Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Improved electrochemical performance of graphene oxide supported vanadomanganate (IV) nanohybrid electrode material for supercapacitors(Elsevier Ltd, 2020) Kumari, S.; Maity, S.; Anandan Vannathan, A.A.; Shee, D.; Das, P.P.; Mal, S.S.Graphene oxide (GO)-supported polyoxometalates (POMs) have been considered as promising electrode materials for energy storage applications due to their ability to undergo fast and reversible redox reactions. Herein, vanadomanganate-GO composites (K7MnIVV13O38.18H2O-GO with 2:1 and 4:1 ratio) were investigated for use as potential electrode materials in supercapacitors (SCs). The K7MnIVV13O38.18H2O (MnV13) was synthesized and anchored on GO through electron transfer interaction and electrostatic interaction to make the composite electrodes for the present study. All synthesized electrode materials were fully characterized by various techniques, e.g., Fourier Transform Infrared (FTIR) Spectroscopy, Powder X-ray Diffraction (XRD), Scanning Electron Microscopy/Energy Dispersive X-ray Spectroscopy (SEM/EDS) and High Resolution-Transmission Electron Microscopy (HR-TEM). The electrochemical properties of MnV13/GO composites with different MnV13/GO ratios were investigated by two-electrode cyclic voltammetry (CV) and galvanostatic charge/discharge (GCD) in different electrolytes. The MnV13/GO composite of ratio 2:1 in 1 M LiCl electrolyte and that of ratio 4:1 in 1 M Na2SO4 electrolyte showed significant specific capacitance values of 269.15 F/g and 387.02 F/g, respectively and energy density of 37.38 Wh/kg and 53.75 Wh/kg, respectively for a scan rate of 5 mV/s. Interestingly, the 1:1 (MnV13/GO) composite in 1 M Na2SO4 and 1 M LiCl electrolytes showed very low specific capacitance values as the deposition of MnV13 on GO was not sufficient, as indicated by FTIR and SEM. Thus, it is evident that the specific capacitance value of these composite materials depends on the amount of MnV13 deposited on GO and these composite materials exhibit the potential to improve the performance of GO-based SCs. © 2019Item Imidazolium cation linkers of polyoxomolybdate-polypyrrole nanocomposite electrode-based energy storage supercapacitors(Elsevier Ltd, 2022) Muhammed Anees, P.K.; Anandan Vannathan, A.A.; Abhijith, M.B.; Kella, T.; Shee, D.; Mal, S.S.The electrochemical properties of a new hybrid electrode, liquid-polyoxometalate-polypyrrole (BMIM-PVMo11-PPy) have been studied. The H4[PVMo11O40] (PVMo11) was combined with 1-Butyl-3-methyl-imidazolium (BMIM) ionic liquid and then doped on the polypyrrole (PPy) surface. In order to investigate the interaction between the BMIM, PVMo11, and PPy compound was characterized using various analytical techniques, such as Infrared spectroscopy, thermal stability analysis, powder X-ray diffraction, multinuclear NMR (1H and 13C), FESEM, EDX, and surface adsorption studies. The electrochemical performance of the BMIM-PVMo11-PPy composite material has been tested in an aqueous 0.25 M H2SO4 electrolytic solution. The BMIM-PVMo11-PPy composite exhibits the highest specific capacitance of 527.39 F g−1 at a current density of 1 A g−1, along with remarkable specific energy and power of 51.07 Wh kg−1 and 1078.96 W kg−1, respectively. The BMIM-PVMo11-PPy composite was observed to light up red and blue color LED bulbs for 66 and 16 s, respectively, with 84 mg of sample coated on carbon cloth, suggesting an incredible specific power of that material. © 2021 Elsevier B.V.Item Investigations of redox-active polyoxomolybdate embedded polyaniline-based electrode material for energy application(Springer Science and Business Media Deutschland GmbH, 2022) Anandan Vannathan, A.A.; Kella, T.; Shee, D.; Mal, S.S.Higher capacitance supercapacitors have received considerable attention, including their massive power density, high stability, and long cycle life. On the other hand, polymers have been known for their energy storage device application because of the pseudocapacitance behavior resulting from the extended conjugation over the polymer backbone. Here, we report a simple chemical bath deposition method for the synthesis of two polyoxometalates (H4[PVMo11O40] and H5[PV2Mo10O40]) impregnated polyaniline (PAni) composite (PVMo11@PAni and PV2Mo10@PAni) for