Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Lamani, V.T.Subject: search.filters.subject.Diesel engines

Search Results

Now showing 1 - 5 of 5
  • No Thumbnail Available
    Item
    Combustion, performance, and tail pipe emissions of common rail diesel engine fueled with waste plastic oil-diesel blends
    (American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2018) Lamani, V.T.; Yadav, A.K.; Kumar, G.N.
    The demand for plastic is eternally growing in urban areas and producing enormous quantity of plastic waste. The management and disposal of plastic waste have become a major concern worldwide. The awareness of waste to energy retrieval is one of the promising modes used for the treatment of the waste plastic. The present investigation evaluates the prospective use of waste plastic oil (WPO) as an alternative fuel for diesel engine. Different blends (WPO0, WPO30, and WPO50) with diesel are prepared on a volume basis and the engine is operated. Experiments are conducted for various injection timings (9 deg, 12 deg, 15 deg, and 18 deg BTDC) and for different exhaust gas recirculation (EGR) rates (0%, 10%, 15%, and 20%) at 100 MPa injection pressure. Combustion, performance, and tail pipe emissions of common rail direct injection (CRDI) engine are studied. The NOx, CO, and Soot emissions for waste plastic oil-diesel blends are found more than neat diesel. To reduce the NOx, EGR is employed, which results in reduction of NOx considerably, whereas other emissions, i.e., CO and Soot, get increased with increase in EGR rates. Soot for WPO-diesel blends is higher because of aromatic compounds present in plastic oils. Brake thermal efficiency (BTE) of blends is found to be higher compared to diesel. © 2018 by ASME.
  • No Thumbnail Available
    Item
    NOx reduction studies on a diesel engine operating on waste plastic oil blend using selective catalytic reduction technique
    (Elsevier B.V., 2019) Ayodhya, A.S.; Lamani, V.T.; Thirumoorthy, M.; Kumar, G.N.
    The constant escalation in the consumption of petroleum products has compelled researchers to discover for new alternative fuels which can be successfully incorporated in the existing automotive engines. Oil derived from waste plastics is one such alternative, which not only ensures longevity of fossil fuels but also assists in bringing down the hazardous impacts caused by the improper disposal of plastic wastes. This work focuses on the utilization of valuable energy of toxic non-biodegradable waste plastics to lucratively be used as an alternative fuel. An attempt was further made to reduce the NO X emissions which increased with the use of waste plastic oil blend. The main objective of this experimental investigation is to study the performance & emission characteristics of a twin cylinder CRDI engine subjected to selective catalytic reduction (SCR) after-treatment technique. Different flow rates of ammonia as a reducing agent were tested and concluded that a flow rate of 0.5 kg/hr furnishes optimum results. A comparison of NO X reduction efficiency was also made between SCR and EGR techniques. The comparison eventually indicated that SCR gives better NO X conversion efficiency at higher loads without any adverse effect on the engine performance while operating on Waste Plastic Oil blend (P30). © 2018 Energy Institute
  • No Thumbnail Available
    Item
    Effect of bioethanol–diesel blends, exhaust gas recirculation rate and injection timing on performance, emission and combustion characteristics of a common rail diesel engine
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Lamani, V.T.; Baliga M, A.U.; Yadav, A.K.; Kumar, G.N.
