Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Dimensionless cooling performance parameter for characterization of quench media(2013) Ramesh, G.; Prabhu, K.The effect of varying thermal properties and boundary heat transfer coefficients on temperature profiles inside cylindrical quench probes was simulated during immersion cooling. The results of simulation indicated that, for assessment of the cooling performance of the quench media, the ratio of the quench probe diameter to its thermal conductivity should be less than 0.0005 m2K/W. A simple dimensionless cooling parameter (D 2CR/??T) was proposed to assess the cooling performance of quench media. © 2013 The Minerals, Metals & Materials Society and ASM International.Item Effect of thermal conductivity and viscosity on cooling performance of liquid quench media(Maney Publishing Suite 1C, Joseph's Well, Hanover Walk Leeds LS3 1AB, 2014) Ramesh, G.; Prabhu, K.In this present work, the effect of the thermophysical properties of quenchants on its cooling performance was investigated. Water, brine solutions, polymer solutions and mineral oils were chosen to have quench media with varying thermophysical properties. Cooling curve analyses were carried out by using standard ISO/DIS 9950 quench probe. Grossmann H quench severity of the quench media was determined from the relation of H and cooling rate. Cooling curve analysis results showed that the change in thermophysical properties of the quench media had significant effect on the cooling history of the quench probe. The viscosity of the quenchant used for immersion quenching is the most important factor that controls the cooling performance of the quenchant compared to thermal conductivity of the quench medium. © 2014 IHTSE Partnership.Item Wetting and cooling performance of mineral oils for quench heat treatment of steels(Iron and Steel Institute of Japan, 2014) Ramesh, G.; Prabhu, K.In the present work, wetting kinetics, kinematics and heat transfer characteristics of mineral oils having varying thermo-physical properties sourced from different suppliers were investigated using contact angle, online video imaging and cooling curve analysis techniques. The relaxation behavior of mineral oils of low viscosity and surface tension on Inconel substrate indicated improved wettability and fast spreading kinetics while mineral oils of high viscosity and surface tension showed reduced wettability and slower spreading kinetics. Further, the spreading behavior of mineral oils of lower viscosity and density showed the absence of viscous regime. During rewetting, formation of double wetting fronts and more uniform nature of wetting front were observed with mineral oils of high viscosity and flash point whereas no additional wetting front was observed for mineral oils of low viscosity and flash point. Among the convectional/fast/hot mineral oils, higher wetting front velocity and cooling rate were obtained for low viscosity mineral oil. The heat extracting capability of high viscosity mineral oils was higher during vapour and nucleate boiling and lower during liquid cooling stage. Further, highly viscous mineral oils showed uniform heat transfer compared to mineral oils having low viscosity. © 2014 ISIJ.Item A dimensional parameter for prediction of cooling performance of quenchants(ASTM International, 2014) Prabhu, K.; Ramesh, G.Computer aided cooling curve analysis was carried out during immersion quenching of ISO/DIS 9950 quench probe. Water, brine solutions, polymer solutions, mineral oils, and vegetable oils were used as quench media. The results showed that the quench medium used had a significant effect on the quench probe cooling curve parameters. An empirical correlation was proposed to predict the average cooling rate from surface tension, wetting angle, thermal conductivity, and kinematic viscosity of the quench medium. © 2014 by ASTM International.Item Cooling performance of select mineral oil and polymer quenchants(ASTM International, 2014) Tiwary, V.; Prabhu, K.In the present investigation, quench severity was determined for industrial oil quenchants and varying concentrations of PAG polymer. Viscosity, thermal conductivity, density, flash point, and fire point were measured for all quenchants. Cooling curve parameters were determined based on cooling curve analysis ISO/DIS 9950 technique. An Inconel 600 probe was used for this purpose. Severity of quenching was determined based on the Grossmann technique. Viscosity and thermal conductivity had a significant effect on quench severity. Heat flux and HTC at the metal/quenchant interface were computed by both lumped capacitance and Inverse modeling techniques. The effect of ultrasonic and Tensi agitation on cooling curve parameters was assessed. Polymer quenchants of lower concentrations showed marginally higher heat transfer rates compared to water particularly during unagitated condition. © © 2014 by ASTM International.Item Comparative study of wetting and cooling performance of polymer-salt hybrid quench medium with conventional quench media(Taylor and Francis Ltd., 2015) Ramesh, G.; Prabhu, K.Wetting kinetics, kinematics, and cooling performance of a polymer-salt hybrid quenchant were investigated. The rewetting phenomenon for brine, water, polymer, and polymer-salt hybrid solutions was characterized as rapid uniform, fast non-uniform, slow uniform, and fast uniform processes, respectively. A dimensionless rewetting time was proposed to assess the nature of the wetting front. The hybrid quenchant showed higher heat transfer during vapor and transition boiling and lower heat transfer during nucleate boiling and convective cooling. The presence of salt in the hybrid solution resulted in early destabilization of the vapor film and an increase in wetting front velocity and rewetting temperature. The polymer constituent delayed the rewetting phenomenon. © 2015 Taylor & Francis Group, LLC.Item Experimental investigation of heat transfer characteristics of polyethylene glycol (PEG) based quench media for industrial heat treatment(Elsevier Inc., 2023) Soni, A.; Samuel, A.; Prabhu, K.Aqueous polymer quenchants are now increasingly used in the quench hardening of steels. The inverse solubility property of polymer media leads to polymer film encapsulation of the quenched component, followed by an instantaneous rupture of the polymer film. The film boiling stage is absent, thus improving heat transfer uniformity. In the present investigation, the effect of molecular weight of Polyethylene glycol (PEG) on heat transfer characteristics of PEG/water quenchants with concentrations of 5, 10, and 20 vol% was studied. The cooling curve analysis is performed to assess the cooling characteristics. Spatially dependent surface heat flux transients are estimated using the inverse heat conduction method. The rewetting kinematics is analyzed by videography and acoustic analysis of polymer film rupture during quenching. The results indicated that an increase in the molecular weight of PEG from 200 to 6000 changed the rewetting kinematics from a local wetting front movement to an instantaneous rupture of the polymer film. The change in the rewetting kinematics is reflected in the surface heat flux, indicating an increased uniformity of heat transfer. The film rupture acoustics showed that the polymer film's instantaneous breakup had a higher sound intensity than the one showing wetting front motion. © 2023 Elsevier Inc.