electrochemical supercapacitors. Various analytical methods characterized the electrode materials, e.g., Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), powder X-ray diffraction (PXRD) method, and the morphological features of those electrodes were acquired by field emission scanning microscopy (FESEM). The exceptionally high average capacitance of 1371 F g−1 was obtained for the composite PVMo11@PAni electrode at a 3 A g−1 current density and 1 V potential window with an energy density of 137.5 W h kg−1. The PVMo11@PAni composite electrode showed almost 4.3 times the higher energy density than pure PAni and 2.3 times higher than PV2Mo10@PAni. In contrast, PV2Mo10@PAni composite showed 1.9 times more energy density than pure PAni composite electrode. Interestingly, high average capacitance, charge–discharge rates, and high energy density with high-level power delivery make them promising electrode candidates for supercapacitors. © 2021, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.Item Vanadomanganate as a synergistic component in high-performance symmetric supercapacitor(Elsevier Ltd, 2022) Maity, S.; Anandan Vannathan, A.A.; Chandewar, P.R.; Shee, D.; Das, P.P.; Mal, S.S.Supercapacitor devices fabricated from capacitive and battery-type hybrid electrodes have been projected as a promising energy storage system because of their ability to produce high specific power and energy simultaneously. In this work, we have demonstrated a facile method of impregnation of faradaic type manganese (III) polyoxovanadate, [MnV14O40]−6 on the high surface area substrate of activated carbon (AC) as well as graphene oxide (GO). Materials and electrochemical characterizations data confirm the successful incorporation of capacitive and faradaic type manganese (III) polyoxovanadate into the nanohybrid electrode material. Furthermore, the synergic effect between the carbonaceous nanostructures (AC/GO) and redox-active oxometalate (MnV14) provides a better pathway for ion transport to the interface resulting in enhancement of the conductivity, diffusion ability of the nanohybrid. Moreover, the battery-type MnV14 clusters disperse in the micro/mesopores of AC, whereas the oxygen-containing functional groups in GO act as active sites for anchoring of MnV14 clusters. Thus, the surface modification with MnV14 clusters enhances the specific capacitance of nanohybrid with remarkable electrical and mechanical stability. The AC/MnV14 nanohybrid exhibits an enhanced specific capacitance of 547 F g−1 with specific energy and power of 76 Wh kg−1 and 1600 W kg−1, respectively, at 0.8 A g−1 current density. Additionally, GO/MnV14 shows a specific capacitance of 330 F g−1 with improved specific energy and power of 30 Wh kg−1 and 1276 W kg−1, respectively, at the same current density. Moreover, both the nanohybrids possess excellent cycle stability by retaining 92% (AC/MnV14) and 90.6% (GO/MnV14) of initial capacitance even after 5000 sweeping cycles. © 2021 Elsevier B.V.Item Polyoxovanadate-Activated Carbon-Based Hybrid Materials for High-Performance Electrochemical Capacitors(Institute of Physics, 2022) Anandan Vannathan, A.; Chandewar, P.R.; Shee, D.; Mal, S.S.Two different polyoxovanadates derivatives, K5MnIVV11O32.10 H2O (MnV11) and K7MnIVV13O38.18 H2O (MnV13), have been studied to evaluate their electrochemical performance. These polyoxovanadates were deposited on activated carbon (AC) to prepare AC-MnV11 and AC-MnV13 composites. The electrochemical performance of the AC-MnV11 electrode exhibits the remarkable specific capacitance of 479.73 F g-1 at a current density of 0.6 A g-1, along with incredible specific power and energy of 960 W kg-1. Likewise, the AC-MnV13 exhibits a specific capacitance of 357.33 F g-1 at the current density of 0.6 A g-1 with a specific energy of 71.46 Wh kg-1. Interestingly, the AC-MnV11 could light up the red and yellow color LED bulbs for a duration of 80 and 60 s, respectively, indicating a considerable specific power of the material. The AC-MnV13 electrode shows significantly less lighting up during the 65 and 30 s period with red and yellow LED bulbs. © 2022 The Electrochemical Society ("ECS"). Published on behalf of ECS by IOP Publishing Limited.Item Phosphomolybdic acid embedded into biomass-derived biochar carbon