    This investigation is focused on the effect of exhaust gas recirculation (EGR) and injection timing on the performance, combustion and exhaust emission characteristics of common rail direct injection (CRDI) engine fueled with bioethanol-blended diesel using computational fluid dynamics (CFD) simulation. Simulation is carried out for various EGR rates (0, 10, 20 and 30%), two different injection timings, and two different bioethanol–diesel blends (10 and 20%) at injection pressure. The equivalence ratio is kept constant in all the cases of bioethanol–diesel blends. The results indicate that the mean CO formation and ignition delay increase, whereas mean NO formation and in-cylinder temperature decrease, with increase in the EGR rate. Further, with an increase in percentage of the bioethanol blends, CO and soot formation decrease as compared to neat diesel. A significant increase in in-cylinder pressure (15%) is found at 14° before top dead centre (BTDC) compared to 9° BTDC, which leads to an increase in indicated thermal efficiency of 4% for neat diesel at 30% EGR. In the present study, maximum indicated thermal efficiency is obtained in the case of 10 and 20% bioethanol–diesel blend, and remains constant for all EGR rates considered in the study. Obtained results are validated with the available literature data and indicate good agreement. © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Effect of exhaust gas recirculation rate on performance, emission and combustion characteristics of a common-rail diesel engine fuelled with n-butanol–diesel blends
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2020) Lamani, V.T.; Yadav, A.; Gottekere, K.N.
    Increasing fears of fossil fuel attenuation and tough emission protocols compel the research community to explore alternative renewable fuels for diesel engines. Butanol is desirable among renewable fuels due to its properties favorable to diesel engines. This study focused on the suitability of exhaust gas recirculation (EGR) and optimum injection timing on the performance, combustion and exhaust emission characteristics of common-rail direct-injection (CRDI) engine fueled with n-butanol-blended diesel using experimental and computational fluid dynamics (CFD) simulation. Various EGR rates and injection timings are considered for different butanol–diesel blends (0, 10, 20 and 30%). Obtained simulation results are validated with experimental data and found to be in good agreement. For all EGR rates and blends, nitrogen oxide (NO) emission is reduced drastically, whereas carbon monoxide (CO) and soot emissions are decreased moderately, with increase in n-butanol–diesel blends. The CO and soot emissions increase with EGR rate due to oxygen deficiency as well. Brake thermal efficiency is reduced by approximately 1% for neat diesel (Bu0) with increase in EGR rates. Soot emission for Bu30 (15 ° Before top dead centre (BTDC) is decreased by 23, 25, 24 and 26% for 0, 10, 20 and 30% EGR rates, respectively, compared to Bu0 (12° BTDC). © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Computational fluid dynamic analysis of the effect of inlet valve closing timing on common rail diesel engines fueled with butanol–diesel blends
    (Frontiers Media SA, 2024) Lamani, V.T.; Shivaprasad, K.V.; Roy, D.; Yadav, A.K.; Kumar, G.N.
    The inlet valve closing (IVC) timing plays a crucial role in engine combustion, which impacts engine performance and emissions. This study attempts to measure the potential to use n-butanol (Bu) and its blends with the neat diesel in a common rail direct injection (CRDI) engine. The computational fluid dynamics (CFD) simulation is carried out to estimate the performance, combustion, and exhaust emission characteristics of n-butanol–diesel blends (0%–30% by volume) for variable valve timings. An experimental study is carried out using standard valve timing and blends to validate the CFD model (ESE AVL FIRE). After validation, the CFD model is employed to study the effect of variable valve timings for different n-butanol–diesel blends. Extended coherent flame model-3 zone (ECFM-3Z) is implemented to conduct combustion analysis, and the kappa–zeta–f (k–ζ–f) model is employed for turbulence modeling. The inlet valve closing (IVC) time is varied (advanced and retarded) from standard conditions, and optimized valve timing is obtained. Advancing IVC time leads to lower cylinder pressure during compression due to reduced trapped air mass. The brake thermal efficiency (BTE) is increased by 4.5%, 6%, and 8% for Bu10, Bu20, and Bu30, respectively, compared to Bu0. Based on BTE, optimum injection timings are obtained at 12° before the top dead center (BTDC) for Bu0 and 15° BTDC for Bu10, Bu20, and Bu30. Nitrogen oxide (NOx) emissions increase due to complete combustion. Due to IVC timing, further carbon monoxide and soot formation decreased with blends and had an insignificant effect. © © 2024 Lamani, Shivaprasad, Roy, Yadav and Kumar.