Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Experimental Studies on the Effect of Varying Rates of Part-Cooled EGR in High Pressure Loop on an MPFI Engine Under Variable Speed Operation(Springer Science and Business Media Deutschland GmbH info@springer-sbm.com, 2021) Oommen, L.P.; Kumar, G.N.Researches in automobile sector around the globe are focused on meeting the currently proposed emission norms. Exhaust gas recirculation is one pre-treatment technique that has been found effective in enhancing the combustion and emission characteristics of IC engines and regulating the emission of nitrogen oxides. The present work analyses the effect produced by different rates of partially cooled EGR in a high pressure loop on a multi-cylinder MPFI gasoline engine. Three flow rates of EGR—12%, 18% and 24%—have been studied, and the impact produced on thermal efficiency, specific fuel consumption and emission of macropollutants of the test engine has been analysed under variable speed operation in comparison with normal operation of the engine without recirculation. The temperature of recirculated exhaust gas is so maintained as not to have a negative influence on the fuel consumption characteristics. A reduction in specific fuel consumption is observed which results in a marginal improvement of brake thermal efficiency alongside the advantage obtained in the emissions of the engine. The study proves that the advantages of EGR addition are limited to around 18% above to which the cyclic variations and misfires become predominant, deteriorating the performance and emissions of the test engine. © 2021, Springer Nature Singapore Pte Ltd.Item Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends(Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.Item Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel(Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.Item Effect of exhaust gas recirculation on a CRDI engine fueled with waste plastic oil blend(Elsevier Ltd, 2018) Ayodhya, A.S.; Lamani, V.T.; Bedar, P.; Kumar, G.N.The inevitable rise in the usage of plastic poses a serious threat to the environment owing to their non-biodegradable nature. The lack of proper infrastructure for treating and recycling plastic wastes give rise to the disposal problem. However, the oil synthesized from these waste plastics can be used as an alternative fuel for C.I engines which not only helps to tackle the disposal problem but also aids in recovering precious energy from these wastes. This experimental investigation aims to study the effects of plastic-diesel blend(P30) fuel on the performance, emission and combustion characteristics of a twin cylinder CRDI engine operating at different EGR rates (0%, 10% and 20%). The experimental results showed a slight drop in the engine performance while operating with plastic blend, mainly overall due to its higher viscosity and lower heating value. The vast upsurge of NOX emissions with plastic blend was mitigated by the aid of EGR methodology. Marginal increase in the discharge of regulated emissions like HC, CO and soot were noticed for both plastic blend as well as EGR operations. The experiments were carried out for five different loading conditions varying from 0% to 80% in steps of 20% each and found out that waste plastic-diesel blend can be successfully used as an alternative fuel in diesel vehicles without any prior modifications in the engine. © 2018 Elsevier LtdItem Combustion, performance, and tail pipe emissions of common rail diesel engine fueled with waste plastic oil-diesel blends(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2018) Lamani, V.T.; Yadav, A.K.; Kumar, G.N.The demand for plastic is eternally growing in urban areas and producing enormous quantity of plastic waste. The management and disposal of plastic waste have become a major concern worldwide. The awareness of waste to energy retrieval is one of the promising modes used for the treatment of the waste plastic. The present investigation evaluates the prospective use of waste plastic oil (WPO) as an alternative fuel for diesel engine. Different blends (WPO0, WPO30, and WPO50) with diesel are prepared on a volume basis and the engine is operated. Experiments are conducted for various injection timings (9 deg, 12 deg, 15 deg, and 18 deg BTDC) and for different exhaust gas recirculation (EGR) rates (0%, 10%, 15%, and 20%) at 100 MPa injection pressure. Combustion, performance, and tail pipe emissions of common rail direct injection (CRDI) engine are studied. The NOx, CO, and Soot emissions