Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Evaluation of optimal parameters of MR fluids for damper application using particle swarm and response surface optimisation(Springer Verlag service@springer.de, 2017) Gurubasavaraju, T.M.; Kumar, H.; Mahalingam, A.The controllable rheological properties of MR fluid exhibit viscoelastic properties within pre-yield, which are essential for the characterization of MR dampers for the isolation of vibration. In the present work, using particle swarm optimisation (PSO), it is identified that the proportion of MR fluid constituents, fluid gap and current are the parameters which influence majorly on the rheological properties and damping effect of MR damper. Initially, rheological properties of the prepared MR fluid samples are determined using rotational plate–plate type rheometer with the magnetorheological device cell attachment by keeping three levels of gap between the parallel plates. Three different proportions of MR fluid are prepared based on the volume fraction of carbonyl iron particle, i.e., 25, 30 and 35% in the silicone carrier fluid along with 1% of lithium-based grease as stabiliser. The objective function of this optimisation problem is to maximise the shear stress and damping force of the MR damper. The design of experiment (DOE) is employed to obtain the various combinations of parameters and their respective responses. The interaction of the regression model obtained from the DOE is used in PSO to evaluate the optimal parameters. The results indicated that the MR fluid with the particle concentration of 31% is the optimal proportion for MR damper application. © 2017, The Brazilian Society of Mechanical Sciences and Engineering.Item Semi-active vibration control of SiC-reinforced Al6082 metal matrix composite sandwich beam with magnetorheological fluid core(SAGE Publications Ltd info@sagepub.co.uk, 2020) Allien, J.V.; Kumar, H.; Desai, V.Dynamic characterization of silicon carbide particles reinforced Al6082 alloy metal matrix composite sandwich beam with magnetorheological fluid core is experimentally investigated. The study is focused on determining the effect of magnetorheological fluid core on the dynamic behavior of the sandwich structure. The magnetorheological fluid core is enclosed between the top and bottom metal matrix composite beams. The metal matrix composite beams are cast with silicon carbide particles in Al6082 alloy varying from 0 to 20 wt%. The magnetorheological fluid is prepared in-house and contains 30 vol.% carbonyl iron powder and 70 vol.% silicone oil. The free vibration test is conducted to determine the natural frequencies and damping ratio. It is found that the natural frequencies and damping ratio of the sandwich beams increased with an increase in the applied magnetic flux density. The experimental forced dynamic response of sandwich beams is carried out using sine sweep excitation. Vibration amplitude suppression capabilities of the sandwich beams subjected to varying magnetic flux densities are determined. The experimental forced vibration results reveal that metal matrix composite–magnetorheological fluid core sandwich beams have excellent vibration amplitude suppression capabilities. © IMechE 2019.Item Semi-active vibration control of MRF core PMC cantilever sandwich beams: Experimental study(SAGE Publications Ltd info@sagepub.co.uk, 2020) Allien, J.V.; Kumar, H.; Desai, V.The semi-active vibration control of sandwich beams made of chopped strand mat glass fiber reinforced polyester resin polymer matrix composite (PMC) and magnetorheological fluid (MRF) core were experimentally investigated in this study. Two-, four- and six-layered glass fiber reinforced polyester resin polymer matrix composites were prepared using the hand-layup technique. The magnetorheological fluid was prepared in-house with 30% volume of carbonyl iron powder and 70% volume of silicone oil. Nine cantilever sandwich beams of varying thicknesses of the top and bottom layers glass fiber reinforced polyester resin polymer matrix composite beams and middle magnetorheological fluid core were prepared. The magnetorheological fluid core was activated with a non-homogeneous magnetic field using permanent magnets. The first three modes, natural frequencies and damping ratios of the glass fiber reinforced polyester resin polymer matrix composite-magnetorheological fluid core sandwich beams were determined through free vibration analysis using DEWESoft modal analysis software. The amplitude frequency response of the glass fiber reinforced polyester resin polymer matrix composite-magnetorheological fluid core sandwich beams through forced vibration analysis was determined using LabVIEW. The effect of various parameters such as magnetic flux density, thickness of glass fiber reinforced polyester resin polymer matrix composite layers and magnetorheological fluid core layer on the natural frequencies, damping ratio and vibration amplitude suppressions of the glass fiber reinforced polyester resin polymer matrix composite-magnetorheological fluid core sandwich beams was investigated. Based on the results obtained, 2 mm thickness top and bottom layers glass fiber reinforced polyester resin polymer matrix composite and 5 mm thickness magnetorheological fluid core sample have achieved a high shift in increased natural frequency, damping ratio and vibration amplitude suppression under the influence of magnetic flux density. © IMechE 2020.Item Influence of different fumed silica as thixotropic additive on carbonyl particles magnetorheological fluids for sedimentation effects(Elsevier B.V., 2021) Aruna, M.N.; Rahman, M.R.; Joladarashi, S.; Kumar, H.; Bhat Panemangalore, D.B.The present work reports the influence of different types of surface area, hydrophobic, and hydrophilic fumed silica mixed in silicone oil as a thixotropic additive on carbonyl particles based magnetorheological fluids (MRFs) were prepared. Scanning electron