Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Heat flow at the casting/mold interface was assessed and studied during solidification of Al-Cu-Si (LM 21) alloy in preheated cast iron molds of two different thicknesses, coated with graphite and alumina based dressings. The casting and the mold were instrumented with thermocouples connected to a computer controlled temperature data acquisition system. The thermal history at nodal locations in the mold and casting obtained during experimentation was used to estimate the heat flux by solving the one-dimensional inverse heat conduction problem. The cooling rate and solidification time were measured using the computer-aided cooling curve analysis data. The estimated heat flux transients showed a peak due to the formation of a stable solid shell, which has a higher thermal conductivity compared with the liquid metal in contact with the mold wall prior to the occurrence of the peak. The high values of heat flux transients obtained with thin molds were attributed to mold distortion due to thermal stresses. For thin molds, assumption of Newtonian heating yielded reliable interfacial heat transfer coefficients as compared with one-dimensional inverse modeling. The time of occurrence of peak heat flux increased with a decrease in the mold wall thickness and increase in the casting thickness. © ASM International.(Casting/mold thermal contact heat transfer during solidification of Al-Cu-Si alloy (LM 21) plates in thick and thin molds) Prabhu, K.; Chowdary, B.; Venkataraman, N.2005Item Spatial dependence of heat flux transients and wetting behavior during immersion quenching of inconel 600 probe in brine and polymer media(Springer Boston, 2014) Ramesh, G.; Prabhu, K.Cooling curve analysis of Inconel 600 probe during immersion quenching in brine and polymer quench media was carried out. Thermal histories at various axial and radial locations were recorded using a high-speed data acquisition system and were input to an inverse heat-conduction model for estimating the metal/quenchant heat flux transients. A high performance smart camera was used for online video imaging of the immersion quenching process. Solution to two-dimensional inverse heat-conduction problem clearly brings out the spatial dependence of boundary heat flux transients for a Inconel 600 probe with a simple cylindrical geometry. The estimated heat flux transients show large variation on axial as well as radial directions of quench probe surface for brine quenching. Polymer quenching showed less variation in metal/quenchant heat flux transients. Shorter durations of vapor film, higher rewetting temperatures, and faster movement of wetting front on quench probe surface were observed with brine quenching. Measurement of dynamic contact angle showed better spreading and good wettability for polymer medium as compared to brine quenchant. The solid-liquid interfacial tension between polymer medium and Inconel substrate was lower compared with that of solution. Rewetting and boiling processes were nonuniform and faster on quench probe surface during immersion quenching in brine solution. For the polymer quench medium, slow rewetting, uniform boiling and repeated wetting were observed. © 2014 The Minerals, Metals & Materials Society and ASM International.Item Heat transfer and quench performance of aqueous CuO nanofluids during immersion quenching(Inderscience Publishers, 2016) Nayak, U.; Prabhu, K.The present work involves the assessment of quench performance of aqueous-copper oxide nanofluids. Distilled water-based copper oxide nanofluids of concentrations 0.01, 0.05, 0.1 and 1.0 vol.% were prepared by a two-step process. Cooling curves analysis was carried out using an inconel probe that was instrumented with thermocouples. The recorded temperature data during experiments was used to estimate spatiotemporal heat flux transients by solving inverse heat conduction problem. Quenching of probe in nanofluids resulted in longer vapour phase stage duration compared to distilled water. The addition of nanoparticles altered the peak flux and the time of its occurrence. Rewetting temperatures were found to be lower for nanofluids. The measured thermal conductivities and viscosities showed similar values for all quench media. © 2016 Inderscience Enterprises Ltd.Item Experimental investigation of heat transfer characteristics of polyethylene glycol (PEG) based quench media for industrial heat treatment(Elsevier Inc., 2023) Soni, A.; Samuel, A.; Prabhu, K.Aqueous polymer quenchants are now increasingly used in the quench hardening of steels. The inverse solubility property of polymer media leads to polymer film encapsulation of the quenched component, followed by an instantaneous rupture of the polymer film. The film boiling stage is absent, thus improving heat transfer uniformity. In the present investigation, the effect of molecular weight of Polyethylene glycol (PEG) on heat transfer characteristics of PEG/water quenchants with concentrations of 5, 10, and 20 vol% was studied. The cooling curve analysis is performed to assess the cooling characteristics. Spatially dependent surface heat flux transients are estimated using the inverse heat conduction method. The rewetting kinematics is analyzed by videography and acoustic analysis of polymer film rupture during quenching. The results indicated that an increase in the molecular weight of PEG from 200 to 6000 changed the rewetting kinematics from a local wetting front movement to an instantaneous rupture of the polymer film. The change in the rewetting kinematics is reflected in the surface heat flux, indicating an increased uniformity of heat transfer. The film rupture acoustics showed that the polymer film's instantaneous breakup had a higher sound intensity than the one showing wetting front motion. © 2023 Elsevier Inc.