for waste plastic oil-diesel blends are found more than neat diesel. To reduce the NOx, EGR is employed, which results in reduction of NOx considerably, whereas other emissions, i.e., CO and Soot, get increased with increase in EGR rates. Soot for WPO-diesel blends is higher because of aromatic compounds present in plastic oils. Brake thermal efficiency (BTE) of blends is found to be higher compared to diesel. © 2018 by ASME.Item Effect of bioethanol–diesel blends, exhaust gas recirculation rate and injection timing on performance, emission and combustion characteristics of a common rail diesel engine(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Lamani, V.T.; Baliga M, A.U.; Yadav, A.K.; Kumar, G.N.This investigation is focused on the effect of exhaust gas recirculation (EGR) and injection timing on the performance, combustion and exhaust emission characteristics of common rail direct injection (CRDI) engine fueled with bioethanol-blended diesel using computational fluid dynamics (CFD) simulation. Simulation is carried out for various EGR rates (0, 10, 20 and 30%), two different injection timings, and two different bioethanol–diesel blends (10 and 20%) at injection pressure. The equivalence ratio is kept constant in all the cases of bioethanol–diesel blends. The results indicate that the mean CO formation and ignition delay increase, whereas mean NO formation and in-cylinder temperature decrease, with increase in the EGR rate. Further, with an increase in percentage of the bioethanol blends, CO and soot formation decrease as compared to neat diesel. A significant increase in in-cylinder pressure (15%) is found at 14° before top dead centre (BTDC) compared to 9° BTDC, which leads to an increase in indicated thermal efficiency of 4% for neat diesel at 30% EGR. In the present study, maximum indicated thermal efficiency is obtained in the case of 10 and 20% bioethanol–diesel blend, and remains constant for all EGR rates considered in the study. Obtained results are validated with the available literature data and indicate good agreement. © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.Item Impact of 1-Hexanol/diesel blends on combustion, performance and emission characteristics of CRDI CI mini truck engine under the influence of EGR(Elsevier Ltd, 2020) Santhosh, K.; Kumar, G.N.Biofuels are the most promising sustainable and renewable alternative to diesel fuel. In the present renewable energy world, alcohols are gaining prime importance due to their nature of production and fuel properties. The present work aims to investigate the impact of 1-Hexanol and exhaust gas recirculation (10% and 20%) on engine characteristics of the common rail direct injection compression ignition engine. The experiment is carried out on a bench engine. The fraction of 1-Hexanol is varied from 10% to 40% in a step of 10% by volume. The results demonstrate that the use of 1-Hexanol/diesel blends lowers the cylinder pressure and mean gas temperature, which is 4.25% and 1.88% lower at 60% load for 40% 1-Hexanol compared to neat diesel fuel operation. The combustion duration is increased by 2.66?CA for 40% 1-Hexanol at 60% load compared to neat diesel fuel. However, an improvement in net heat release rate is noted which is 13.95% higher at 60% load for 40% 1-Hexanol, this increment is due to prolonged ignition delay. With the use of 1-Hexanol in the engine, there is a drastic reduction in nitrogen oxide emission is observed, this is the greatest impact of 1-Hexanol. However, a slight increment in the hydrocarbon and carbon monoxide emission is also noted due to poor fuel properties like lower cetane number, higher viscosity and higher latent heat of evaporation of 1-Hexanol. Compared to all other blends in the test 10% 1-Hexanol shows comparable results with pure diesel fuel, which is only 2.37% lower in brake thermal efficiency, 3.6% higher in brake specific fuel consumption, 17.55% lower in nitrogen oxide emission, 18.18% higher in hydrocarbon and 33.33% higher in carbon monoxide emission is noted. The exhaust gas recirculation helps in reducing the NOx emission, 40% 1-Hexanol is less sensitive to exhaust gas recirculation. Up to 40% of 1-Hexanol can be used in the CI engine without any modification. It is concluded that 1-Hexanol is a sustainable renewable biofuel due to the reason that even though the use of 1-Hexanol lowers the performance which helps in reducing the NOx emission greatly; the performance can be improved by modifying the engine parameters. © 2020 Elsevier LtdItem The effect of tri-fuel blends