Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Effect of Microwave Hybrid Heating on High-Temperature Adhesive Wear Behavior of High-Velocity Oxygen Fuel-Sprayed WC-CrC-Ni and WC-Co/NiCrFeSiB Coatings(Springer, 2023) Medabalimi, S.; Ananthu, M.R.; Gudala, S.; Ramesh, M.R.HVOF-processed coatings are chemically inhomogeneous and are not metallurgically bonded to the substrate. As a result, components coated with HVOF experience considerable material degradation during sliding wear. Microwave hybrid heating (MHH) is a novel surface modification technique for modifying the as-sprayed properties of the coating. Hence, this paper investigates and compares the wear and frictional behavior of HVOF as-sprayed coatings against MHH samples of WC-CrC-Ni and WC-Co/NiCrFeSiB coatings at elevated temperatures. MHH had a significant impact on wear rate and coefficient of friction by optimizing the porosity, integrated oxide phases and intersplat cohesion strength of the coatings. A modified domestic oven was used to perform MHH on HVOF-coated samples for 5 min at 1200 °C. Wear tests were performed using a pin-on-disk tribometer from room temperature to 200, 400, and 600 °C with Al2O3 disk as a counterface. SEM/EDS and XRD were utilized to examine the microstructural characterization of the coatings and substrate. Both the coatings showed higher wear resistance than the substrate at all temperatures. The WC-Co/NiCrFeSiB coating produced an oxide layer on the worn surfaces and integrated WC, CoWO4, and Fe2SiO4 splats, enhancing wear resistance. The MHH WC-CrC-Ni coating formed Cr2O3 and NiWO4 phases on the worn surfaces, increasing the intersplat cohesion strength between matrix and carbide splats, lowering the overall wear rate. After MHH, the wear rate of a substrate and WC-CrC-Ni coating was 3.5 and 1.12 times more at room temperature and 8.07 and 2.92 times more at 600 °C than WC-Co/NiCrFeSiB coating. © 2022, ASM International.Item Elevated temperatures erosion wear behavior of HVOF sprayed WC-Co-Cr/Mo coatings on Ti6Al4V substrate(Elsevier B.V., 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.The present research aims to investigate the effect of different impact angles and temperatures on volumetric erosion loss of WC-Co-Cr coating containing 10 wt% Mo. The composite coating was developed using High-Velocity Oxy Fuel (HVOF) process on a titanium substrate (Ti-31). A solid particle erosion behavior of the coatings is carried out at different impact angles (30°, 60°, and 90°) and temperatures (200 °C, 400 °C,600 °C, and 800 °C). The volumetric erosion loss of the coated samples was measured using an air jet erosion tester at high temperatures using Al2O3 as an erodent. The XRD, SEM/EDS, porosity, density, microhardness, bond strength, and scratch tests characterized the as-sprayed coatings. The 3D optical profilometer was employed to evaluate the volumetric erosion loss and the mode of erosion. The scratch resistance of WC-Co-Cr coating is better than WC-Co-Cr/Mo coating. The WC-Co-Cr coating shows a brittle mode of erosion up to 600 °C and a ductile mode of erosion at 800 °C. In contrast, the WC-Co-Cr/Mo coating shows a brittle mode of erosion at 200 °C and a mixed mode of erosion at 400 °C to 800 °C. The volumetric erosion loss of WC-Co-Cr is less than WC-Co-Cr/Mo for all temperatures and impact angles. The formation of oxide phases on the coating surfaces demonstrates erosion resistance at high temperatures. The results of volumetric erosion loss measured by the weight loss method correlate well with a non-contact type 3D optical profilometer. © 2023 Elsevier B.V.Item Effect of Impact Angles and Temperatures on the Solid Particle Erosion Behavior of HVOF Sprayed WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY Coatings(Springer, 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.Extreme erosion wear from elevated temperature caused by the impact of entrained solid particles in the fluid stream primarily affects aerospace components and marine parts. This work focuses on increasing the base material erosion resistance by applying thermally sprayed carbide-based coatings. A high-temperature Solid particle erosion behavior of WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY coatings deposited by the HVOF process on a titanium-31 was evaluated using an air-jet erosion tester. The erosion test was conducted utilizing alumina erodent of grit size 35-50 µm. The effects of impact angles (30°, 60°, and 90°) and temperatures (200-800 °C) on the erosion performance of two coatings are compared. The feedstock powder and as-sprayed coatings were characterized for micro-structure phase composition, porosity, density, micro-hardness, and adhesion strength. SEM/EDS and a 3D optical profilometer were used to examine eroded samples further to determine the erosion mode. The Cr3C2-CoNiCrAlY coating shows a brittle mode behavior of erosion at 200-400 °C and ductile mode behavior of erosion at 600-800 °C. In contrast, the WC-Co/NiCr/Mo coating shows brittle mode behavior of erosion at 200-400 °C and 600-800 °C, a mixed mode behavior of erosion. The erosion loss in volume of Cr3C2-CoNiCrAlY is lower than WC-Co/NiCr/Mo for all temperatures and impact angles. The development of carbide and oxide phases on the eroded surfaces demonstrates increasing erosion resistance at high temperatures. The optical profilometer measures the volumetric erosion loss, compares it with the weight loss method, and finds consistency between them. © 2023, ASM International.Item Cyclic Oxidation and Hot-Corrosion Behavior of HVOF-Sprayed NiCrAl Coating on Industrial Boiler Tube Steels(Springer, 2024) Ramesh, M.R.; Medabalimi, S.; Rupanagudi, R.S.; Prasad, C.D.; Sollapur, S.B.At high temperatures, coatings provide a protective scale development on surfaces to maintain long-term stability. In the current study, ASTM-SA210-Grade A1 (GrA1) and ASTM-SA213-T-11 (T11) boiler tube steels were coated with NiCrAl alloy with high-velocity oxy-fuel (HVOF) to prevent oxidation and hot corrosion. For hot corrosion and oxidation, 50 cycles at 900°C were taken into account. Additionally, tests of hot-corrosion behavior were conducted in an atmosphere containing molten salt (Na2SO4-60%V2O5), while tests of oxidation behavior were conducted in static air. The kinetics of oxidation were calculated using the thermogravimetric method. Using XRD, EPMA, and SEM/EDAX methods, the produced oxide scales were characterized. The oxidation rate of NiCrAl-coated steels was found to be lower than that of uncoated steels. The coated steels subjected to oxidation in air exhibit slow scale growth kinetics and oxides of α-Al2O3 and Cr2O3 on the outermost surface, while accelerated oxidation caused by the molten salt exhibits metastable Al2O3. Along the nickel-rich splat boundary, Cr and Al were formed a preferential oxidation, which prevents other oxygen from entering the coating via pores and voids, resulting in steady-state oxidation. © The Minerals, Metals & Materials Society 2024.