Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Mithun, B.M.Subject: search.filters.subject.Concretes

Search Results

Now showing 1 - 5 of 5
  • No Thumbnail Available
    Item
    Influence of silica fume on the strength of betostyrene mixed concrete
    (2013) Sambo, A.G.; Deepak, T.J.; Mithun, B.M.
    The main objective of this paper is to determine the influence of silica fume (SF) on betostyrene mix concrete. Extensive experimentation was carried out to determine the influence of SF on the workability, compressive strength and flexural strength of concrete at constant water-binder ratio of 0.40 and SF additive of 0%, 5%, 10%, and 15%. For all mixes, slump test, compaction factor, compressive and flexure strengths were determined at 7, 14 and 28 days. The results showed that the compressive and flexure strengths increased with silica fume incorporation. This study comprehensively produced lightweight concrete and showed a rise in strength as in direct proportionality to the increase in silica fume. Workability fell to a rising amount of silica fume. © 2013 CAFET-INNOVA TECHNICAL SOCIETY.
  • No Thumbnail Available
    Item
    Air-cured Alkali activated binders for concrete pavements
    (Chinese Society of Pavement Engineering, 2015) Palankar, N.; Ravi Shankar, A.U.; Mithun, B.M.
    The present study focuses on the possibility of use of alkali activatedbinders for use in concrete pavements. Alkali Activated Slag Concrete (AASC) and Alkali Activated Slag Fly ash Concrete (AASFC) are prepared and the properties are compared with Ordinary Portland Cement Concrete (OPCC). The Ground Granulated Blast FurnaceSlag (GGBFS) and Fly Ash (FA) are blended in the ratios 100:0, 75:25, 50:50 and 25:75 as binder and activated using strong alkaline solution. Trial mixes are carried out to identify the optimal Activator Modulus (Ms) for each combination of GGBFS and FA. The mix design for the optimal activator modulus is optimised to achieve sufficient strength for Pavement Quality Concrete (PQC) and the fresh and mechanical properties are studied in detail. The results indicate the properties of AASC and AASFC are similar or slightly better than conventional OPCC and satisfy the minimum strength requirements for concrete pavements. The application of alkali activated binders will minimise the environmental hazards occurring from augmented OPC production, along with effective utilisation of industrial waste materials and conservation of natural resources. © Chinese Society of Pavement Engineering.
  • No Thumbnail Available
    Item
    Performance of alkali activated slag concrete mixes incorporating copper slag as fine aggregate
    (Elsevier Ltd, 2016) Mithun, B.M.; Narasimhan, M.C.
    In this present study, copper slag (CS) is proposed as an alternative to river sand as fine aggregate in alkali-activated slag concrete (AASC) mixes. The relative performance of alkali activated slag concrete mixes with CS as fine aggregate is compared to conventional Ordinary Portland Cement concrete (OPCC) mix in terms of their workability, strength and durability parameters. The results indicate that, AASC mixes with CS, as a replacement to sand upto 100% (by volume), show no marked loss in strength characteristics. AASC mixes with either sand or CS possess similar modulus of elasticity, lower total porosity, lesser water absorption and reduced chloride ion penetration as compared to OPCC. Strength-retention characteristics of AASC mixes with sand/CS on exposure to sulphate and acid-rich environment are also studied. Use of AASC mixes for structural application reduces carbon footprint, decreases water consumption and cost. Use of CS as fine aggregate reduces river sand consumption as an added benefit. © 2015 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    Item
    Durability studies on eco-friendly concrete mixes incorporating steel slag as coarse aggregates
    (Elsevier Ltd, 2016) Palankar, N.; Ravi Shankar, A.U.; Mithun, B.M.
    The present study discusses the durability performance of alkali activated concrete mixes containing steel slag as coarse aggregates. Steel slag aggregates, a waste product obtained from iron and steel industry are incorporated as coarse aggregates in alkali activated slag concrete (AASC) and alkali activated slag fly ash concrete (AASFC) by replacing traditional natural aggregates. The mix design for AASC and AASFC mixes are optimised to obtain sufficient strength for structural purposes and then steel slag coarse aggregates are incorporated at different replacement levels (0%, 50% and 100% by volume of total coarse aggregate content). Durability properties such as long term ageing performance, water absorption, volume of permeable voids, resistance to sulphuric acid attack and resistance to magnesium sulphate attack are studied in detail and compared with conventional Ordinary Portland Cement Concrete (OPCC). The ecological and economical analysis of concrete mixes is also carried out. It was found that the AASC and AASFC mixes displayed better durability performance as compared to OPCC. The inclusion of steel slag aggregates slightly reduced the durability performance of AASC and AASFC mixes. The AASC and AASFC with steel slag aggregates displayed lower energy requirement and lower production cost as compared to OPCC, thus proving it to be eco-friendly. © 2016 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    Item
    Investigations on Alkali-Activated Slag/Fly Ash Concrete with steel slag coarse aggregate for pavement structures
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2017) Palankar, N.; Ravi Shankar, A.U.; Mithun, B.M.
    The present investigation is conducted to evaluate the effect of steel slag coarse aggregates on mechanical properties and fatigue behaviour of Alkali-Activated Slag Fly Ash Concrete (AASFC) mixes. AASFC mixes were prepared with steel slag coarse aggregates by replacing natural coarse aggregates at various replacement levels (0, 25, 50, 75 and 100% by volume). Various mechanical properties and fatigue performance were tested and compared with conventional Portland concrete. The incorporation of steel slag aggregates resulted in decrease in mechanical strength of AASFC mixes. The fatigue lives of AASFC mixes containing steel slag were found to be lower than AASFC with natural coarse aggregates. Two-parameter Weibull distribution was used for statistical analysis of fatigue data and it was observed that the fatigue data of concrete mixes can be approximately modelled using Weibull distribution. Steel slag aggregates reported acceptable performance in AASFC mixes for its use in pavement quality concrete. © 2015 Informa UK Limited, trading as Taylor & Francis Group.