Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Enhanced Power Density of Graphene Oxide–Phosphotetradecavanadate Nanohybrid for Supercapacitor Electrode(Springer, 2021) Maity, S.; Anandan Vannathan, A.A.; Kumar, K.; Das, P.P.; Mal, S.S.Successful exploration of supercapacitor (SC) material to integrate with high energy and high power density storage device still remains a daunting challenge. Conducting carbon nanostructures have been primarily used for this purpose; however, most of their surface area remains unutilized throughout the storage process. Herein, a new type of hybrid material has been reported by effectively using active sides of carbon nanostructures. Insertion of faradaic-type polyoxometalates (POMs), namely phosphotetradecavanadate (Na7[H2PV14O42], hereafter described as PV14), into the graphene oxide (GO) matrix creates a novel hybrid material for SC applications. Owing to the formation of nanohybrid, it can store charges both electrostatically and electrochemically. PV14/GO composite’s electrochemical behavior in different electrolyte (acidic/neutral) solutions shows different types of characteristics. The PV14/GO composite as a working electrode exhibits a high galvanostatic capacitance of 139 F/g while maintaining at a power density of 97.94 W/kg in 0.25 M H2SO4 electrolyte. The specific energy density was also found out to be around 56.58 Wh/kg at a 5 mV/s scan rate for the same electrolyte. Furthermore, in 1 M Na2SO4 solution, PV14/GO composite demonstrates a specific capacitance of 85.4 F/g at a scan rate of 5 mV/s. The equivalent series resistance for the device was found to be approximately 0.51 ? with a circuit resistance of 3.881 ?, using electrochemical impedance spectroscopy. The cell capacitance, employing the Nyquist plot, was calculated to be around 2.78 mF. © 2021, ASM International.Item Activated carbon- supported Vanado-nickelate (IV) based hybrid materials for energy application(Elsevier Ltd, 2021) Maity, S.; BM, N.; Kella, T.; Shee, D.; Das, P.P.; Mal, S.S.The rapid development of supercapacitor (SC) technology leads to increased demand for nanofabrication of novel and effective electroactive hybrid materials for next-generation energy storage devices. Herein, nickel tetradecavanadate, K2H5[NiV14O40](NiV14), is doped into porous activated carbon (AC), for the first time, in different wt.% in order to investigate the homogeneous loading of the inorganic metal-oxide component on the AC matrix. The resulting complex, AC-NiV14, is found to have possessed an enhanced electrochemical characteristic (for both symmetric and asymmetric SC cell), which operates at a significantly higher potential of 1.2 V. The combination of the double-layer capacitance (EDLC) and the redox-active polyoxometalate cluster leads to an intrinsic increase in specific capacitance (capacity) (from 45.3 Fg?1 (54.4 Cg?1) for AC to 316 Fg?1 (379.2 Cg?1) for 15 wt.% AC-NiV14 at a current density of 1 Ag?1). It was also observed that there is an increase of 20% in the operating voltage compared to conventional AC supercapacitors with acidic aqueous electrolytes. Firstly, symmetric supercapacitor's electrochemical performances of various wt.% of NiV14 composition were studied in acidic aqueous electrolyte (0.5 M H2SO4) solution. We observed that the 15 wt.% of AC-NiV14 hybrid electrode showed remarkable specific energy value (~63.2 Wh kg?1) compared with pristine AC and NiV14 electrodes, separately. Besides, the asymmetric layout (AC//AC-NiV14) increased the potential window up to 1.5 V and enhanced the specific energy and power values (90.1 Whkg?1 and 2400 Wkg?1, respectively), with 98% coulombic efficiency. Meanwhile, the AC-NiV14//NiV14 asymmetric cell possesses a specific capacitance (capacity) of 375 Fg?1 (450 Cg?1) with a maximum power of 3140 Wkg?1 at the high current density of 2 Ag?1. © 2021 Elsevier LtdItem Polyoxovanadate-Activated Carbon-Based Hybrid Materials for High-Performance Electrochemical Capacitors(Institute of Physics, 2022) Anandan Vannathan, A.; Chandewar, P.R.; Shee, D.; Mal, S.S.Two different polyoxovanadates derivatives, K5MnIVV11O32.10 H2O (MnV11) and K7MnIVV13O38.18 H2O (MnV13), have been studied to evaluate their electrochemical performance. These polyoxovanadates were deposited on activated carbon (AC) to prepare AC-MnV11 and AC-MnV13 composites. The electrochemical performance of the AC-MnV11 electrode exhibits the remarkable specific capacitance of 479.73 F g-1 at a current density of 0.6 A g-1, along with incredible specific power and energy of 960 W kg-1. Likewise, the AC-MnV13 exhibits a specific capacitance