Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
16 results
Search Results
Item Experimental studies on shear strength characteristics of alkali activated slag concrete mixes(Elsevier Ltd, 2020) Manjunath, R.; Narasimhan, M.C.; Shashanka, M.; Vijayanand, S.D.; Vinayaka, J.In the present study an attempt has made to study the shear strength characteristics of alkali activated slag concrete mixes developed using steel slag sand and Electric Arc Furnace (EAF) slag aggregates, respectively, as the fine and coarse aggregates. These mixes use the ground granulated blast furnace slag (GGBFS) as the primary source material. Thus it is to be recognized that all the three materials used-GGBFS, slag sand and EAF slag aggregates are by-products of the Iron and Steel Industry, and are available in very large quantities demanding safe disposal. Different amounts of Sodium silicate solutions, with specified amounts of Sodium hydroxide flakes dissolved in them, are used as alkaline solutions. The test results indicate higher compressive strengths values for all the mixes in the range of 50-70 MPa with their shear strength values ranging between 7.5 and 12.0 MPa. Further the relationship between shear strength and compressive strength of the AASC mixes was also developed. © 2019 Elsevier Ltd. All rights reserved.Item Performance of Alternate Superplasticizers on Performance of Self-compacting Geopolymer Mortars—An Experimental Study(Springer Science and Business Media Deutschland GmbH, 2024) Prakash, G.B.; Mahendra, K.; Tanush, L.; Narasimhan, M.C.Geopolymer binders are the best alternatives to Ordinary Portland cement in the view of carbon impact on the environment. The effect of addition of different types of superplasticizers (SPs) on the flow and compressive strengths of a class of self-compacting geopolymeric mortar (SCGM) mixes is investigated in the present study. Three different kinds of SPs, namely modified Polycarboxylate Ether (MPCE), Polycarboxylate Ether (PCE), and Sulfonated Naphthalene Formaldehyde (SNF), were used in the production of SCGM with varying proportions at 1, 1.5, and 2% by weight of the binder. Results revealed that modified PCE-based SP showed better results in flow and compressive strength (CS) in comparison to PCE and SNF-based SPs. However, an increase in the dosage of SP had less/adverse effect on the flow properties. A maximum slump flow of 270 mm was observed for a modified PCE-based SP at 1.5% dosage, while the highest CS of 34 MPa was observed at 1.5% dosage of the same SP. Scanning electron microscope (SEM) analyses were carried out on a few selected SCGM mixes. © The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd. 2024.Item Shear Strength Characteristics of One-Part Alkali Activated Concrete Mixes—A DOE Approach(Springer Science and Business Media Deutschland GmbH, 2024) Mahendra, K.; Prakash, G.B.; Shetty, S.; Narasimhan, M.C.Utilization of one-part alkali-activated concrete (OPAAC) mixes is an advantageous option for large-scale construction applications. In the present investigation, the main objective was to investigate the shear strength characteristics of OPAAC mixes that were made using GGBFS and fly ash as precursors and sodium meta-silicate as solid activator. Taguchi’s DOE approach has been used to reduce the experimental effort and to find the optimum parameters. An initial set of nine OPAAC mixes was identified based on an L-9 array, with three representative levels considered for each of three principal mix parameters and experiments were conducted to test their compressive and shear strengths. The test results revealed that the OPAAC mixes exhibited 28-day compressive strength values ranging from 55 to 70 MPa, with shear strengths varying in the range of 8.5–12.67 MPa. Multi-linear regression equations were then developed to predict the 28-day compressive and shear strengths using MINITAB 21 statistical software. The predictions of these were verified by conducting actual strength experiments on a new set of three verification mixes. Further, additionally, a generalized correlation was developed to predict the 28-day shear strength of OPAAC mixes based on the known 28-day compressive strength. Again, an examination of microstructures was carried out through the utilization of FESEM analysis, to get a general appreciation of the microstructure (morphology) and elemental composition using EDX analysis of these mixes. The outcomes of this study are anticipated to promote the extensive adoption of environmentally friendly and sustainable materials within the construction industry. The findings of this study are anticipated to promote the extensive adoption of environmentally friendly and sustainable materials in the construction industry. © The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd. 2024.Item Study of the properties of SCC with quarry dust(2009) Gowda, M.R.; Narasimhan, M.C.; Karisddappa; Rajeeva, S.V.Granite fines or rock dust is a by-product obtained during crushing of granite rocks and is also called quarry dust (QD). This paper deals with using quarry dust as an alternative to fine aggregate (FA) in SCC and reports the strength behaviour and hardened properties of such SCCs. Although