Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Kumar, G.N.Subject: search.filters.subject.Engine cylinders

Search Results

Now showing 1 - 8 of 8
  • No Thumbnail Available
    Item
    Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends
    (Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.
    This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.
  • No Thumbnail Available
    Item
    Experimental Investigation of Variations in Spark Timing using a Spark-Ignition Engine with Hydrogen-Blended Gasoline
    (Wiley-VCH Verlag info@wiley-vch.de, 2015) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.
    This study describes an experiment conducted using an electronically controllable single-cylinder high-speed gasoline engine to analyze the performance and emissions characteristics of various hydrogen-gasoline blends. The experiments have been conducted for various engine speeds and spark timings at the wide open throttle position. The experimental results revealed that the engine brake thermal efficiency and brake mean effective pressure first increase and then decrease with the increase engine speed at all spark timings. The minimum amount of brake specific energy consumption was observed for 20% hydrogen addition in the total fuel blend at 3000rpm engine speed and 14°crank angle (CA) before top dead center (BTDC) spark timing. Hydrocarbon and carbon monoxide emissions were reduced with the retardation of spark timings. Nitrogen oxide emissions were continuously increased with the addition of hydrogen in the fuel blend as well as spark timing advance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
  • No Thumbnail Available
    Item
    Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel
    (Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.
    It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.
  • No Thumbnail Available
    Item
    Effect of exhaust gas recirculation on a CRDI engine fueled with waste plastic oil blend
    (Elsevier Ltd, 2018) Ayodhya, A.S.; Lamani, V.T.; Bedar, P.; Kumar, G.N.
    The inevitable rise in the usage of plastic poses a serious threat to the environment owing to their non-biodegradable nature. The lack of proper infrastructure for treating and recycling plastic wastes give rise to the disposal problem. However, the oil synthesized from these waste plastics can be used as an alternative fuel for C.I engines which not only helps to tackle the disposal problem but also aids in recovering precious energy from these wastes. This experimental investigation aims to study the effects of plastic-diesel blend(P30) fuel on the performance, emission and combustion characteristics of a twin cylinder CRDI engine operating at different EGR rates (0%, 10% and 20%). The experimental results showed a slight drop in the engine performance while operating with plastic blend, mainly overall due to its higher viscosity and lower heating value. The vast upsurge of NOX emissions with plastic blend was mitigated by the aid of EGR methodology. Marginal increase in the discharge of regulated emissions like HC, CO and soot were noticed for both plastic blend as well as EGR operations. The experiments were carried out for five different loading conditions varying from 0% to 80% in steps of 20% each and found out that waste plastic-diesel blend can be successfully used as an alternative fuel in diesel vehicles without any prior modifications in the engine. © 2018 Elsevier Ltd
  • No Thumbnail Available
    Item
    NOx reduction studies on a diesel engine operating on waste plastic oil blend using selective catalytic reduction technique
    (Elsevier B.V., 2019) Ayodhya, A.S.; Lamani, V.T.; Thirumoorthy, M.; Kumar, G.N.
    The constant escalation in the consumption of petroleum products has compelled researchers to discover for new alternative fuels which can be successfully incorporated in the existing automotive engines. Oil derived from waste plastics is one such alternative, which not only ensures longevity of fossil fuels but also assists in bringing down the hazardous impacts caused by the improper disposal of plastic wastes. This work focuses on the utilization of valuable energy of toxic non-biodegradable waste plastics to lucratively be used as an alternative fuel. An attempt was further made to reduce the NO X emissions which increased with the use of waste plastic oil blend. The main objective of this experimental investigation is to study the performance & emission characteristics of a twin cylinder CRDI engine subjected to selective catalytic reduction (SCR) after-treatment technique. Different flow rates of ammonia as a reducing agent were tested and concluded that a flow rate of 0.5 kg/hr furnishes optimum results. A comparison of NO X reduction efficiency was also made between SCR and EGR techniques. The comparison eventually indicated that SCR gives better NO X conversion efficiency at higher loads without any adverse effect on the engine performance while operating on Waste Plastic Oil blend (P30). © 2018 Energy Institute
  • No Thumbnail Available
    Item
    Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Rao, G.; Kumar, G.N.; Herbert, M.A.
    Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220 bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NOX emission of 1047 ppm at 220 bar injection pressure at 75% load. © 2018, © 2018 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Investigation of preheated Dhupa seed oil biodiesel as an alternative fuel on the performance, emission and combustion in a CI engine
    (Elsevier Ltd, 2021) Kodate, S.V.; Satyanarayana Raju, P.; Yadav, A.K.; Kumar, G.N.
    The present study investigates the suitability of preheated Vateria indica methyl ester (VIME) as an alternative fuel for a diesel engine. VIME is a renewable, non-toxic and sustainable alternative biodiesel obtained from Dhupa fat by transesterification. This study aims to evaluate the combustion, performance, and emission characteristics of four different blends such as B0 (0% VIME and 100% mineral diesel), B30, B50 and B100 at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out in a single cylinder diesel engine at optimum loading condition and fixed speed. Results are obtained in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), in-cylinder pressure, heat release rate and exhaust emissions (CO, HC, NOX, CO2 and soot). It is observed that the preheating of blends decreases the viscosity which enhances fuel spray characteristics, leading to higher engine performance, lower CO and HC emissions with a slight increase in NOX and CO2 emissions. BTE and peak in-cylinder pressure for B100 at 95 °C and 75% load are increased by 7.44%, 2.97% respectively compared to unheated B100 biodiesel. BSFC, CO, HC emissions at 75% load for B100 at 95 °C are reduced by 26.73%, 28.08%, 42.7% respectively compared to unheated B100. © 2021 Elsevier Ltd
  • No Thumbnail Available
    Item
    Effect of fuel injection timing on engine characteristics with an equal volume of 1-heptanol/diesel blend in a CRDI CI engine
    (Elsevier B.V., 2025) Bhumula, K.B.; Kumar, G.N.
    1-Heptanol (C7H15OH) is a superior and eco-friendly alternative to diesel fuel derived from renewable biomass to address environmental concerns and mitigate fossil fuel depletion. Testing in this research involved using a single-cylinder, four-stroke CRDI diesel engine. The engine ran at a constant speed of 1500 rpm and was fueled with a blend of 50 % 1-heptanol/diesel by volume. The research focused on examining the impact of different injection timings (21°, 23°, and 25 °CA bTDC) specifically, retarded, standard, and advanced timings, as well as varying engine loads of 4, 8 and 12 kg on engine performance, combustion efficiency, and emissions. Experimental test results showed that blending 1-heptanol/diesel fuel led to a substantial decrease in NOx emissions and smoke opacity, which were reduced by 27 % and 26 %, respectively. However, when using a 50 % 1-heptanol/diesel blend and testing with advanced injection timing, there was a 2.26 % decrease in BTE and a 5.1 % increase in BSFC compared to pure diesel. The injection timing advancement improves premixed combustion but increases HC and CO emissions. Research suggests a 50 % blend of 1-Heptanol as a promising renewable fuel for diesel engines, with slight modifications. © 2025 The Authors