Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item ZnO/carbon nanotube nanocomposite for high energy density supercapacitors(2013) Aravinda, L.S.; Nagaraja, K.K.; Nagaraja, H.S.; Bhat, K.; Badekai Ramachandra, B.A facile, green and highly efficient method for the decoration of carbon nanotubes with ZnO was developed for the fabrication of binder-free composite electrode for supercapacitor applications. The nano composite was prepared by using reactive magnetron sputtering in Ar/O2 environment. This approach leads to more uniform coating with tuneable thickness, which alters the electrochemical performance of the nano composite electrodes. The structure and surface morphology of the composite film have been studied by means of X-ray diffraction (XRD) analysis, scanning electron microscopy and field emission scanning electron microscopy (FESEM). The XRD study reveals the formation of Wurtzite ZnO structure. The electrochemical performance of nano composite electrode was investigated using cyclic voltammetry, chronopotentiometry and electrochemical impedance measurements in non-aqueous electrolyte. The nano composite electrode shows significant increase in the specific capacitance up to 48 F g-1 with an energy density 13.1 Wh kg-1 in the potential range -2 V to 1 V. © 2013 Elsevier Ltd. All rights reserved.Item Design and fabrication of spectrally selective TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO tandem absorber for higherature solar thermal power applications(Elsevier, 2015) Jyothi, J.; Chaliyawala, H.; Srinivas, G.; Nagaraja, H.S.; Barshilia, H.C.A new nanostructured TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO tandem absorber has been designed for higherature solar thermal power applications. The first three layers in this tandem act as an absorbing layer, whereas, TiAlSiCO and TiAlSiO act as semi-transparent and anti-reflecting layers. The tandem absorber was deposited on stainless steel substrates using a four-cathode reactive direct current unbalanced magnetron sputtering system. The composition and thicknesses of the individual component layers have been optimized by adjusting the reactive flow rate of C2H2, N2, O2, and also Al, Ti and Si target power densities to achieve high absorptance (0.961) and low emittance (0.07 at 82 °C). The reflectance data showed that the absorptance increases gradually with shift of reflectance minimum to higher wavelengths from first layer to last layer (i.e., TiAlC to TiAlSiO). The thickness of optimized tandem absorber was calculated from the cross-sectional field-emission scanning electron microscopy images and confirmed using transmission electron microscopy. The performance evaluation of the tandem absorber has been evaluated by heating it in air and vacuum under cycling conditions at different temperatures. These results showed that the tandem absorber was stable up to 325 °C in air for 400 h and up to 650 °C in vacuum for 100 h, thus demonstrating its suitability for higherature solar thermal power generation applications. © 2015 Elsevier B.V. All rights reserved.Item Morphology-dependent electrochemical performances of nickel hydroxide nanostructures(Indian Academy of Sciences, 2019) Bhat, K.S.; Nagaraja, H.S.Electrochemical capacitors form part of the developing technologies in the field of alternative energy sources. In the present work, nickel hydroxide (Ni(OH) 2) nanosheets and microflowers are hydrothermally prepared employing different chemical precursors. Structure, morphology and chemical analysis are conducted using powder X-ray diffraction, field emission scanning electron microscopy and energy-dispersive X-ray spectroscopy measurements. Electrochemical performances as supercapacitor electrodes of the synthesized nanostructures are evaluated through cyclic voltammetry and galvanostatic charge–discharge measurements with three-electrode configurations. The results indicated the specific capacitance of 180 and 417Fg-1 at a scan rate of 5mVs-1 for Ni(OH) 2 nanosheets and microflowers, respectively. The higher specific capacitances for Ni(OH) 2 microflowers could be attributed to the higher specific surface area, morphology, electronic conductivity and porosity. Both Ni(OH) 2 nanostructures exhibited good capacitance retention for 1500 cycles. © 2019, Indian Academy of Sciences.Item Impact of copper doping on the electrochemical response of MnSe2 as anode for lithium-ion battery(Springer, 2024) Mukesh, P.; Lakshmi Sagar, G.; Brijesh, K.; Kumawat, S.; Hegde, A.; Kumar, A.; Nagaraja, H.S.Transition Metal Chalcogenides (TMC), due to their unique physicochemical properties, are studied in various fields and have potent