in normal concretes, introducing QD increases the water demand, in SCC, it has been successfully used for increasing the deformability and passing ability of fresh concrete. Also, it was noted that by increasing the pouring heights of an SCC, the compressive strength and splitting tensile strength of concrete were unaffected.Item Studies on Uniaxial compressive strength of laterite masonry prisms(2011) Unnikrishnan, S.; Narasimhan, M.C.; Venkataramana, K.Laterite is a well known conventional building material in Asian countries. In spite of its large popularity in construction, a systematic characterization of this material, as a building block, has not been seriously attempted so far. The strength and elastic properties of laterite masonry are influenced by the individual properties of the laterite blocks and the mortar. In the present study, characterization of the laterite block and the mortar and compressive strength of laterite masonry prisms have been investigated using detailed laboratory experiments and numerical analysis. The experimental results, related to the compressive strength and stress-strain characteristics of laterite and mortar and compressive strength of laterite masonry prisms are presented. Finite element analysis of laterite masonry prism has also been carried out. The studies have shown that the modulus of elasticity of laterite blocks tested is less than that of mortar used in making the laterite masonry. Further, the laterite masonry prisms have been observed to have failed by bond failure and subsequent splitting of laterite blocks. Also, increase in thickness of mortar joint gives rise to a decrease in laterite tensile stresses in mortar joint leading to higher prism strengths, if bond remains intact. © 2011 CAFET-INNOVA technical society. All right reserved.Item High temperature performance of self-compacting high-volume fly ash concrete mixes(2011) Amrutha; Nayak, G.; Narasimhan, M.C.; Rajeeva, S.V.Quite often, concrete in structures is likely to get exposed to high temperatures, including an incident of fire. The strength-retention properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. This paper presents an experimental study on the strength retention and impermeability aspects of a set of self compacting, high-volume fly ash concrete mixes under elevated temperatures. Five selfcompacting concrete mixes with a higher 60% level of cement replacement with fly-ash, are designed and the effects of elevated temperatures, in the range of 200-800 C, on the physical, mechanical and durability properties of these mixes are assessed. The assessment is in terms of the weight losses and the reduction in the compressive strengths of concrete cubes and split tensile strengths of concrete cylinders. The durability characteristics are assessed in terms of RCPT test results on these mixes. Performances of these self compacting concrete mixes (SCC) at elevated temperatures are also compared with two normally-vibrated concrete mixes (NCs) of an equivalent M30 strength grade. Test results indicate that weight of the specimens significantly get reduced with an increase in the level of elevated temperature, with sharp variations beyond 600 C. The experimental results also show that large improvements against chloride-ion penetration and better strength-retention at higher temperatures can be realized with self-compacting high-volume fly-ash concrete mixes additionally admixed with GGBFS and silica fume.Item Predicting compressive strength of SCC mixtures using artif icial neural network(2012) Rame Gowda, M.; Narasimhan, M.C.; Karisiddappa; Kumuda, T.Over the last few years, the use of artificial neural networks (ANNs) has increased in many areas of engineering. In particular it is increasingly being used in concrete engineering problems. Since accurate estimation of compressive strength of self-compacting concrete (SCC) is an important issue in concrete engineering this paper describes the development of ANN models based on laboratory SCC mixes. The multilayer feed-forward type network models were trained using the back-propagation method with a momentum factor. The data obtained from the mix design exercises were employed to develop and test the performance of the models. A new concept of using more than one error statistic resulted in efficiently training the models and improving its generalization capability.Item An experimental investigation on self-compacting alkali activated slag concrete mixes(Elsevier Ltd, 2018) Manjunath, R.; Narasimhan, M.C.In present work, an attempt has been made to develop self-compacting, alkali activated slag concrete mixes, using steel slag sand as fine aggregate and EAF (Electric Arc Furnace) slag as coarse aggregate. The study investigates the properties such as compressive strength, splitting tensile strength and water absorption of these mixes. Development of Self-Compacting Alkali Activated Slag Concrete mixes (hereafter referred to as SCAASC mixes) was made with GGBFS (Ground Granulated Blast Furnace Slag) as the binder, with its content varying between 700 kg/m3 and 900 kg/m3 of fresh concrete. The net W/B (water to binder) ratio of the mixes was varied between a narrow 0.47 – 