Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Kumar, G.N.Subject: search.filters.subject.Performance and emissions

Search Results

Now showing 1 - 10 of 12
  • No Thumbnail Available
    Item
    Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends
    (Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.
    This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.
  • No Thumbnail Available
    Item
    Effect of hydrogen addition on the performance and emission parameters of an SI engine fueled with butanol blends at stoichiometric conditions
    (Elsevier Ltd, 2015) Raviteja, S.; Kumar, G.N.
    Hydrogen is considered as the best fuel due to its excellent combustion properties. But its use as a fuel is confined by its low energy density. In the present investigation an attempt has been made to utilize some of the benefits of hydrogen by using it as an additive in a butanol fueled engine. The experimental study has been carried out on a 4 stroke, single cylinder, manifold electronic fuel injected (EFI) engine mapped to run at stoichiometric conditions. Butanol blends were chosen as the base fuel due to their higher energy density compared to ethanol. A small fraction of hydrogen was injected into the air stream. The engine was run at 3000 RPM at full load condition. The performance, emission and combustion parameters are compared for four concentrations of butanol (10%, 20%, 30%, and 100% by volume of fuel) and two concentrations of hydrogen (5%, and 10% by volume of air) with gasoline. The results indicated that the efficiency of the engine improved upon hydrogen enrichment. An average of 60% reduction was observed in HC and CO emissions with 10% enrichment of hydrogen, whereas the NO emissions almost doubled itself. The combustion analysis showed reduced delay periods, shorter combustion durations, higher cylinder pressures, higher temperatures and improved combustion. © 2015 Hydrogen Energy Publications, LLC.
  • No Thumbnail Available
    Item
    Experimental Investigation of Variations in Spark Timing using a Spark-Ignition Engine with Hydrogen-Blended Gasoline
    (Wiley-VCH Verlag info@wiley-vch.de, 2015) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.
    This study describes an experiment conducted using an electronically controllable single-cylinder high-speed gasoline engine to analyze the performance and emissions characteristics of various hydrogen-gasoline blends. The experiments have been conducted for various engine speeds and spark timings at the wide open throttle position. The experimental results revealed that the engine brake thermal efficiency and brake mean effective pressure first increase and then decrease with the increase engine speed at all spark timings. The minimum amount of brake specific energy consumption was observed for 20% hydrogen addition in the total fuel blend at 3000rpm engine speed and 14°crank angle (CA) before top dead center (BTDC) spark timing. Hydrocarbon and carbon monoxide emissions were reduced with the retardation of spark timings. Nitrogen oxide emissions were continuously increased with the addition of hydrogen in the fuel blend as well as spark timing advance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
  • No Thumbnail Available
    Item
    Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel
    (Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.
    It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.
  • No Thumbnail Available
    Item
    Influence of spark timing on the performance and emission characteristics of gasoline–hydrogen-blended high-speed spark-ignition engine
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2017) Shivaprasad, K.V.; Chitragar, P.R.; Nayak, V.; Kumar, G.N.
    This article experimentally investigates the effect of spark timing on performance and emission characteristics of high-speed spark-ignition (SI) engine operated with different hydrogen–gasoline fuel blends. For this purpose, the conventional carbureted SI engine is modified into an electronically controllable engine, wherein an electronically controllable unit was used to control the ignition timings and injection duration of gasoline. The tests were conducted with different spark timings at the wide open throttle position and 3000 rpm engine speed. The experimental results demonstrated that brake mean effective pressure and engine brake thermal efficiency increased first and then decreased with the increase in spark advance. Peak cylinder pressure, temperature and heat release rate were increased until 20% hydrogen addition and with increased spark timings. NOx emissions were continuously increased with the increment in both spark timings and hydrogen addition, whereas hydrocarbon emissions were increased with spark timings but decreased with hydrogen addition. CO emissions were reduced with the increase in spark timing and hydrogen addition. © 2016 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Rao, G.; Kumar, G.N.; Herbert, M.A.
    Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220 bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NOX emission of 1047 ppm at 220 bar injection pressure at 75% load. © 2018, © 2018 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Effect of 1-pentanol addition and EGR on the combustion, performance and emission characteristic of a CRDI diesel engine
    (Elsevier Ltd, 2020) Radheshyam; Santhosh, K.; Kumar, G.N.
    Experimental study of 1-pentanol addition and EGR rates on the combustion, performance and emission of a CRDI diesel engine is carried out in this work. 1-Pentanol being a higher alcohol has fuel properties comparable to diesel. Experiments were conducted on a 4 stroke two cylinder, CRDI diesel engine running at a constant speed of 2000 rpm for lower load and higher load. Test fuels were prepared by blending the 1-pentanol with diesel, and tests were carried out for 5%, 10%, 20%, 30% and 40%, 1-pentanol blended in diesel on a volume basis. Effect of EGR rates of 10% and 20% were also studied. It had observed that engine can be run up to 30% of 1-pentanol blended fuel without any engine modification, but with raise in the percentage of 1-pentanol in the blends, BSFC increases and BTE decreases. Combustion characteristic for blended fuel depends upon the load. At higher load due to premixed combustion MGT, CP and NHR were almost same compared to the diesel. Reduction in NOx emissions was noted for all the fuel blends at the cost of HC and CO emission. 1-pentanol is a renewable biofuel, with use of 1-pentanol the dependency on petrodiesel can be overcome. © 2019 Elsevier Ltd
  • No Thumbnail Available
    Item
    Experimental analysis of performance and emission characteristics of CRDI diesel engine fueled with 1-pentanol/diesel blends with EGR technique
    (Elsevier Ltd, 2020) Santhosh, K.; Kumar, G.N.; Radheshyam; Sanjay, P.V.