electrode for supercapacitor applications(Elsevier B.V., 2023) J.e, M.; Chandewar, P.R.; Shee, D.; Mal, S.S.In high-performance, clean, safe, and cost-effective ways, supercapacitors are among the most promising ways to store and release nonfossil energy. In recent years, renewable biomass-derived activated carbon has been explored as a potential option for electrode material. It restricts their specific capacitance despite being environment-friendly and possessing intrinsic mechanical strength. In order to overcome this limitation and preserve all other properties, we are infusing polyoxometalate into the activated carbon; this increases specific capacitance with its fast reversible redox behaviour and preserves the carbon's characteristics. Beside suffusing phosphomolybdic acid (PMA) into biomass waste material, such as orange peel-derived activated carbon (OPAC), a new hybrid material (OPAC-PMA) was developed. The nanohybrid design was revealed by structural and morphological research, which showed high interfacial contact, allowing polyanions to redox rapidly. The novel hybrid electrode material (OPAC-PMA) has a capacitance value of 66% higher than the bare OPAC electrode. A further study showed that OPAC-PMA composite showed 88.23% cycle stability in 0.5 M H2SO4 electrolyte at 6 A g−1 for 4000 cycles. © 2023 Elsevier B.V.Item Waste dry cell derived photo-reduced graphene oxide and polyoxometalate composite for solid-state supercapacitor applications(Royal Society of Chemistry, 2023) Maity, S.; Biradar, B.R.; Srivastava, S.; Chandewar, P.R.; Shee, D.; Das, P.; Mal, S.S.In the modern era, realizing highly efficient supercapacitors (SCs) derived through green routes is paramount to reducing environmental impact. This study demonstrates ways to recycle and reuse used waste dry cell anodes to synthesize nanohybrid electrodes for SCs. Instead of contributing to landfill and the emission of toxic gas to the environment, dry cells are collected and converted into a resource for improved SC cells. The high performance of the electrode was achieved by exploiting battery-type polyoxometalate (POM) clusters infused on a reduced graphene oxide (rGO) surface. Polyoxometalate (K5[α-SiMo2VW9O40]) assisted in the precise bottom-up reduction of graphene oxide (GO) under UV irradiation at room temperature to produce vanadosilicate embedded photo-reduced graphene oxide (prGO-Mo2VW9O40). Additionally, a chemical reduction route for GO (crGO) was trialed to relate to the prGO, followed by the integration of a faradaic monolayer (crGO-Mo2VW9O40). Both composite frameworks exhibit unique hierarchical heterostructures that offer synergic effects between the dual components. As a result, the hybrid material's ion transport kinetics and electrical conductivity enhance the critical electrochemical process at the electrode's interface. The simple co-participation method delivers a remarkable specific capacity (capacitance) of 405 mA h g−1 (1622 F g−1) and 117 mA h g−1 (470 F g−1) for prGO-Mo2VW9O40 and crGO-Mo2VW9O40 nanocomposites alongside high capacitance retentions of 94.5% and 82%, respectively, at a current density of 0.3 A g−1. Furthermore, the asymmetric electrochromic supercapacitor crGO//crGO-Mo2VW9O40 was designed, manifesting a broad operating potential (1.2 V). Finally, the asymmetric electrode material resulted in an enhanced specific capacity, energy, and power of 276.8 C g−1, 46.16 W h kg−1, and 1195 W kg−1, respectively, at a current density of 0.5 A g−1. The electrode materials were tested in the operating of a DC motor. © 2023 The Royal Society of Chemistry.Item High-performance hybrid supercapacitor-immobilized Wells-Dawson polyoxometalates on activated carbon electrodes(Royal Society of Chemistry, 2023) Madhusree, J.E.; Chandewar, P.R.; Shee, D.; Mal, S.S.The nanofabrication of electroactive hybrid materials for next-generation energy storage devices is becoming increasingly significant as supercapacitor (SC) technology develops rapidly. The present study utilizes activated carbon (AC) templates reinforced with Wells-Dawson polyoxotungstates (POMs) to produce nanohybrid electrodes for high-performance supercapacitors. This study analyzes Wells-Dawson polyoxotungstates (P2W18) for the first time integrated with AC, and its structural and