of 357.33 F g-1 at the current density of 0.6 A g-1 with a specific energy of 71.46 Wh kg-1. Interestingly, the AC-MnV11 could light up the red and yellow color LED bulbs for a duration of 80 and 60 s, respectively, indicating a considerable specific power of the material. The AC-MnV13 electrode shows significantly less lighting up during the 65 and 30 s period with red and yellow LED bulbs. © 2022 The Electrochemical Society ("ECS"). Published on behalf of ECS by IOP Publishing Limited.Item Phosphomolybdic acid embedded into biomass-derived biochar carbon electrode for supercapacitor applications(Elsevier B.V., 2023) J.e, M.; Chandewar, P.R.; Shee, D.; Mal, S.S.In high-performance, clean, safe, and cost-effective ways, supercapacitors are among the most promising ways to store and release nonfossil energy. In recent years, renewable biomass-derived activated carbon has been explored as a potential option for electrode material. It restricts their specific capacitance despite being environment-friendly and possessing intrinsic mechanical strength. In order to overcome this limitation and preserve all other properties, we are infusing polyoxometalate into the activated carbon; this increases specific capacitance with its fast reversible redox behaviour and preserves the carbon's characteristics. Beside suffusing phosphomolybdic acid (PMA) into biomass waste material, such as orange peel-derived activated carbon (OPAC), a new hybrid material (OPAC-PMA) was developed. The nanohybrid design was revealed by structural and morphological research, which showed high interfacial contact, allowing polyanions to redox rapidly. The novel hybrid electrode material (OPAC-PMA) has a capacitance value of 66% higher than the bare OPAC electrode. A further study showed that OPAC-PMA composite showed 88.23% cycle stability in 0.5 M H2SO4 electrolyte at 6 A g−1 for 4000 cycles. © 2023 Elsevier B.V.Item Waste dry cell derived photo-reduced graphene oxide and polyoxometalate composite for solid-state supercapacitor applications(Royal Society of Chemistry, 2023) Maity, S.; Biradar, B.R.; Srivastava, S.; Chandewar, P.R.; Shee, D.; Das, P.; Mal, S.S.In the modern era, realizing highly efficient supercapacitors (SCs) derived through green routes is paramount to reducing environmental impact. This study demonstrates ways to recycle and reuse used waste dry cell anodes to synthesize nanohybrid electrodes for SCs. Instead of contributing to landfill and the emission of toxic gas to the environment, dry cells are collected and converted into a resource for improved SC cells. The high performance of the electrode was achieved by exploiting battery-type polyoxometalate (POM) clusters infused on a reduced graphene oxide (rGO) surface. Polyoxometalate (K5[α-SiMo2VW9O40]) assisted in the precise bottom-up reduction of graphene oxide (GO) under UV irradiation at room temperature to produce vanadosilicate embedded photo-reduced graphene oxide (prGO-Mo2VW9O40). Additionally, a chemical reduction route for GO (crGO) was trialed to relate to the prGO, followed by the integration of a faradaic monolayer (crGO-Mo2VW9O40). Both composite frameworks exhibit unique hierarchical heterostructures that offer synergic effects between the dual components. As a result, the hybrid material's ion transport kinetics and electrical conductivity enhance the critical electrochemical process at the electrode's interface. The simple co-participation method delivers a remarkable specific capacity (capacitance) of 405 mA h g−1 (1622 F g−1) and 117 mA h g−1 (470 F g−1) for prGO-Mo2VW9O40 and crGO-Mo2VW9O40 nanocomposites alongside high capacitance retentions of 94.5% and 82%, respectively, at a current density of 0.3 A g−1. Furthermore, the asymmetric electrochromic supercapacitor crGO//crGO-Mo2VW9O40 was designed, manifesting a broad operating potential (1.2 V). Finally, the asymmetric electrode material resulted in an enhanced specific capacity, energy, and power of 276.8 C g−1, 46.16 W h kg−1, and 1195 W kg−1, respectively, at a current density of 0.5 A g−1. The electrode materials were tested in the operating of a DC motor. © 2023 The Royal Society of Chemistry.Item High-performance hybrid supercapacitor-immobilized Wells-Dawson polyoxometalates on activated carbon electrodes(Royal Society of Chemistry, 2023) Madhusree, J.E.; Chandewar, P.R.; Shee, D.; Mal, S.S.The nanofabrication of electroactive hybrid materials for next-generation energy storage devices is becoming increasingly significant as supercapacitor (SC) technology develops rapidly. The present study utilizes activated carbon (AC) templates