    This research work aims to investigate the effect of higher alcohol blends on performance and emission parameters of CRDI CI engine with various EGR rate. 1-pentanol has improved fuel properties compared to lower alcohols. It can be used as a blend with diesel to mitigate the toxic emissions and to reduce the dependency on diesel fuel. The experiment was carried out in a CRDI CI engine with 1-pentanol/diesel blends (10%, 20% and 30% v/v) as a fuel, the speed of the engine kept constant (2000 rpm) by varying the load from 20 to 80% in step of 20%. Two EGR rates (10% and 20%) were also tested with blends to find the effect on engine characteristics. The performance of the engine reduces with higher 1-pentanol proportion in the blend. The experimental investigation showed that for P30D70 about 3.8% drop in BTE, 9.14% rise in BSFC, 16.7% drop in NOx emission and a slight rise in HC and CO emission was noted at 60% load. The smooth operation of the engine was noted with 1-pentanol/diesel blends and can be concluded that up to 30% of the 1-pentanol can be used as an alternative to the diesel with a slight cost of performance. © 2020 Elsevier Ltd
  • No Thumbnail Available
    Item
    Impact of 1-Hexanol/diesel blends on combustion, performance and emission characteristics of CRDI CI mini truck engine under the influence of EGR
    (Elsevier Ltd, 2020) Santhosh, K.; Kumar, G.N.
    Biofuels are the most promising sustainable and renewable alternative to diesel fuel. In the present renewable energy world, alcohols are gaining prime importance due to their nature of production and fuel properties. The present work aims to investigate the impact of 1-Hexanol and exhaust gas recirculation (10% and 20%) on engine characteristics of the common rail direct injection compression ignition engine. The experiment is carried out on a bench engine. The fraction of 1-Hexanol is varied from 10% to 40% in a step of 10% by volume. The results demonstrate that the use of 1-Hexanol/diesel blends lowers the cylinder pressure and mean gas temperature, which is 4.25% and 1.88% lower at 60% load for 40% 1-Hexanol compared to neat diesel fuel operation. The combustion duration is increased by 2.66?CA for 40% 1-Hexanol at 60% load compared to neat diesel fuel. However, an improvement in net heat release rate is noted which is 13.95% higher at 60% load for 40% 1-Hexanol, this increment is due to prolonged ignition delay. With the use of 1-Hexanol in the engine, there is a drastic reduction in nitrogen oxide emission is observed, this is the greatest impact of 1-Hexanol. However, a slight increment in the hydrocarbon and carbon monoxide emission is also noted due to poor fuel properties like lower cetane number, higher viscosity and higher latent heat of evaporation of 1-Hexanol. Compared to all other blends in the test 10% 1-Hexanol shows comparable results with pure diesel fuel, which is only 2.37% lower in brake thermal efficiency, 3.6% higher in brake specific fuel consumption, 17.55% lower in nitrogen oxide emission, 18.18% higher in hydrocarbon and 33.33% higher in carbon monoxide emission is noted. The exhaust gas recirculation helps in reducing the NOx emission, 40% 1-Hexanol is less sensitive to exhaust gas recirculation. Up to 40% of 1-Hexanol can be used in the CI engine without any modification. It is concluded that 1-Hexanol is a sustainable renewable biofuel due to the reason that even though the use of 1-Hexanol lowers the performance which helps in reducing the NOx emission greatly; the performance can be improved by modifying the engine parameters. © 2020 Elsevier Ltd
  • No Thumbnail Available
    Item
    Effect of injection time on combustion, performance and emission characteristics of direct injection CI engine fuelled with equi-volume of 1-hexanol/diesel blends
    (Elsevier Ltd, 2021) Santhosh, K.; Kumar, G.N.
    In this experimental research work, the effect of 1-Hexanol on engine parameters is studied and to improve the combustion, performance and emission characteristics of CI engine, fuel injection time is advanced and retarded to know the best possible injection time. The experiment is conducted in a twin-cylinder, common rail direct injection diesel engine, speed (2000 rpm) of the engine is constant throughout the experiment and the engine load is varied as 20%, 40%, 60% and 80%. In this experiment equi-volume of 1-Hexanol/diesel blends is used as a fuel, the experiment is conducted for standard (12°BTDC), advanced (15°BTDC) and retard (9°BTDC) injection time. The obtained results are compared with baseline readings taken at standard injection time. The advanced injection time shows the best results compared to standard and retard injection time. The advanced injection time shows improved combustion parameters, the combustion peak moves near to TDC. An increment of 14.28% in BTE is noted for 1-Hexanol blend. The CO and HC emission decreases with advanced injection time, whereas higher NOx emission is noted. It is concluded that 50% of 1-Hexanol can be used in CI engine with slight modification in injection time; the advanced injection time gives improved efficiency. © 2020 Elsevier Ltd