfer characteristics of pongamia oil were found to be superior to palm and mineral oils after film/transition boiling. Pongamia oil showed lower heat transfer but more uniform cooling during film boiling. © 2014 Elsevier B.V.Item Wetting and cooling performance of mineral oils for quench heat treatment of steels(Iron and Steel Institute of Japan, 2014) Ramesh, G.; Prabhu, K.In the present work, wetting kinetics, kinematics and heat transfer characteristics of mineral oils having varying thermo-physical properties sourced from different suppliers were investigated using contact angle, online video imaging and cooling curve analysis techniques. The relaxation behavior of mineral oils of low viscosity and surface tension on Inconel substrate indicated improved wettability and fast spreading kinetics while mineral oils of high viscosity and surface tension showed reduced wettability and slower spreading kinetics. Further, the spreading behavior of mineral oils of lower viscosity and density showed the absence of viscous regime. During rewetting, formation of double wetting fronts and more uniform nature of wetting front were observed with mineral oils of high viscosity and flash point whereas no additional wetting front was observed for mineral oils of low viscosity and flash point. Among the convectional/fast/hot mineral oils, higher wetting front velocity and cooling rate were obtained for low viscosity mineral oil. The heat extracting capability of high viscosity mineral oils was higher during vapour and nucleate boiling and lower during liquid cooling stage. Further, highly viscous mineral oils showed uniform heat transfer compared to mineral oils having low viscosity. © 2014 ISIJ.Item Spatial dependence of heat flux transients and wetting behavior during immersion quenching of inconel 600 probe in brine and polymer media(Springer Boston, 2014) Ramesh, G.; Prabhu, K.Cooling curve analysis of Inconel 600 probe during immersion quenching in brine and polymer quench media was carried out. Thermal histories at various axial and radial locations were recorded using a high-speed data acquisition system and were input to an inverse heat-conduction model for estimating the metal/quenchant heat flux transients. A high performance smart camera was used for online video imaging of the immersion quenching process. Solution to two-dimensional inverse heat-conduction problem clearly brings out the spatial dependence of boundary heat flux transients for a Inconel 600 probe with a simple cylindrical geometry. The estimated heat flux transients show large variation on axial as well as radial directions of quench probe surface for brine quenching. Polymer quenching showed less variation in metal/quenchant heat flux transients. Shorter durations of vapor film, higher rewetting temperatures, and faster movement of wetting front on quench probe surface were observed with brine quenching. Measurement of dynamic contact angle showed better spreading and good wettability for polymer medium as compared to brine quenchant. The solid-liquid interfacial tension between polymer medium and Inconel substrate was lower compared with that of solution. Rewetting and boiling processes were nonuniform and faster on quench probe surface during immersion quenching in brine solution. For the polymer quench medium, slow rewetting, uniform boiling and repeated wetting were observed. © 2014 The Minerals, Metals & Materials Society and ASM International.Item Comparative study of wetting and cooling performance of polymer-salt hybrid quench medium with conventional quench media(Taylor and Francis Ltd., 2015) Ramesh, G.; Prabhu, K.Wetting kinetics, kinematics, and cooling performance of a polymer-salt hybrid quenchant were investigated. The rewetting phenomenon for brine, water, polymer, and polymer-salt hybrid solutions was characterized as rapid uniform, fast non-uniform, slow uniform, and fast uniform processes, respectively. A dimensionless rewetting time was proposed to assess the nature of the wetting front. The hybrid quenchant showed higher heat transfer during vapor and transition boiling and lower heat transfer during nucleate boiling and convective cooling. The presence of salt in the hybrid solution resulted in early destabilization of the vapor film and an increase in wetting front velocity and rewetting temperature. The polymer constituent delayed the rewetting phenomenon. © 2015 Taylor & Francis Group, LLC.Item Heat transfer and quench performance of aqueous CuO nanofluids during immersion quenching(Inderscience Publishers, 2016) Nayak, U.; Prabhu, K.The present work involves the assessment of quench performance of aqueous-copper oxide nanofluids. Distilled water-based copper oxide nanofluids of concentrations 0.01, 0.05, 0.1 and 1.0 vol.% were prepared by a two-step process. Cooling curves analysis was carried out using an inconel probe that was instrumented with thermocouples. The recorded temperature data during experiments was used to estimate spatiotemporal heat flux transients by solving inverse heat conduction problem. Quenching of probe in nanofluids resulted in longer vapour phase stage duration compared to distilled water. The addition of nanoparticles altered the peak flux and the time of its occurrence. Rewetting temperatures were found to be lower for nanofluids. The measured thermal conductivities and viscosities showed similar values for all quench media. © 2016 Inderscience Enterprises Ltd.