Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Photovoltaic Systems Technology(wiley, 2024) Husain, M.A.; Ahmad, W.; Ilahi Bakhsh, F.I.; Padmanaban, P.; Malik, H.Discover comprehensive insights into the latest advancements in solar PV technology, including power electronics, maximum power point tracking schemes, and forecasting techniques, with a focus on improving the performance of PV systems. A huge number of research articles and books have been published in the last two decades, covering different issues of PV efficiency, circuits, and systems for power processing and their related control. Books that have been published cover one or more topics but altogether fail to give a complete picture of the different aspects of PV systems. Photovoltaic Systems Technology aims to close the gap by providing a comprehensive review of techniques/practices that are dedicated to improving the performance of PV systems. The book is divided into three parts: the first part is dedicated to advancements in power electronic converters for PV systems; tools and techniques for maximum power point tracking of PV systems will be covered in the second part of the book; and the third part covers advancements in techniques for solar PV forecasting. The overall focus of the book is to highlight the advancements in modeling, design, performance under faulty conditions, forecasting, and application of solar photovoltaic (PV) systems using metaheuristic, evolutionary computation, machine learning, and AI approaches. It is intended for researchers and engineers aspiring to learn about the latest advancements in solar PV technology with emphasis on power electronics involved, maximum power point tracking (MPPT) schemes, and forecasting techniques. © 2024 Scrivener Publishing LLC.Item A Fault Diagnosis and Postfault Reconfiguration Scheme for Interleaved Boost Converter in PV-Based System(Institute of Electrical and Electronics Engineers Inc., 2021) Ahmad, M.W.; Brahmendra Yadav Gorla, N.B.Y.; Malik, H.; Panda, S.K.To utilize the solar photovoltaic (PV) energy efficiently, dc-dc converters are widely used in both grid-connected and stand-alone systems. Among the various topologies, interleaved dc-dc boost converter offers the benefit of modularity, high power density, and high efficiency along with reduced input current ripple to the PV panel, thereby improving its power extraction efficiency. Open-circuit faults in any of the semiconductor switches of interleaved boost converter could lead to unequal loading on the healthy phases and increase in ripple current that reduces the extraction efficiency of the PV system. To address this issue, a new fault detection and localization scheme is proposed in this article. The proposed scheme utilizes the switching-frequency-based harmonic component for fault detection and localization. Once the fault is localized, a postfault restoration and control strategy is also proposed to ensure equal current sharing among the remaining healthy modules within their maximum current rating and minimize the input current ripple in the PV panel. Detailed simulations are carried out to show the effectiveness of the proposed approach. A laboratory prototype of the interleaved converter is built to validate the proposed approach and experimental test results are provided. © 1986-2012 IEEE.Item Noninvasive Model-Based Open-Circuit Switch Fault Detection of AC-Bypass Leg Switches in Transformerless PV Inverter(Institute of Electrical and Electronics Engineers Inc., 2021) Ahmad, M.W.; Brahmendra Yadav Gorla, N.B.Y.; Malik, H.; Panda, S.K.Transformerless inverters are being used for integrating photovoltaic (PV) sources into the grid. Highly efficient and reliable inverter concept (HERIC) inverter is one such topology, which is derived from an H-bridge by adding a bypass leg on the ac side using two back-to-back insulated gate bipolar transistors (IGBTs). Open-circuit fault in the bypass leg would result in conduction of current through antiparallel diodes of the main switches of the inverter, effectively making the inverter operate in bipolar mode. As a result of the fault, there would not be an issue of leakage current, and the operation would continue at the expense of increased conduction losses and dc-offset in the grid current. This article proposes an online noninvasive model-based technique to detect switch faults in the bypass leg of the HERIC inverter. The grid current at the peak of the carrier signal is predicted based on the measured grid current at the start of the zero states. By comparing the estimated and measured grid currents at the peak of the carrier signal, the faulty switch in the bypass leg is localized. Once the fault is localized, the inverter's modulation scheme is changed to conventional bipolar mode to improve the performance of the converter during the post-fault stage. A detailed simulation study is carried out to verify the effectiveness of the proposed approach. Experimental tests on the prototype converter show that the proposed algorithm can reliably detect the open-circuit fault in switches of the bypass leg, and once a fault is detected, the algorithm would change the modulation scheme to bipolar mode to minimize the inverter loss and dc-offset in the grid current. © 2013 IEEE.Item Development of wide area monitoring system for smart grid application(IOS Press BV, 2022) Malik, H.; Ahmad, M.W.; Alotaibi, M.A.; Almutairi, A.PMU can directly measure positive sequence voltage, phase and system frequency. In this paper, the design and implementation for optimum placement of PMU in power system network (PSN) has been performed using 5 different intelligent approaches at an emulation platform. Different case studies based on IEEE 7, 14 and 30 bus system have been performed and analyzed. In the studies, PMU device is used for the measurement of voltage and current magnitude as well as its phase and its performance has been compared with measured real signals of PSN. PMU measurement gives the accurate results and reliability to PSN. But PMUs are not economical, so PSN operator needs to install a minimum number of PMU in PSN so that system should be fully observable in a real-Time scenario. In this paper for optimal placement of PMU, five different intelligent methods have been analyzed for three different bus systems and obtained results are compared. For the further validation of selected PMUs for the PSN, a state estimation using WLS algorithm has been performed using conventional data and PMU data on IEEE14 and IEEE30 bus systems. The obtained results for voltage estimation error and phase estimation error with and without PMU data are compared. © 2022-IOS Press. All rights reserved.Item A Review of Open-Circuit Switch Fault Diagnostic Methods for Neutral Point Clamped Inverter(MDPI, 2022) Mullali Kunnontakath Puthiyapurayil, M.R.; Nadir Nasirudeen, M.; Saywan, Y.A.; Ahmad, M.W.; Malik, H.Due to numerous advantages, a neutral point clamped (NPC) inverter is a preferred choice for high-power applications and renewable technology. The reliability of the NPC inverter is a major concerning factor during the assessment of system performance as power semiconductor switches are vulnerable to abnormal conditions. Open-circuit (OC) switch faults are not as dangerous as short circuit (SC) faults but eventually have enough potential to cause cascaded failure to other components in the system and thus need to be supervised carefully. The OC faults result in a distortion of voltage and current signals in the NPC converter. Based on these signals, over the past few years, many efforts have been made to identify and localize the OC switch fault to the switch level in the NPC topology. In this paper, a review of different OC switch fault diagnostic methods is provided. Starting from the NPC inverter operation under healthy and faulty conditions, the various possible and unavailable switching states along with the deviation in pole voltage under different switch fault conditions is discussed. Then, based on the approach used for system-based fault detection, the OC fault detection methods are classified. The various OC methods are further discussed on the basis of signal, i.e., current, voltage or a combination of both signals used as a signature for fault detection. Emphasis is given to the principle involved, diagnostic variables utilized, the implementation approach and the diagnostic time required. Finally, the approaches are tabulated so as to provide a quick reference for NPC fault diagnostics. © 2022 by the authors.