applications in energy storage applications. This work is based on the synthesis and characterization of copper-doped manganese di-selenide and the effect of its doping on electrochemical performance as anode material for lithium-ion battery applications using the solvothermal method. The characterization techniques used are X-ray diffraction, Raman spectroscopy, field-emission scanning electron microscopy, XPS, UV–visible absorption spectroscopy, and electrochemical analysis. The XRD data confirms the formation of MnSe2 exhibiting Cubic crystal geometry. The FESEM images show the micro-cube-like structure with agglomerated nanocluster nanostructures on the surface with a dimension of 100–200 nm. The doping of the copper has decreased the band gap of the MnSe2, as studied by the UV–visible absorption spectrum. The electrochemical performance is analyzed as anode material for lithium-ion batteries. The charge/discharge measurements show a specific capacity of 706 mAh g−1 as the initial discharge capacity and 336 mAh g−1 as the initial charge capacity at 0.1 A g−1 current density. Meanwhile, 3% Copper-doped MnSe2 showed a better specific capacity of 878 mAh g−1 as the initial discharge capacity and 461 mAh g−1 as the initial charge capacity at 0.1 A g−1 current density. Cyclic stability, rate capability, and electrochemical impedance spectroscopy were performed, and it shows that 3% copper-doped MnSe2 has good stability and better conductivity and charge kinetics, indicating copper doping has enhanced the electrochemical performance of pristine MnSe2. © The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature 2024.Item Synergistic boost in Fe3O4 anode performance for li-ion batteries via Zn and Cu double doping and multi-walled carbon nanotube composite integration(Elsevier B.V., 2024) Kumar, A.; Mukesh, P.; Lakshmi Sagar, G.; Hegde, A.; Nagaraja, H.S.In this study, a novel nanocomposite material comprising pure Fe3O4 (FO), doped Zn0.5Cu0.5Fe2O4-3 (ZCFO-3), and Zn0.5Cu0.5Fe2O4-3@ Multi-walled carbon nanotube (ZCFO-3@MWCNT) nanocomposite material is carefully prepared using a simple one-step hydrothermal process. Comprehensive surface and morphological analysis are conducted using X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), and High-resolution transmission electron microscopy (HRTEM), while compositional studies are investigated through Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). The electrochemical performance is fully analyzed through Cyclic voltammetry (CV), Electrochemical impedance spectroscopy (EIS), rate capability tests, discharge/charge capacity, and cyclic stability evaluations. Among these three nanomaterials, ZCFO-3@MWCNT nanocomposite at 100 mA g−1 current density reveals the best performance, with a discharge capacity of 1974 mAh g–1, ZCFO-3 and FO reveal 1340 mAh g–1 and 1317 mAh g–1 respectively. After 800 cycles at 500 mA g−1 current density, ZCFO-3@MWCNT stays strong with a discharge capacity of 646 mAh g–1, while ZCFO-3 manages only 362 mAh g–1 and FO only 111 mAh g–1. After 1200 cycles at 500 mA g−1, the nanocomposite still delivers 518 mAh g–1. This study suggests that ZCFO-3@MWCNT could be a promising anode material for lithium-ion batteries. © 2024 Elsevier B.V.Item Novel Ag2Cu2O3 nanorods as stable anode material for lithium-ion battery(Elsevier B.V., 2025) Kumar, A.; Sagar G, L.; P, M.; Hegde, A.P.; Nagaraja, H.S.In this research novel Ag2Cu2O3 nanorods was prepared, for lithium-ion battery as anode, using facile co-precipitation method with four different stirring time and correspondingly Ag2Cu2O3 named ACO – 30 M, ACO – 12 H, ACO – 24 H, and ACO – 36 H. Field Emission Scanning Electron Microscopy (FESEM) and High-Resolution Transmission Electron Microscopy (HRTEM) analyze surface and morphology, while X-ray Diffraction (XRD) examines structural properties. Compositional analysis is carried out using X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The electrochemical analysis is evaluated by cyclic stability, rate capability, discharge/charge capacity, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The ACO – 24 H nanomaterial demonstrates an initial discharge capacity of 943 mAh g?1 at a current density of 50 mA g?1. Among the four materials tested, ACO – 24 H shows superior cycling performance, with a discharge capacity of 174 mAh g?1 at 200 mA g?1 after 1003 cycles. In comparison, ACO – 30 M, ACO – 12 H, and ACO – 36 H exhibit capacities of 134 mAh g?1, 91 mAh g?1, and 43 mAh g?1, respectively, under the same conditions. This study suggests that ACO – 24 H is a promising anode material for lithium-ion battery applications. © 2025 Elsevier B.V.