microscopy analysis confirms the fumed silica particles attached to the surfaces of CIPs. The vibrating sample magnetometer result shows the MRF4 and 5 have a better magnetic saturation value of 30.12 emu/gm and 40.12 emu/gm, respectively. The experimental rheological flow curve behaviours are investigated using the magnetorheometer. The Herschel–Bulkley rheological model is found to be in good agreement with the experimental curves and suggested shear thinning property is observed. The results showed that the hydrophilic silica with larger surface area type presented (i.e.MRF 4 and 5) better magnetorheological fluid characteristics in terms of shear stress, with a high value of dynamic yield stress, and have much-improved sedimentation ratio up to seven days. © 2021 Elsevier B.V.Item Effect of temperature on sedimentation stability and flow characteristics of magnetorheological fluids with damper as the performance analyser(Elsevier B.V., 2022) Kumar Kariganaur, A.; Kumar, H.; Arun, M.dimentation stability and high yield stress of a magnetorheological fluid (MRFs) are essential parameters for better damping performance for any practical application. Preliminary investigations have been carried out on carbonyl iron particles to determine the morphology, particle size, crystal structure, and saturation magnetization for their feasibility of synthesizing magnetorheological fluids in-house. This study synthesizes various MRFs from various commonly used carrier oils and additives. The MRF samples were prepared for 25% volume fractions of carbonyl iron (CI) powder in either silicone oil (350cSt) or hydraulic oil (50cSt) and by using lithium and calcium-based additives or a combination of both the additives. The sedimentation stability and yield behaviour at different temperatures show a remarkable drop in sedimentation rate and yield stress for all the MR fluid samples. The characterization of the prepared MR fluids reveals that MRF-1, MRF-3, MRF-5 are more stable and have high yield stress values. MRF-1 is selected to further characterize its dynamic performance in magnetorheological damper fabricated based on geometric dimensions obtained from the response surface optimization technique. The results indicate a 164.45% and 135.48% increase in damping force at higher amplitude and higher frequencies at 0A and 1A currents. Further, similar tests have been carried out by synthesizing MRF-7 with silicone oil (50cSt) + lithium base grease as the additive. The sample's stability and yield stress with temperature are carried out, and performance analysis shows a remarkable change in damping force than MRF-1. The dynamic range obtained is practically viable in MRF-7 than MRF-1, with less variability. Finally, temperature characteristics captured from the thermocouple of the MR damper reveal that an average of 43.78% reduction in damping force when the temperature is increased by 19.5 °C with increased dynamic range. © 2022 Elsevier B.V.Item Rheological Properties of the In-house Prepared Magneto-rheological Fluid in the Pre-yield Region(Materials and Energy Research Center, 2022) Nagiredla, S.; Joladarashi, S.; Kumar, H.The essence of the present work is to study the rheological properties of the in-house prepared magnetorheological (MR) fluids in the pre-yield region since the rheological properties play a vital role in better understanding of vibration damping capabilities of MR fluids. In the present work, two different compositions of MR fluid samples were prepared with 24 and 30 volume percentages of carbonyl iron (CI) particles. Prepared MR fluid samples contain CI particles as a dispersive medium, silicone oil as a carrier fluid and white lithium grease as an anti-settling agent. The oscillating driving frequency and amplitude strain sweep tests are performed to investigate the rheological properties within the pre-yield region. The influences of driving frequency, strain amplitude, magnetic field and CI particles volume percentage on the rheological properties of the prepared MR fluids were assessed. The linear viscoelastic region of the prepared MR fluid sample was identified and the yield strain obtained was around 0.371%. It is observed that the volume percentage of CI particles in the MR fluid strongly influenced the rheological properties. © 2022 Materials and Energy Research Center. All rights reserved.Item Characterization of an in-house prepared magnetorheological fluid and vibrational behavior of composite sandwich beam with magnetorheological fluid core(Sharif University of Technology, 2023) Nagiredla, S.; Joladarashi, S.; Kumar, H.In this research work, two different compositions of MR fluid samples with 24 and 30 percentage (%) volume fraction of carbonyl iron (CI) particles are prepared. Prepared MR fluid (MRF) samples contain carbonyl iron particles as a dispersive medium, silicone oil as a carrier fluid, and white lithium grease as an anti-settling agent. Influence of oscillating driving frequency, strain amplitude, magnetic field, and the percentage of CI particle on the rheological properties of the MR fluid samples are presented. Storage modulus and loss factor equations are estimated from the rheometry results using a linear regression method. The properties of MR fluid samples are taken to design and model the sandwich beams using ANSYS ACP software, where carbon epoxy composite material is used as the face layer and MR fluid as the core material. Modal, harmonic, and transient analysis studies have been conducted on all the modelled sandwich beams. Influence of MR fluid core material thickness, face layer thickness, CI particle volume percentage in the prepared MR fluid sample, and magnetic field on the vibrational response of the sandwich beams have been presented. Carbon-epoxy composites with an in-house made MRF sandwich beam has shown some significant results in the vibrational response. © 2023 Sharif University of Technology. All rights reserved.