on engine characteristics of a direct injection diesel engine with exhaust gas recirculation(Taylor and Francis Ltd., 2022) Santhosh, K.; Kumar, G.N.; Shahapur, S.Biofuels are the most promising alternative to petro-diesel. In this work, the combined effect of mahua biodiesel and 1-Hexanol is studied on the engine characteristics. The concentration of both 1-Hexanol and mahua biodiesel is varied, 10%, 20%, and 30% each with diesel fuel. Common rail direct injection diesel engine is used in this study. Engine load is varied from 20% to 80% in step of 20%, the speed of the engine is constant throughout the experiment. Biofuel blends showed improved cylinder pressure and mean gas temperature at a higher engine load. At 60% load, 10H10M80D (10% 1-Hexanol/10% mahua biodiesel/80% diesel) showed 3.45% lower thermal efficiency and 6.11% higher fuel consumption compared to diesel. At 60% load, all the biofuel blends showed 50% lower carbon monoxide emission. At 60% load, 10H10M80D showed 33.33% lower hydrocarbon emission and 0.96% higher nitrogen oxide emission compared to baseline readings. The biofuel blends are less sensitive to exhaust gas recirculation (EGR) due to the oxygenated nature of biofuels. With 20% EGR, at 60% load, 10H10M80D showed 39.48% lower nitrogen oxide compared to no EGR. The results of 10H10M80D showed the best performance at all loads. © 2022 Taylor & Francis Group, LLC.Item Effects of compression and mixing ratio on NH3/H2 fueled Si engine performance, combustion stability, and emission(Elsevier Ltd, 2022) Dinesh, M.H.; Kumar, G.N.Carbon-free fuels for the worldwide decarbonization movement are ammonia and hydrogen. The experiment is conducted under WOT conditions with a constant ignition timing of 24°CA BTDC to evaluate performance, combustion stability, and emissions with varying CR (12 to 15), hydrogen energy fractions (5 to 21%), and engine speeds between 1500 and 1700 RPM. BP increased by 31.2% at 1700RPM and BTE increased by 39.0% at 1500RPM, despite a 9% decrease in volumetric efficiency at 1700RPM, from 5% hydrogen fraction at CR12 to 21% hydrogen fraction at CR15.The combustion process is sped up by the effect of hydrogen fraction and CR, causing the flame development and propagation period to shorten. NOx emission was increased significantly with hydrogen and CR, with an increase of 42.34% from 5% hydrogen at CR12 to 21% hydrogen at CR15 at 1700 RPM. Excessive NOx emissions are a drawback that can be successfully controlled by installing after treatment or exhaust gas recirculation technologies. Ammonia is another important key element used to reduce NOx emissions from vehicles because it is used in SCR. © 2022 The AuthorsItem Experimental Analysis of Conjoint Effect of Semi-Cooled Exhaust Recirculation on Combustion of Liquid Phase Hydrocarbons Under Uniform Magnetic Fields(Institute for Ionics, 2022) Oommen, L.P.; Kumar, G.N.In the context of increasing the energy utilization of hastily depleting conventional hydrocarbon based fuels and regulating the associated emissions, the present experimental work investigates the conjoint effect of partially cooled exhaust gas recirculation on magnetic field-assisted combustion of gasoline in a multicylinder MPFI spark ignition engine. At the factory set ignition timing of 5 degree BTDC, an optimal mass of burnt gas (18%) within the tolerance limit of the engine determined through prior experiments is recirculated into the combustion chamber after partially cooling in a radiator assembly. The combustible charge which blends with the inert exhaust mixture is prepared from gasoline pretreated under a potent magnetic field generated using NdFeB rare earth magnets capable of enhancing the oxidation process. The intensity of applied magnetic field and the locus of magnetization are decided based on primal experiments. Combustion under the conjoint effect of the set modifications is studied in terms of fuel economy, thermal efficiency and regulated emissions of the engine in which significant improvement is noted. Cyclic variability in combustion is evaluated through the statistical analysis of COV of peak cylinder pressures and mean effective pressures which predicts reduction in probability of misfires. Experimental results portray an enhancement in fuel economy by 14.6% and reduction in cyclic variability by 11.56% under synergy of optimal recirculation and polarization when compared to baseline gasoline combustion and individual impact of recirculation of cooled exhaust gases. © 2022, King Fahd University of Petroleum & Minerals.