reinforced with Wells-Dawson polyoxotungstates (POMs) to produce nanohybrid electrodes for high-performance supercapacitors. This study analyzes Wells-Dawson polyoxotungstates (P2W18) for the first time integrated with AC, and its structural and electrochemical performances are discussed. First, the electrochemical performances of symmetric supercapacitors were characterized in an acidic aqueous electrolyte (0.5 M H2SO4). It was observed that a supercapacitor cell containing the 5 wt% AC-P2W18 hybrid symmetric displayed a noteworthy specific capacitance of 289 F g−1 and a remarkable energy density of 40 W h kg−1. Moreover, 5% AC-P2W18 symmetric supercapacitor cells showed 89% cyclic stability over 4000 cycles. Three LED lights were charged onto the electrode. The LEDs continued to illuminate continuously for red until 160 seconds, yellow until 20 seconds, and blue until 10 seconds after removing the electrode from the electrochemical workstation, demonstrating the device's power and energy density. © 2023 The Royal Society of Chemistry.Item Pseudocapacitive effects of polyoxometalate implanted on graphene oxide matrix with polypyrrole for symmetric Supercapacitor applications(Elsevier B.V., 2024) Biradar, B.R.; Thathron, N.; Das, P.P.; Mal, S.S.Modern technological requirements emphasize designing and manufacturing electrochemical energy storage devices with high energy and power densities and longer cycle life. Supercapacitors with hybrid electrode materials have gained considerable attention as one of these systems due to their potential usage in futuristic applications such as electric vehicles and smart electric grids, among others. In this work, we synthesize potassium 9-tungsto-2-molybdo-1-vanadosilicate K5[α-SiMo2VW9O40]⋅10H2O and graphene oxide (GO) complex treating the latter as the supporting matrix for the former. We prepare the SiMo2VW9-polypyrrole (PPy) complex and then combine that with the GO matrix. The resulting nanohybrids GO-SiMo2VW9 and GO-PPy/SiMo2VW9 are found to have enhanced electrochemical properties when used in symmetric cells. Combining GO and pseudocapacitive materials can augment SC performance owing to their excellent redox properties. GO-SiMo2VW9 and GO-PPy/SiMo2VW9 showed 55.8 % and 85.5 % capacitive behavior at a scan rate of 10 mV/s, suggesting their use as high-performance pseudocapacitive materials as hybrid electrodes. GO-PPy/SiMo2VW9 electrode material shows a specific capacitance of 351.6 F/g with energy and power densities of 48.83 Wh/kg and 999.93 W/kg, respectively, at 0.5 A/g current density. Both the electrode materials yield capacitance retention of 60 % (GO-SiMo2VW9) and 80 % (GO-PPy/SiMo2VW9) after 5000 cycles at an 8A/g current density with almost 100 % coulombic efficiency, implying the stability of the electrode material. © 2024 Elsevier B.V.Item Carbon Nanotube-Supported Vanadium Substituted Phospho-Molybdate Nanohybrid for Supercapacitor Applications(John Wiley and Sons Inc, 2025) Biradar, B.R.; Swetha, M.T.; Thathron, N.; Puniyanikkottil, M.A.; Hanchate, A.; Das, P.P.; Mal, S.S.Owing to the depletion of conventional energy sources, our civilization is slowly transitioning to renewables. Therefore, designing effective energy storage systems is one of the most pressing technical demands. The quest for improved energy and power densities in energy storage devices, particularly those with long cycle life, has pushed the investigation of novel materials intended to build effective supercapacitors. In this work, nanohybrid materials are synthesized using a hydrothermal technique by mixing carbon nanotubes and a polyoxometalate cluster, H4[PVMo11O40].xH2O. Henceforth, this complex is acronymed as CNT-PVMo11. Further, electrochemical analysis of CNT-PVMo11 nanohybrid is carried out to examine various characteristics of the supercapacitor cell made with this nanohybrid. The cyclic voltammetry confirms the diffusive-dominant charge-storage process, quantifying a 72.83% diffusion mechanism at a scan rate of 1 mV s?1. The galvanostatic charge–discharge analysis of CNT-PVMo11 nanohybrid material showed a specific capacitance of 229.35 F g?1 with energy and power densities of 31.85 Wh kg?1 and 2000 W kg?1, respectively, at 1 A g?1 current density. The electrode material also shows 90% capacitance retention even after 6000 cycles at 8 A g?1 current density, indicating the material's remarkable stability. The high specific capacitance, excellent energy density, and impressive cycling stability of the hybrid material make it a promising candidate for next-generation supercapacitor electrodes. © 2025 Wiley-VCH GmbH.