0.48 range. The alkaline solutions had Na2O percentages in the range 7 – 9%, but a constant activator modulus was maintained at 1.0 in all the mixes. In order to optimise the number of trial mixes to be tested, Taguchi's design of experiments methodology was adopted. A total of nine mixes were formulated using Taguchi orthogonal L9 array. Results showed the slump flow values for the mixes greater than 700 mm, with their L–Box ratios and V-Funnel values ranging between 0.90 and 0.95 and 9 – 11 s respectively, satisfying the EFNARC guidelines. Results also showed good compressive strengths (65–80 MPa), split-tensile strengths (2–4 MPa) and low water absorption values in the range of (2%–3%). The microstructural studies such as SEM, EDX and XRD analysis were also carried out, showing denser morphologies clearly indicating effective activation of slag by the alkaline solution. © 2018 Elsevier LtdItem Studies on development of high performance, self-compacting alkali activated slag concrete mixes using industrial wastes(Elsevier Ltd, 2019) Manjunath, R.; Narasimhan, M.C.; Umesh, K.M.; Kumar, S.; Bala Bharathi, U.K.In the present study, development of a class of High Performance Alkali Activated Slag Concrete mixes (hereafter referred to as HPAASC mixes) is discussed. These mixes are developed using three industrial wastes from Iron and Steel industry. While Ground granulated blast furnace slag (GGBFS) was used as the main binder, in the development of these HPAASC mixes, steel slag sand and Electric Arc Furnace slag (EAF slag) have been employed in the fine aggregate and coarse aggregate fractions of them. Higher flow characteristics, as those of self-compacting concrete mixes, as well as enhanced mechanical strength properties of these mixes are discussed in detail. The alkaline solutions used consist mixtures of sodium hydroxide and sodium silicate solutions, with a constant activator modulus (ratio of SiO2/Na2O) of one maintained in them. Taguchi’ design of experiments methodology was used to reduce the experimental efforts. The formulation of all the mixes developed herein was based on Taguchi's L-9 orthogonal array. Flow and strength properties of a set of nine mixes were used for performance evaluation purposes in an initial, calibration phase. Strength prediction equations were derived based on such results, the predictive capability of which were then assessed and ascertained with actual results of experiments on the next six new mixes, in the prediction phase. Test results indicated a higher flowability values for all the mixes (with slump flows greater than 700 mm), good filling and passing abilities, all satisfying the EFNARC (European Federation of Specialist Construction Chemicals and Concrete Systems) recommendations for SCC mixes. Higher compressive strengths (65–90 MPa), split-tensile strengths (4.8–5.3 MPa), flexural strengths (6.5–7 MPa), and Modulus of Elasticity (30.4–36.2 GPa) were observed along with lower water absorption values (2.1–2.7%) for all the HPAASC mixes tested herein. Microstructure studies were conducted on samples from the fractured surfaces of test specimens from different mixes, using advanced SEM, EDX and XRD analyses and the results are discussed. © 2018 Elsevier LtdItem Studies on high performance alkali activated slag concrete mixes subjected to aggressive environments and sustained elevated temperatures(Elsevier Ltd, 2019) Manjunath, R.; Narasimhan, M.C.; Umesha, K.M.In contemporary constructions, there is a continuous drive for enhancing the performances of concrete mixes, both green and as well as on hardened state. Again there are simultaneous efforts to take full advantage of all the various fast-track, state-of-art construction technologies, leading to early completion of efficient, economical and eco-friendly infrastructure projects. The present authors have developed a new class of high performance self-compacting, alkali activated slag concrete mixes (HPAASC) using three industrial by-products, all obtained from iron and steel industry and have evaluated them for their strength properties. While these HPAASC mixes have higher compressive strengths (about 70–90 MPa) and reasonable split-tensile and flexural strengths, they are also self-compacting in nature. In the present paper, the durability performance of this class of mixes on long-term exposure to aggressive environments like acids, sulphates and chlorides is discussed. Strength deteriorations of the standard test specimens subjected to 5% concentrated sulphuric acid solution and so also in 10% magnesium sulphate solution were monitored for a period of one year. The impermeability of the mixes against chloride-ions was evaluated using both Bulk diffusion test (BDT) and the Rapid chloride penetration test (RCPT). Further these mixes were also evaluated for their performance on exposure to sustained elevated temperatures in the range of 200–800 °C. All the specimens were further analysed for their microstructural studies. Results in the present study indicate that, all the HPAASC mixes exhibit better resistances to aggressive environments and sustained elevated temperatures as compared to the OPC-based reference concrete mix. © 2019 Elsevier Ltd