Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Elevated temperatures erosion wear behavior of HVOF sprayed WC-Co-Cr/Mo coatings on Ti6Al4V substrate(Elsevier B.V., 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.The present research aims to investigate the effect of different impact angles and temperatures on volumetric erosion loss of WC-Co-Cr coating containing 10 wt% Mo. The composite coating was developed using High-Velocity Oxy Fuel (HVOF) process on a titanium substrate (Ti-31). A solid particle erosion behavior of the coatings is carried out at different impact angles (30°, 60°, and 90°) and temperatures (200 °C, 400 °C,600 °C, and 800 °C). The volumetric erosion loss of the coated samples was measured using an air jet erosion tester at high temperatures using Al2O3 as an erodent. The XRD, SEM/EDS, porosity, density, microhardness, bond strength, and scratch tests characterized the as-sprayed coatings. The 3D optical profilometer was employed to evaluate the volumetric erosion loss and the mode of erosion. The scratch resistance of WC-Co-Cr coating is better than WC-Co-Cr/Mo coating. The WC-Co-Cr coating shows a brittle mode of erosion up to 600 °C and a ductile mode of erosion at 800 °C. In contrast, the WC-Co-Cr/Mo coating shows a brittle mode of erosion at 200 °C and a mixed mode of erosion at 400 °C to 800 °C. The volumetric erosion loss of WC-Co-Cr is less than WC-Co-Cr/Mo for all temperatures and impact angles. The formation of oxide phases on the coating surfaces demonstrates erosion resistance at high temperatures. The results of volumetric erosion loss measured by the weight loss method correlate well with a non-contact type 3D optical profilometer. © 2023 Elsevier B.V.Item Effect of Impact Angles and Temperatures on the Solid Particle Erosion Behavior of HVOF Sprayed WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY Coatings(Springer, 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.Extreme erosion wear from elevated temperature caused by the impact of entrained solid particles in the fluid stream primarily affects aerospace components and marine parts. This work focuses on increasing the base material erosion resistance by applying thermally sprayed carbide-based coatings. A high-temperature Solid particle erosion behavior of WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY coatings deposited by the HVOF process on a titanium-31 was evaluated using an air-jet erosion tester. The erosion test was conducted utilizing alumina erodent of grit size 35-50 µm. The effects of impact angles (30°, 60°, and 90°) and temperatures (200-800 °C) on the erosion performance of two coatings are compared. The feedstock powder and as-sprayed coatings were characterized for micro-structure phase composition, porosity, density, micro-hardness, and adhesion strength. SEM/EDS and a 3D optical profilometer were used to examine eroded samples further to determine the erosion mode. The Cr3C2-CoNiCrAlY coating shows a brittle mode behavior of erosion at 200-400 °C and ductile mode behavior of erosion at 600-800 °C. In contrast, the WC-Co/NiCr/Mo coating shows brittle mode behavior of erosion at 200-400 °C and 600-800 °C, a mixed mode behavior of erosion. The erosion loss in volume of Cr3C2-CoNiCrAlY is lower than WC-Co/NiCr/Mo for all temperatures and impact angles. The development of carbide and oxide phases on the eroded surfaces demonstrates increasing erosion resistance at high temperatures. The optical profilometer measures the volumetric erosion loss, compares it with the weight loss method, and finds consistency between them. © 2023, ASM International.Item Studies on high temperature erosion behavior of HVOF-sprayed (Cr?C?-NiCr)Si and WC-Co/NiCrAlY composite coatings(Elsevier Ltd, 2025) Medabalimi, S.; Hebbale, A.M.; Gudala, S.; Rokkala, U.; Ramesh, M.R.The present study investigates the high temperature erosion behavior of HVOF sprayed composite coatings on T11 steel substrates by studying (Cr?C?-NiCr)Si and WC-Co/NiCrAlY coatings. Phase composition, cross sectional microstructure, mechanical properties, and erosion resistance were analyzed by XRD, EDS, SEM and three-dimensional optical profilography. The results demonstrate that the WC-Co/NiCrAlY coating has higher erosion resistance and oxidation stability for all temperatures and impact angles tested. Its enhanced performance in high temperature and erosive conditions is attributable to the formation of stable protective oxides such as Al?O? and Cr?O? and intermetallic phases such as Ni?Al and Cr?C?. The NiCrAlY matrix prevents significant decarburization of WC particles, and hence phase stability and oxidation resistance. The (Cr?C?-NiCr)Si coating has higher microhardness due to silicide phases, but is more vulnerable to direct impacts and inferior oxidation resistance. The phase transformations for both coatings are favorable at elevated temperatures which enhances erosion resistance. The WC-Co/NiCrAlY coating is smooth and shallower in erosion craters and is perfectly suited for harsh environments demanding high toughness, impact resistance and oxidation stability. For applications in which high hardness is needed in less severe conditions, the (Cr?C?-NiCr)Si coating is more suitable. © 2024Item Studies on high-temperature erosion behaviour of HVOF sprayed NiCr based composite coatings(Elsevier B.V., 2025) Medabalimi, S.; Hebbale, A.M.; Gudala, S.; Ramesh, M.R.; Gujar, R.; Aravindan, N.; Petr?, J.Solid particle erosion at high temperature is a major problem in many industries and advanced protective coatings are needed to extend the service life of components subjected to harsh environment. The main objective of this study is to investigate the erosion behavior of HVOF sprayed (NiCr) + 5 % Si and (NiCr)+ 2% C based composite coatings at different impact angles and temperature, with specific emphasis on the effect of coating composition. The coatings exhibited excellent erosive wear resistance at elevated temperatures due to the formation of stable oxide layers (CrO, NiCr?O?, SiO?) and the incorporation of silicide phases (Ni?Si) to the NiCrSi coatings. However, NiCrC coatings containing hard carbide phases (such as NiC) showed higher erosion resistance at higher temperatures and normal impact angles (90°) because of their robust microstructure and thermal stability. The analysis of microhardness indicated that NiCrSi coatings provided higher hardness attributable to silicides and were therefore better suited to moderate erosive environments, whereas NiCrC coatings, with slightly lower hardness, exhibited excellent resilience under severe erosive environments. SEM, EDAX and XRD analyses showed that preferential erosion mechanisms were cutting and plowing at oblique angles (30°) and brittle fracture at normal angles (90°). Notably, at 800 °C, NiCrC coatings outperformed the NiCrSi coatings via consistently superior thermal and erosion resistance. These findings indicate that HVOF sprayed NiCrC coatings are suitable for high temperature erosion protection, and NiCrSi coatings are specifically developed for high erosive wear resistance at low impact angles. © 2025 The Author(s)