electrochemical performances are discussed. First, the electrochemical performances of symmetric supercapacitors were characterized in an acidic aqueous electrolyte (0.5 M H2SO4). It was observed that a supercapacitor cell containing the 5 wt% AC-P2W18 hybrid symmetric displayed a noteworthy specific capacitance of 289 F g−1 and a remarkable energy density of 40 W h kg−1. Moreover, 5% AC-P2W18 symmetric supercapacitor cells showed 89% cyclic stability over 4000 cycles. Three LED lights were charged onto the electrode. The LEDs continued to illuminate continuously for red until 160 seconds, yellow until 20 seconds, and blue until 10 seconds after removing the electrode from the electrochemical workstation, demonstrating the device's power and energy density. © 2023 The Royal Society of Chemistry.Item Fabrication of supercapacitor electrode material using carbon derived from waste printer cartridge(Springer Science and Business Media Deutschland GmbH, 2024) Biradar, B.R.; Maity, S.; Chandewar, P.R.; Shee, D.; Das, P.P.; Mal, S.S.Transforming recyclable materials into a suitable product is an important area of research nowadays. This report demonstrates that carbon material derived from waste printer cartridges can be exploited to fabricate electrochemical cells—particularly supercapacitors (SCs). SCs are electrochemical energy storage devices currently attracting much attention in the research community due to their salient features, such as cost-effectiveness, extended cycle stability, and durability. Here, we report the results of thoroughly examining the effects of acidic, basic, and neutral aqueous electrolytes on printer waste carbon electrode material in SC efficiency. In our work, the waste carbon collected from used printer cartridges shows a specific capacitance of 178.4 F/g with energy and power density of 24.77 Wh/kg and 999.68 W/kg, respectively, at 0.5 A/g current density in acidic (1 M H2SO4) electrolyte medium. Moreover, it exhibited very promising capacitance of 135.04 F/g and 87.04 F/g in basic (1 M LiOH) and neutral (1 M NaCl) electrolyte medium, respectively, at 0.8 A/g current density with considerably better cycle stability. In an acidic medium, printer waste carbon drives a DC motor for 1 min with a three-cell series arrangement. The properties of that waste carbon (extracted from the cartridges) are similar to high-rate activated carbon available commercially. Graphical Abstract: (Figure presented.). © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2024.Item Carbon Nanotube-Supported Vanadium Substituted Phospho-Molybdate Nanohybrid for Supercapacitor Applications(John Wiley and Sons Inc, 2025) Biradar, B.R.; Swetha, M.T.; Thathron, N.; Puniyanikkottil, M.A.; Hanchate, A.; Das, P.P.; Mal, S.S.Owing to the depletion of conventional energy sources, our civilization is slowly transitioning to renewables. Therefore, designing effective energy storage systems is one of the most pressing technical demands. The quest for improved energy and power densities in energy storage devices, particularly those with long cycle life, has pushed the investigation of novel materials intended to build effective supercapacitors. In this work, nanohybrid materials are synthesized using a hydrothermal technique by mixing carbon nanotubes and a polyoxometalate cluster, H4[PVMo11O40].xH2O. Henceforth, this complex is acronymed as CNT-PVMo11. Further, electrochemical analysis of CNT-PVMo11 nanohybrid is carried out to examine various characteristics of the supercapacitor cell made with this nanohybrid. The cyclic voltammetry confirms the diffusive-dominant charge-storage process, quantifying a 72.83% diffusion mechanism at a scan rate of 1 mV s?1. The galvanostatic charge–discharge analysis of CNT-PVMo11 nanohybrid material showed a specific capacitance of 229.35 F g?1 with energy and power densities of 31.85 Wh kg?1 and 2000 W kg?1, respectively, at 1 A g?1 current density. The electrode material also shows 90% capacitance retention even after 6000 cycles at 8 A g?1 current density, indicating the material's remarkable stability. The high specific capacitance, excellent energy density, and impressive cycling stability of the hybrid material make it a promising candidate for next-generation supercapacitor electrodes. © 2025 Wiley-VCH GmbH.